[Freedreno] [PATCH v3 2/3] drm/msm/dpu: use dpu core's major version to enable data compress

[Dmitry Baryshkov]

On 29/06/2023 22:29, Abhinav Kumar wrote:
> Instead of using a feature bit to decide whether to enable data
> compress or not for DSC use-cases, use dpu core's major version instead.
> This will avoid defining feature bits for every bit level details of
> registers.
> 
> Also, rename the intf's enable_compression() op to program_datapath()
> and allow it to accept a struct intf_dpu_datapath_cfg to program
> all the bits at once. This can be re-used by widebus later on as
> well as it touches the same register.

Two separate commits please, because...

> Signed-off-by: Abhinav Kumar <quic_abhinavk at quicinc.com>
> ---
>   .../gpu/drm/msm/disp/dpu1/dpu_encoder_phys_cmd.c |  9 +++++++--
>   drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c      |  9 +++++----
>   drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.h      | 16 ++++++++++++++--
>   3 files changed, 26 insertions(+), 8 deletions(-)
> 
> diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_cmd.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_cmd.c
> index b856c6286c85..f4e15b4c4cc9 100644
> --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_cmd.c
> +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_cmd.c
> @@ -50,6 +50,7 @@ static void _dpu_encoder_phys_cmd_update_intf_cfg(
>   			to_dpu_encoder_phys_cmd(phys_enc);
>   	struct dpu_hw_ctl *ctl;
>   	struct dpu_hw_intf_cfg intf_cfg = { 0 };
> +	struct dpu_kms *dpu_kms = phys_enc->dpu_kms;
>   
>   	ctl = phys_enc->hw_ctl;
>   	if (!ctl->ops.setup_intf_cfg)
> @@ -68,8 +69,12 @@ static void _dpu_encoder_phys_cmd_update_intf_cfg(
>   				phys_enc->hw_intf,
>   				phys_enc->hw_pp->idx);
>   
> -	if (intf_cfg.dsc != 0 && phys_enc->hw_intf->ops.enable_compression)
> -		phys_enc->hw_intf->ops.enable_compression(phys_enc->hw_intf);
> +	if (intf_cfg.dsc != 0 && dpu_kms->catalog->core_major_version >= 0x7) {

... because this becomes incorrect. The datapath should be programmed in 
all the cases, if there is a corresponding callback. intf_cfg.dsc should 
be used as a condition to set datapath_cfg.


> +		struct intf_dpu_datapath_cfg datapath_cfg = { 0 };

No need for `0' in the init, empty braces would be enough.

> +
> +		datapath_cfg.data_compress = true;
> +		phys_enc->hw_intf->ops.program_datapath(phys_enc->hw_intf, &datapath_cfg);
> +	}
>   }
>   
>   static void dpu_encoder_phys_cmd_pp_tx_done_irq(void *arg, int irq_idx)
> diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c
> index 5b0f6627e29b..85333df08fbc 100644
> --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c
> +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c
> @@ -513,11 +513,13 @@ static void dpu_hw_intf_disable_autorefresh(struct dpu_hw_intf *intf,
>   
>   }
>   
> -static void dpu_hw_intf_enable_compression(struct dpu_hw_intf *ctx)
> +static void dpu_hw_intf_program_datapath(struct dpu_hw_intf *ctx,
> +					 struct intf_dpu_datapath_cfg *datapath_cfg)
>   {
>   	u32 intf_cfg2 = DPU_REG_READ(&ctx->hw, INTF_CONFIG2);
>   
> -	intf_cfg2 |= INTF_CFG2_DCE_DATA_COMPRESS;
> +	if (datapath_cfg->data_compress)
> +		intf_cfg2 |= INTF_CFG2_DCE_DATA_COMPRESS;
>   
>   	DPU_REG_WRITE(&ctx->hw, INTF_CONFIG2, intf_cfg2);
>   }
> @@ -543,8 +545,7 @@ static void _setup_intf_ops(struct dpu_hw_intf_ops *ops,
>   		ops->disable_autorefresh = dpu_hw_intf_disable_autorefresh;
>   	}
>   
> -	if (cap & BIT(DPU_INTF_DATA_COMPRESS))
> -		ops->enable_compression = dpu_hw_intf_enable_compression;
> +	ops->program_datapath = dpu_hw_intf_program_datapath;

The `core_major_version >= 7' should either be here or in the callback 
itself.

>   }
>   
>   struct dpu_hw_intf *dpu_hw_intf_init(const struct dpu_intf_cfg *cfg,
> diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.h b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.h
> index 99e21c4137f9..f736dca38463 100644
> --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.h
> +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.h
> @@ -48,6 +48,11 @@ struct intf_status {
>   	u32 line_count;		/* current line count including blanking */
>   };
>   
> +struct intf_dpu_datapath_cfg {
> +	u8 data_compress;	/* enable data compress between dpu and dsi */
> +	/* can be expanded for other programmable bits */
> +};

I'd say, dpu_datapath is too generic. What about  intf_cmd_mode_cfg?

> +
>   /**
>    * struct dpu_hw_intf_ops : Interface to the interface Hw driver functions
>    *  Assumption is these functions will be called after clocks are enabled
> @@ -70,7 +75,7 @@ struct intf_status {
>    * @get_autorefresh:            Retrieve autorefresh config from hardware
>    *                              Return: 0 on success, -ETIMEDOUT on timeout
>    * @vsync_sel:                  Select vsync signal for tear-effect configuration
> - * @enable_compression:         Enable data compression
> + * @program_datapath:           Program the DPU to interface datapath for relevant chipsets
>    */
>   struct dpu_hw_intf_ops {
>   	void (*setup_timing_gen)(struct dpu_hw_intf *intf,
> @@ -108,7 +113,14 @@ struct dpu_hw_intf_ops {
>   	 */
>   	void (*disable_autorefresh)(struct dpu_hw_intf *intf, uint32_t encoder_id, u16 vdisplay);
>   
> -	void (*enable_compression)(struct dpu_hw_intf *intf);
> +	/**
> +	 * Program the DPU to intf datapath by specifying
> +	 * which of the settings need to be programmed for
> +	 * use-cases which need DPU-intf handshake such as
> +	 * widebus, compression etc.

This is not a valid kerneldoc.

> +	 */
> +	void (*program_datapath)(struct dpu_hw_intf *intf,
> +				 struct intf_dpu_datapath_cfg *datapath_cfg);
>   };
>   
>   struct dpu_hw_intf {

-- 
With best wishes
Dmitry