[PATCH 6/9] arm64: dts: qcom: qcs6490-rb3gen2: Enable USB role switching

[Bjorn Andersson]

On Thu, Feb 22, 2024 at 01:50:12AM +0200, Dmitry Baryshkov wrote:
> On Thu, 22 Feb 2024 at 01:19, Bjorn Andersson <quic_bjorande at quicinc.com> wrote:
> >
> > With the ADSP remoteproc loaded pmic_glink can be introduced and wired
> > up to provide role and orientation switching signals.
> >
> > Signed-off-by: Bjorn Andersson <quic_bjorande at quicinc.com>
> > ---
> >  arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts | 48 +++++++++++++++++++++++++++-
> >  1 file changed, 47 insertions(+), 1 deletion(-)
> >
> > diff --git a/arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts b/arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts
> > index ab498494caea..079bf43b14cc 100644
> > --- a/arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts
> > +++ b/arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts
> > @@ -121,6 +121,41 @@ debug_vm_mem: debug-vm at d0600000 {
> >                 };
> >         };
> >
> > +       pmic-glink {
> > +               compatible = "qcom,qcm6490-pmic-glink", "qcom,pmic-glink";
> > +
> > +               #address-cells = <1>;
> > +               #size-cells = <0>;
> > +
> > +               connector at 0 {
> > +                       compatible = "usb-c-connector";
> > +                       reg = <0>;
> > +                       power-role = "dual";
> > +                       data-role = "dual";
> > +
> > +                       ports {
> > +                               #address-cells = <1>;
> > +                               #size-cells = <0>;
> > +
> > +                               port at 0 {
> > +                                       reg = <0>;
> > +
> > +                                       pmic_glink_hs_in: endpoint {
> > +                                               remote-endpoint = <&usb_1_dwc3_hs>;
> > +                                       };
> > +                               };
> > +
> > +                               port at 1 {
> > +                                       reg = <1>;
> > +
> > +                                       pmic_glink_ss_in: endpoint {
> > +                                               remote-endpoint = <&usb_1_dwc3_ss>;
> 
> This should be connected to the QMP PHY rather than to the USB host.
> 

Ahh, you're right, otherwise the orientation-switch below isn't of much
use.

> Also it might be better to squash this patch with the patch 8. Or at
> least to get redriver into the picture in this patch (and keep only
> display-related parts in that patch).
> 

The idea was to only bring in the pmic-glink here and then do the
plumbing between all the components separately, but I guess the
orientation-switch in the redriver means that it should go here as
well...

I'll shuffle this into something that makes sense.

Thanks,
Bjorn

> 
> > +                                       };
> > +                               };
> > +                       };
> > +               };
> > +       };
> > +
> >         vph_pwr: vph-pwr-regulator {
> >                 compatible = "regulator-fixed";
> >                 regulator-name = "vph_pwr";
> > @@ -476,7 +511,16 @@ &usb_1 {
> >  };
> >
> >  &usb_1_dwc3 {
> > -       dr_mode = "peripheral";
> > +       dr_mode = "otg";
> > +       usb-role-switch;
> > +};
> > +
> > +&usb_1_dwc3_hs {
> > +       remote-endpoint = <&pmic_glink_hs_in>;
> > +};
> > +
> > +&usb_1_dwc3_ss {
> > +       remote-endpoint = <&pmic_glink_ss_in>;
> >  };
> >
> >  &usb_1_hsphy {
> > @@ -491,6 +535,8 @@ &usb_1_qmpphy {
> >         vdda-phy-supply = <&vreg_l6b_1p2>;
> >         vdda-pll-supply = <&vreg_l1b_0p912>;
> >
> > +       orientation-switch;
> > +
> >         status = "okay";
> >  };
> >
> >
> > --
> > 2.25.1
> >
> 
> 
> --
> With best wishes
> Dmitry