[Freedreno] [PATCH v2] drm/msm/dsi: Document DSC related pclk_rate and hdisplay calculations

[Abhinav Kumar]

On 6/19/2023 2:06 PM, Dmitry Baryshkov wrote:
> Provide actual documentation for the pclk and hdisplay calculations in
> the case of DSC compression being used.
> 
> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov at linaro.org>
> ---
> 
> Changes since v1:
> - Converted dsi_adjust_pclk_for_compression() into kerneldoc (Marijn)
> - Added a pointer from dsi_timing_setup() docs to
>    dsi_adjust_pclk_for_compression() (Marijn)
> - Fixed two typo (Marijn)
> 
> ---
>   drivers/gpu/drm/msm/dsi/dsi_host.c | 40 ++++++++++++++++++++++++++++--
>   1 file changed, 38 insertions(+), 2 deletions(-)
> 
> diff --git a/drivers/gpu/drm/msm/dsi/dsi_host.c b/drivers/gpu/drm/msm/dsi/dsi_host.c
> index 3f6dfb4f9d5a..a8a31c3dd168 100644
> --- a/drivers/gpu/drm/msm/dsi/dsi_host.c
> +++ b/drivers/gpu/drm/msm/dsi/dsi_host.c
> @@ -528,6 +528,25 @@ void dsi_link_clk_disable_v2(struct msm_dsi_host *msm_host)
>   	clk_disable_unprepare(msm_host->byte_clk);
>   }
>   
> +/**
> + * dsi_adjust_pclk_for_compression() - Adjust the pclk rate for compression case
> + * @mode: the selected mode for the DSI output
> + * @dsc: DRM DSC configuration for this DSI output
> + *
> + * Adjust the pclk rate by calculating a new hdisplay proportional to
> + * the compression ratio such that:
> + *     new_hdisplay = old_hdisplay * compressed_bpp / uncompressed_bpp
> + *
> + * Porches do not need to be adjusted:
> + * - For the VIDEO mode they are not compressed by DSC and are passed as is.
> + * - For the CMD mode there are no actual porches. Instead these fields
> + *   currently represent the overhead to the image data transfer. As such, they
> + *   are calculated for the final mode parameters (after the compression) and
> + *   are not to be adjusted too.
> + *
> + *  FIXME: Reconsider this if/when CMD mode handling is rewritten to use
> + *  refresh rate and data overhead as a starting point of the calculations.
> + */
>   static unsigned long dsi_adjust_pclk_for_compression(const struct drm_display_mode *mode,
>   		const struct drm_dsc_config *dsc)

I am fine with this part of the doc.

>   {
> @@ -926,8 +945,25 @@ static void dsi_timing_setup(struct msm_dsi_host *msm_host, bool is_bonded_dsi)
>   		if (ret)
>   			return;
>   
> -		/* Divide the display by 3 but keep back/font porch and
> -		 * pulse width same
> +		/*
> +		 * DPU sends 3 bytes per pclk cycle to DSI. If compression is
> +		 * not used, a single pixel is transferred at each pulse, no
> +		 * matter what bpp or pixel format is used. In case of DSC
> +		 * compression this results (due to data alignment
> +		 * requirements) in a transfer of 3 compressed pixel per pclk
> +		 * cycle.
> +		 *

I dont want to talk about data alignment nor formats and I will not ack 
any references to those.

I would like to keep this simple and say that DPU sends 3 bytes of 
compressed data / pclk (6 with widebus enabled) and all this math is 
doing is that its calculating number of bytes and diving it by 3 OR 6 
with widebus to calculate the pclk cycles. Thats it.

> +		 * If widebus is enabled, bus width is extended to 6 bytes.
> +		 * This way the DPU can transfer 6 compressed pixels with bpp
> +		 * less or equal to 8 or 3 compressed pixels in case bpp is
> +		 * greater than 8.
> +		 *
> +		 * The back/font porch and pulse width are kept intact.  They
> +		 * represent timing parameters rather than actual data
> +		 * transfer. See the documentation of
> +		 * dsi_adjust_pclk_for_compression().

this part is fine.

> +		 *
> +		 * XXX: widebus is not supported by the driver (yet).
>   		 */
>   		h_total -= hdisplay;
>   		hdisplay = DIV_ROUND_UP(msm_dsc_get_bytes_per_line(msm_host->dsc), 3);