[Freedreno] [PATCH 02/11] drm/msm/dpu: use the actual lm maximum width instead of a hardcoded value

[Dmitry Baryshkov]

On 20/04/2023 20:47, Jeykumar Sankaran wrote:
> 
> 
> On 4/19/2023 3:23 PM, Dmitry Baryshkov wrote:
>> On 19/04/2023 17:41, Arnaud Vrac wrote:
>>> This avoids using two LMs instead of one when the display width is lower
>>> than the maximum supported value. For example on MSM8996/MSM8998, the
>>> actual maxwidth is 2560, so we would use two LMs for 1280x720 or
>>> 1920x1080 resolutions, while one is enough.
>>>
>>> Signed-off-by: Arnaud Vrac <avrac at freebox.fr>
>>
>> While this looks correct (and following what we have in 4.4), later 
>> vendor kernels specify the topology explicitly. Probably we should 
>> check this with the hw guys, because it might be the following case: 
>> even though a single LM can supply the mode, it will spend more power 
>> compared to two LMs.
>>
>>
> Yes. 2 LM split will allow the HW to run in lower mdp core clock. Can 
> you maintain the split_threshold in the hw catalog until per mode 
> topology is available?

I don't think it warrants the trouble, unless we have a real usecase 
when the device is short of LMs.

Arnaud, I'll mark this patch as Rejected for now, unless it fixes an LM 
shortage for your platform.

> 
> Jeykumar S
>>> ---
>>>   drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c | 10 +++++-----
>>>   1 file changed, 5 insertions(+), 5 deletions(-)
>>>
>>> diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c 
>>> b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c
>>> index 1dc5dbe585723..dd2914726c4f6 100644
>>> --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c
>>> +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c
>>> @@ -53,8 +53,6 @@
>>>   #define IDLE_SHORT_TIMEOUT    1
>>> -#define MAX_HDISPLAY_SPLIT 1080
>>> -
>>>   /* timeout in frames waiting for frame done */
>>>   #define DPU_ENCODER_FRAME_DONE_TIMEOUT_FRAMES 5
>>> @@ -568,10 +566,12 @@ static struct msm_display_topology 
>>> dpu_encoder_get_topology(
>>>        */
>>>       if (intf_count == 2)
>>>           topology.num_lm = 2;
>>> -    else if (!dpu_kms->catalog->caps->has_3d_merge)
>>> -        topology.num_lm = 1;
>>> +    else if (dpu_kms->catalog->caps->has_3d_merge &&
>>> +         dpu_kms->catalog->mixer_count > 0 &&
>>> +         mode->hdisplay > dpu_kms->catalog->mixer[0].sblk->maxwidth)
>>> +        topology.num_lm = 2;
>>>       else
>>> -        topology.num_lm = (mode->hdisplay > MAX_HDISPLAY_SPLIT) ? 2 
>>> : 1;
>>> +        topology.num_lm = 1;
>>>       if (crtc_state->ctm)
>>>           topology.num_dspp = topology.num_lm;
>>>
>>

-- 
With best wishes
Dmitry