[Freedreno] [PATCH v5 0/8] drm/i915: move DSC RC tables to drm_dsc_helper.c

[Jani Nikula]

On Thu, 04 May 2023, Dmitry Baryshkov <dmitry.baryshkov at linaro.org> wrote:
> Other platforms (msm) will benefit from sharing the DSC config setup
> functions. This series moves parts of static DSC config data from the
> i915 driver to the common helpers to be used by other drivers.
>
> Note: the RC parameters were cross-checked against config files found in
> DSC model 2021062, 20161212 (and 20150914). The first patch modifies
> tables according to those config files, while preserving parameter
> values using the code. I have not changed one of the values in the
> pre-SCR config file as it clearly looks like a typo in the config file,
> considering the table E in DSC 1.1 and in the DSC 1.1 SCR.

As I believe I've said before, I think it's fine to merge these either
via drm-intel or drm-misc. Which do you prefer?

BR,
Jani.



>
> Chances since v4:
> - Rebased on top of drm-intel-next
> - Cut the first 8 patches of the series to ease merging. The rest of the
>   patches will go afterwards.
>
> Chances since v3:
> - Rebased on top of drm-intel-next
> - Dropped the msm patch to make patchset fully mergeable through
>   drm-intel
> - Made drm_dsc_set_const_params() ignore rc_model_size, picked up
>   drm_dsc_set_initial_scale_value() patch by Jessica and switched
>   intel_vdsc.c to use those two helpers.
> - Added a patch to make i915 actually use rc_tgt_offset_high,
>   rc_tgt_offset_low and rc_edge_factor from struct drm_dsc_config.
>
> Chances since v2:
> - Rebased on top of drm-intel-next
>
> Chances since v1:
> - Made drm_dsc_rc_buf_thresh static rather than exporting it
> - Switched drm_dsc_rc_buf_thresh loop to use ARRAY_SIZE. Added
>   BUILD_BUG_ON's to be sure that array sizes are correct
> - Fixed rc_parameters_data indentation to be logical and tidy
> - Fixed drm_dsc_setup_rc_params() kerneldoc
> - Added a clause to drm_dsc_setup_rc_params() to verify bpp and bpc
>   being set.
> - Fixed range_bpg_offset programming in calculate_rc_params()
> - Fixed bpp vs bpc bug in intel_dsc_compute_params()
> - Added FIXME comment next to the customizations in
>   intel_dsc_compute_params().
>
> Dmitry Baryshkov (8):
>   drm/i915/dsc: change DSC param tables to follow the DSC model
>   drm/i915/dsc: move rc_buf_thresh values to common helper
>   drm/i915/dsc: move DSC tables to DRM DSC helper
>   drm/i915/dsc: stop using interim structure for calculated params
>   drm/display/dsc: use flat array for rc_parameters lookup
>   drm/display/dsc: split DSC 1.2 and DSC 1.1 (pre-SCR) parameters
>   drm/display/dsc: include the rest of pre-SCR parameters
>   drm/display/dsc: add YCbCr 4:2:2 and 4:2:0 RC parameters
>
>  drivers/gpu/drm/display/drm_dsc_helper.c  | 986 ++++++++++++++++++++++
>  drivers/gpu/drm/i915/display/intel_vdsc.c | 443 ++--------
>  include/drm/display/drm_dsc_helper.h      |   9 +
>  3 files changed, 1042 insertions(+), 396 deletions(-)

-- 
Jani Nikula, Intel Open Source Graphics Center