[Freedreno] [PATCH v3 2/3] drm/msm/dpu: use dpu core's major version to enable data compress
Dmitry Baryshkov
dmitry.baryshkov at linaro.org
Fri Jun 30 03:22:52 UTC 2023
On 30/06/2023 06:07, Abhinav Kumar wrote:
>
>
> On 6/29/2023 5:20 PM, Dmitry Baryshkov wrote:
>> On 29/06/2023 22:29, Abhinav Kumar wrote:
>>> Instead of using a feature bit to decide whether to enable data
>>> compress or not for DSC use-cases, use dpu core's major version instead.
>>> This will avoid defining feature bits for every bit level details of
>>> registers.
>>>
>>> Also, rename the intf's enable_compression() op to program_datapath()
>>> and allow it to accept a struct intf_dpu_datapath_cfg to program
>>> all the bits at once. This can be re-used by widebus later on as
>>> well as it touches the same register.
>>
>> Two separate commits please, because...
>>
>
> I thought of it but it seemed better together and was the only way I
> could think of. Please see below.
>
>>> Signed-off-by: Abhinav Kumar <quic_abhinavk at quicinc.com>
>>> ---
>>> .../gpu/drm/msm/disp/dpu1/dpu_encoder_phys_cmd.c | 9 +++++++--
>>> drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c | 9 +++++----
>>> drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.h | 16 ++++++++++++++--
>>> 3 files changed, 26 insertions(+), 8 deletions(-)
>>>
>>> diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_cmd.c
>>> b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_cmd.c
>>> index b856c6286c85..f4e15b4c4cc9 100644
>>> --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_cmd.c
>>> +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_cmd.c
>>> @@ -50,6 +50,7 @@ static void _dpu_encoder_phys_cmd_update_intf_cfg(
>>> to_dpu_encoder_phys_cmd(phys_enc);
>>> struct dpu_hw_ctl *ctl;
>>> struct dpu_hw_intf_cfg intf_cfg = { 0 };
>>> + struct dpu_kms *dpu_kms = phys_enc->dpu_kms;
>>> ctl = phys_enc->hw_ctl;
>>> if (!ctl->ops.setup_intf_cfg)
>>> @@ -68,8 +69,12 @@ static void _dpu_encoder_phys_cmd_update_intf_cfg(
>>> phys_enc->hw_intf,
>>> phys_enc->hw_pp->idx);
>>> - if (intf_cfg.dsc != 0 && phys_enc->hw_intf->ops.enable_compression)
>>> - phys_enc->hw_intf->ops.enable_compression(phys_enc->hw_intf);
>>> + if (intf_cfg.dsc != 0 && dpu_kms->catalog->core_major_version >=
>>> 0x7) {
>>
>> ... because this becomes incorrect. The datapath should be programmed
>> in all the cases, if there is a corresponding callback. intf_cfg.dsc
>> should be used as a condition to set datapath_cfg.
>>
>
> The issue is that today we do not have dpu_mdss_cfg as part of
> dpu_hw_intf nor _setup_intf_ops because all of those have been dropped
> with some rework or cleanup.
Pass dpu_mdss_cfg to dpu_hw_intf_init(). It was removed as a cleanup,
now we can reintroduce it.
>
> Ideally even I would like to assign this op only for core_rev >=7 but
> that information is no longer available. We would have to start passing
> the major and minor versions to _setup_intf_ops() to go with that
> approach. So without making all of those changes, the only way I had was
> to assign the op unconditionally but call it only for major_rev >= 7.
>
> Passing core_rev to the op itself so that we can write the register only
> for core_rev >=7 is an option but then what if some bits start becoming
> usable only after minor rev. then we will have to start passing major
> and minor rev to program_datapath too. Again getting little messy.
>
> I am open to ideas to achieve the goal of assigning this op only for
> core_rev >=7 other than what I wrote above.
>
>>
>>> + struct intf_dpu_datapath_cfg datapath_cfg = { 0 };
>>
>> No need for `0' in the init, empty braces would be enough.
>>
>
> ack.
