[PATCH 2/5] phy: qcom: edp: Introduce aux_cfg array for version specific aux settings

[Soutrik Mukhopadhyay]

On 9/11/2024 4:04 PM, Dmitry Baryshkov wrote:
> On Wed, 11 Sept 2024 at 13:08, Soutrik Mukhopadhyay
> <quic_mukhopad at quicinc.com> wrote:
>> In order to support different HW versions, introduce aux_cfg array
>> to move v4 specific aux configuration settings.
>>
>> Signed-off-by: Soutrik Mukhopadhyay <quic_mukhopad at quicinc.com>
>> ---
>>   drivers/phy/qualcomm/phy-qcom-edp.c | 34 +++++++++++++++++------------
>>   1 file changed, 20 insertions(+), 14 deletions(-)
>>
>> diff --git a/drivers/phy/qualcomm/phy-qcom-edp.c b/drivers/phy/qualcomm/phy-qcom-edp.c
>> index da2b32fb5b45..0f860a807d1b 100644
>> --- a/drivers/phy/qualcomm/phy-qcom-edp.c
>> +++ b/drivers/phy/qualcomm/phy-qcom-edp.c
>> @@ -90,6 +90,7 @@ struct phy_ver_ops {
>>
>>   struct qcom_edp_phy_cfg {
>>          bool is_edp;
>> +       u8 *aux_cfg;
>>          const struct qcom_edp_swing_pre_emph_cfg *swing_pre_emph_cfg;
>>          const struct phy_ver_ops *ver_ops;
>>   };
>> @@ -186,11 +187,14 @@ static const struct qcom_edp_swing_pre_emph_cfg edp_phy_swing_pre_emph_cfg = {
>>          .pre_emphasis_hbr3_hbr2 = &edp_pre_emp_hbr2_hbr3,
>>   };
>>
>> +static u8 edp_phy_aux_cfg_v4[10] = {
> static const u8, please.


Sure, we will change this to "static const u8" in next version patch.


>
>
>> +       0x00, 0x13, 0x24, 0x00, 0x0a, 0x26, 0x0a, 0x03, 0x37, 0x03
>> +};
>> +
>>   static int qcom_edp_phy_init(struct phy *phy)
>>   {
>>          struct qcom_edp *edp = phy_get_drvdata(phy);
>>          int ret;
>> -       u8 cfg8;
>>
>>          ret = regulator_bulk_enable(ARRAY_SIZE(edp->supplies), edp->supplies);
>>          if (ret)
>> @@ -222,22 +226,20 @@ static int qcom_edp_phy_init(struct phy *phy)
>>           * even needed.
>>           */
>>          if (edp->cfg->swing_pre_emph_cfg && !edp->is_edp)
>> -               cfg8 = 0xb7;
>> -       else
>> -               cfg8 = 0x37;
>> +               edp->cfg->aux_cfg[8] = 0xb7;
>>
>>          writel(0xfc, edp->edp + DP_PHY_MODE);
>>
>> -       writel(0x00, edp->edp + DP_PHY_AUX_CFG0);
>> -       writel(0x13, edp->edp + DP_PHY_AUX_CFG1);
>> -       writel(0x24, edp->edp + DP_PHY_AUX_CFG2);
>> -       writel(0x00, edp->edp + DP_PHY_AUX_CFG3);
>> -       writel(0x0a, edp->edp + DP_PHY_AUX_CFG4);
>> -       writel(0x26, edp->edp + DP_PHY_AUX_CFG5);
>> -       writel(0x0a, edp->edp + DP_PHY_AUX_CFG6);
>> -       writel(0x03, edp->edp + DP_PHY_AUX_CFG7);
>> -       writel(cfg8, edp->edp + DP_PHY_AUX_CFG8);
>> -       writel(0x03, edp->edp + DP_PHY_AUX_CFG9);
>> +       writel(edp->cfg->aux_cfg[0], edp->edp + DP_PHY_AUX_CFG0);
>> +       writel(edp->cfg->aux_cfg[1], edp->edp + DP_PHY_AUX_CFG1);
>> +       writel(edp->cfg->aux_cfg[2], edp->edp + DP_PHY_AUX_CFG2);
>> +       writel(edp->cfg->aux_cfg[3], edp->edp + DP_PHY_AUX_CFG3);
>> +       writel(edp->cfg->aux_cfg[4], edp->edp + DP_PHY_AUX_CFG4);
>> +       writel(edp->cfg->aux_cfg[5], edp->edp + DP_PHY_AUX_CFG5);
>> +       writel(edp->cfg->aux_cfg[6], edp->edp + DP_PHY_AUX_CFG6);
>> +       writel(edp->cfg->aux_cfg[7], edp->edp + DP_PHY_AUX_CFG7);
>> +       writel(edp->cfg->aux_cfg[8], edp->edp + DP_PHY_AUX_CFG8);
>> +       writel(edp->cfg->aux_cfg[9], edp->edp + DP_PHY_AUX_CFG9);
>>
>>          writel(PHY_AUX_STOP_ERR_MASK | PHY_AUX_DEC_ERR_MASK |
>>                 PHY_AUX_SYNC_ERR_MASK | PHY_AUX_ALIGN_ERR_MASK |
>> @@ -519,16 +521,19 @@ static const struct phy_ver_ops qcom_edp_phy_ops_v4 = {
>>   };
>>
>>   static const struct qcom_edp_phy_cfg sc7280_dp_phy_cfg = {
>> +       .aux_cfg = edp_phy_aux_cfg_v4,
>>          .ver_ops = &qcom_edp_phy_ops_v4,
>>   };
>>
>>   static const struct qcom_edp_phy_cfg sc8280xp_dp_phy_cfg = {
>> +       .aux_cfg = edp_phy_aux_cfg_v4,
>>          .swing_pre_emph_cfg = &dp_phy_swing_pre_emph_cfg,
>>          .ver_ops = &qcom_edp_phy_ops_v4,
>>   };
>>
>>   static const struct qcom_edp_phy_cfg sc8280xp_edp_phy_cfg = {
>>          .is_edp = true,
>> +       .aux_cfg = edp_phy_aux_cfg_v4,
>>          .swing_pre_emph_cfg = &edp_phy_swing_pre_emph_cfg,
>>          .ver_ops = &qcom_edp_phy_ops_v4,
>>   };
>> @@ -707,6 +712,7 @@ static const struct phy_ver_ops qcom_edp_phy_ops_v6 = {
>>   };
>>
>>   static struct qcom_edp_phy_cfg x1e80100_phy_cfg = {
>> +       .aux_cfg = edp_phy_aux_cfg_v4,
> Is this correct? Judging by ver_ops, X Elite uses v6 of the PHY, so
> maybe it should also use v5 AUX tables?


As per the current implementation, v6 uses v4 aux configuration, so we 
updated it to v4.


>
>>          .swing_pre_emph_cfg = &dp_phy_swing_pre_emph_cfg,
>>          .ver_ops = &qcom_edp_phy_ops_v6,
>>   };
>> --
>> 2.17.1
>>
>
> --
> With best wishes
> Dmitry