[PATCH v3 1/6] drm/msm/dpu: fix video mode DSC for DSI

[Dmitry Baryshkov]

On Wed, 3 Apr 2024 at 17:44, Jun Nie <jun.nie at linaro.org> wrote:
>
> Dmitry Baryshkov <dmitry.baryshkov at linaro.org> 于2024年4月3日周三 17:57写道：
> >
> > On Wed, 3 Apr 2024 at 12:11, Jun Nie <jun.nie at linaro.org> wrote:
> > >
> > > From: Jonathan Marek <jonathan at marek.ca>
> > >
> > > Add necessary DPU timing and control changes for DSC to work with DSI
> > > video mode.
> > >
> > > Signed-off-by: Jonathan Marek <jonathan at marek.ca>
> > > Signed-off-by: Jun Nie <jun.nie at linaro.org>
> > > ---
> > >  drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c | 9 +++++++++
> > >  drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c          | 8 ++++++++
> > >  2 files changed, 17 insertions(+)
> > >
> > > diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c
> > > index d9e7dbf0499c..c7b009a60b63 100644
> > > --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c
> > > +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c
> > > @@ -115,6 +115,15 @@ static void drm_mode_to_intf_timing_params(
> > >                 timing->h_front_porch = timing->h_front_porch >> 1;
> > >                 timing->hsync_pulse_width = timing->hsync_pulse_width >> 1;
> > >         }
> > > +
> > > +       /*
> > > +        * for DSI, if compression is enabled, then divide the horizonal active
> > > +        * timing parameters by compression ratio.
> > > +        */
> > > +       if (phys_enc->hw_intf->cap->type != INTF_DP && timing->compression_en) {
> > > +               timing->width = timing->width / 3; /* XXX: don't assume 3:1 compression ratio */
> > > +               timing->xres = timing->width;
> > > +       }
> > >  }
> > >
> > >  static u32 get_horizontal_total(const struct dpu_hw_intf_timing_params *timing)
> > > diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c
> > > index 965692ef7892..079efb48db05 100644
> > > --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c
> > > +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c
> > > @@ -167,6 +167,14 @@ static void dpu_hw_intf_setup_timing_engine(struct dpu_hw_intf *ctx,
> > >                 intf_cfg2 |= INTF_CFG2_DATABUS_WIDEN;
> > >
> > >         data_width = p->width;
> > > +       if (p->wide_bus_en && !dp_intf)
> > > +               data_width = p->width >> 1;
> >
> > How is wide_bus relevant to the DSC case?
> > Is there a need for the Fixes tag?
>
> 48bit bus width should be used when DSC is enabled. Without the
> widebus configuration,
> a lot dsi error happens as below in DSC case.
> [  206.275992] dsi_err_worker: status=4

Still, separate patch please.

>
> For the Fixes tag, the previous patch mentioned to enable the widebus
> mode for any DSC case. So it is fair to add the tag.

Yes, please.

> >
> > > +
> > > +       if (p->compression_en)
> > > +               intf_cfg2 |= INTF_CFG2_DCE_DATA_COMPRESS;
> > > +
> > > +       if (p->compression_en && dp_intf)
> > > +               DPU_ERROR("missing adjustments for DSC+DP\n");
> > >
> > >         hsync_data_start_x = hsync_start_x;
> > >         hsync_data_end_x =  hsync_start_x + data_width - 1;
> > >
> > > --
> > > 2.34.1
> > >
> >
> >
> > --
> > With best wishes
> > Dmitry



-- 
With best wishes
Dmitry