>
>>> +
>>> + datapath_cfg.data_compress = true;
>>> + phys_enc->hw_intf->ops.program_datapath(phys_enc->hw_intf,
>>> &datapath_cfg);
>>> + }
>>> }
>>> static void dpu_encoder_phys_cmd_pp_tx_done_irq(void *arg, int
>>> irq_idx)
>>> diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c
>>> b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c
>>> index 5b0f6627e29b..85333df08fbc 100644
>>> --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c
>>> +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c
>>> @@ -513,11 +513,13 @@ static void
>>> dpu_hw_intf_disable_autorefresh(struct dpu_hw_intf *intf,
>>> }
>>> -static void dpu_hw_intf_enable_compression(struct dpu_hw_intf *ctx)
>>> +static void dpu_hw_intf_program_datapath(struct dpu_hw_intf *ctx,
>>> + struct intf_dpu_datapath_cfg *datapath_cfg)
>>> {
>>> u32 intf_cfg2 = DPU_REG_READ(&ctx->hw, INTF_CONFIG2);
>>> - intf_cfg2 |= INTF_CFG2_DCE_DATA_COMPRESS;
>>> + if (datapath_cfg->data_compress)
>>> + intf_cfg2 |= INTF_CFG2_DCE_DATA_COMPRESS;
>>> DPU_REG_WRITE(&ctx->hw, INTF_CONFIG2, intf_cfg2);
>>> }
>>> @@ -543,8 +545,7 @@ static void _setup_intf_ops(struct
>>> dpu_hw_intf_ops *ops,
>>> ops->disable_autorefresh = dpu_hw_intf_disable_autorefresh;
>>> }
>>> - if (cap & BIT(DPU_INTF_DATA_COMPRESS))
>>> - ops->enable_compression = dpu_hw_intf_enable_compression;
>>> + ops->program_datapath = dpu_hw_intf_program_datapath;
>>
>> The `core_major_version >= 7' should either be here or in the callback
>> itself.
>>
>
> Yes, ideally I would like it like that but please see above why I
> couldnt do it.
>
>>> }
>>> struct dpu_hw_intf *dpu_hw_intf_init(const struct dpu_intf_cfg *cfg,
>>> diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.h
>>> b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.h
>>> index 99e21c4137f9..f736dca38463 100644
>>> --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.h
>>> +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.h
>>> @@ -48,6 +48,11 @@ struct intf_status {
>>> u32 line_count; /* current line count including blanking */
>>> };
>>> +struct intf_dpu_datapath_cfg {
>>> + u8 data_compress; /* enable data compress between dpu and dsi */
>>> + /* can be expanded for other programmable bits */
>>> +};
>>
>> I'd say, dpu_datapath is too generic. What about intf_cmd_mode_cfg?
>>
>
> The goal was to keep it generic. Its actually the handshake between DPU
> and interface datapath so I chose that name.
Do you have plans of using it for the video mode?
>
> This is not specific to command mode and intf_cfg is already there so I
> chose that one :)
>
>>> +
>>> /**
>>> * struct dpu_hw_intf_ops : Interface to the interface Hw driver
>>> functions
>>> * Assumption is these functions will be called after clocks are
>>> enabled
>>> @@ -70,7 +75,7 @@ struct intf_status {
>>> * @get_autorefresh: Retrieve autorefresh config from
>>> hardware
>>> * Return: 0 on success, -ETIMEDOUT on
>>> timeout
>>> * @vsync_sel: Select vsync signal for tear-effect
>>> configuration
>>> - * @enable_compression: Enable data compression
>>> + * @program_datapath: Program the DPU to interface
>>> datapath for relevant chipsets
>>> */
>>> struct dpu_hw_intf_ops {
>>> void (*setup_timing_gen)(struct dpu_hw_intf *intf,
>>> @@ -108,7 +113,14 @@ struct dpu_hw_intf_ops {
>>> */
>>> void (*disable_autorefresh)(struct dpu_hw_intf *intf, uint32_t
>>> encoder_id, u16 vdisplay);
>>> - void (*enable_compression)(struct dpu_hw_intf *intf);
>>> + /**
>>> + * Program the DPU to intf datapath by specifying
>>> + * which of the settings need to be programmed for
>>> + * use-cases which need DPU-intf handshake such as
>>> + * widebus, compression etc.
>>
>> This is not a valid kerneldoc.
>>
>
> hmmm ... ok so just // ?
>
> I referred disable_autorefresh from above and did the same.
>
>>> + */
>>> + void (*program_datapath)(struct dpu_hw_intf *intf,
>>> + struct intf_dpu_datapath_cfg *datapath_cfg);
>>> };
>>> struct dpu_hw_intf {
>>
--
With best wishes
Dmitry
More information about the Freedreno
mailing list