[Freedreno] [PATCH 3/5] arm64: dts: qcom: qrb5165-rb5: add onboard USB-C redriver

[Dmitry Baryshkov]

On 12/07/2023 02:04, Konrad Dybcio wrote:
> On 12.07.2023 01:01, Dmitry Baryshkov wrote:
>> On Wed, 12 Jul 2023 at 01:59, Konrad Dybcio <konrad.dybcio at linaro.org> wrote:
>>>
>>> On 12.07.2023 00:39, Dmitry Baryshkov wrote:
>>>> On 12/07/2023 00:36, Konrad Dybcio wrote:
>>>>> On 9.07.2023 06:19, Dmitry Baryshkov wrote:
>>>>>> Add the nb7vpq904m, onboard USB-C redriver / retimer.
>>>>>>
>>>>>> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov at linaro.org>
>>>>>> ---
>>>>> [...]
>>>>>
>>>>>> +            port at 1 {
>>>>>> +                reg = <1>;
>>>>>> +
>>>>>> +                redriver_phy_con_ss: endpoint {
>>>>>> +                    remote-endpoint = <&usb_1_qmpphy_typec_mux_in>;
>>>>>> +                    data-lanes = <0 1 2 3>;
>>>>> That's USB+DP lines combined, or how does it work? I'm confused :/
>>>>
>>>> 4 generic purpose SS lanes, which can be purposed for USB or for DP.
>>> Okay, so my gut did better than my brain.
>>>
>>> Other than that, I'm reading the bindings and it looks like ports 0 and
>>> 1 may possibly be swapped?
>>
>> Yes. But if I get schematics right, the lanes are not swapped in this case.
> I'm not talking about the 0123-3210 swap, but rather in/out being swapped.
> Unless I'm reading the bindings wrong (or they may be written in a
> confusing way).

Hmm, no. port at 0 goes to the connector, port at 1 to SS PHY, port at 2 to SBU 
source.

> 
> Konrad
>>
>>>
>>> Konrad
>>>>
>>>>>
>>>>> Konrad
>>>>>> +                };
>>>>>> +            };
>>>>>> +
>>>>>> +            port at 2 {
>>>>>> +                reg = <2>;
>>>>>> +
>>>>>> +                redriver_usb_con_sbu: endpoint {
>>>>>> +                    remote-endpoint = <&pm8150b_typec_sbu_out>;
>>>>>> +                };
>>>>>> +            };
>>>>>> +        };
>>>>>> +    };
>>>>>>    };
>>>>>>      &mdss {
>>>>>> @@ -1294,7 +1334,7 @@ &usb_1_qmpphy {
>>>>>>    };
>>>>>>      &usb_1_qmpphy_typec_mux_in {
>>>>>> -    remote-endpoint = <&pm8150b_typec_mux_out>;
>>>>>> +    remote-endpoint = <&redriver_phy_con_ss>;
>>>>>>    };
>>>>>>      &usb_2 {
>>>>>> @@ -1382,7 +1422,15 @@ pm8150b_role_switch_out: endpoint {
>>>>>>                port at 1 {
>>>>>>                    reg = <1>;
>>>>>>                    pm8150b_typec_mux_out: endpoint {
>>>>>> -                    remote-endpoint = <&usb_1_qmpphy_typec_mux_in>;
>>>>>> +                    remote-endpoint = <&redriver_usb_con_ss>;
>>>>>> +                };
>>>>>> +            };
>>>>>> +
>>>>>> +            port at 2 {
>>>>>> +                reg = <2>;
>>>>>> +
>>>>>> +                pm8150b_typec_sbu_out: endpoint {
>>>>>> +                    remote-endpoint = <&redriver_usb_con_sbu>;
>>>>>>                    };
>>>>>>                };
>>>>>>            };
>>>>
>>
>>
>>

-- 
With best wishes
Dmitry