[PATCH v3 07/10] arm64: dts: qcom: sa8775p-ride: add anx7625 DSI to DP bridge nodes

[Konrad Dybcio]

On 4/14/25 11:56 AM, Ayushi Makhija wrote:
> Hi Dmitry,
> 
> On 4/11/2025 1:31 AM, Dmitry Baryshkov wrote:
>> On Thu, Apr 10, 2025 at 06:37:54PM +0530, Ayushi Makhija wrote:
>>> Hi Dmirity/Konard
>>>
>>> On 4/7/2025 1:42 AM, Dmitry Baryshkov wrote:
>>>> On Fri, Apr 04, 2025 at 05:25:36PM +0530, Ayushi Makhija wrote:
>>>>> Add anx7625 DSI to DP bridge device nodes.

[...]

>>>>> @@ -517,9 +548,135 @@ &i2c11 {
>>>>>  
>>>>>  &i2c18 {
>>>>>  	clock-frequency = <400000>;
>>>>> -	pinctrl-0 = <&qup_i2c18_default>;
>>>>> +	pinctrl-0 = <&qup_i2c18_default>,
>>>>> +		    <&io_expander_intr_active>,
>>>>> +		    <&io_expander_reset_active>;
>>>>
>>>> These pinctrl entries should go to the IO expander itself.
>>>>
>>>>>  	pinctrl-names = "default";
>>>>> +
>>>>>  	status = "okay";
>>>>> +
>>>>> +	io_expander: gpio at 74 {
>>>>> +		compatible = "ti,tca9539";
>>>>> +		reg = <0x74>;
>>>>> +		interrupts-extended = <&tlmm 98 IRQ_TYPE_EDGE_BOTH>;
>>>>> +		gpio-controller;
>>>>> +		#gpio-cells = <2>;
>>>>> +		interrupt-controller;
>>>>> +		#interrupt-cells = <2>;
>>>>> +
>>>>> +		gpio2-hog {
>>>>
>>>> This needs a huuge explanation in the commit message. Otherwise I'd say
>>>> these pins should likely be used by the corresponding anx bridges.
>>>
>>> Thanks, for the review.
>>>
>>> Previously, I was referring to the downstream DT and misunderstood the use of gpio-hog.
>>> After reading the schematic, I realized that gpio2, gpio3, gpio10, and gpio11 are all input pins
>>> to the IO expander TC9539. We have already configured gpio2 and gpio10 as interrupts in the
>>> ANX7625 bridges, so the gpio-hog is not required. It is working without the gpio-hog configuration.
>>
>> Please make sure that there are pinctrl entries for all pins.
>>
> 
> Thanks, for the review.
> 
> While declaring the pinctrl entries inside the io_expander node, I am getting below error while checking the DTBS check against DT-binding.
> 
> Error : /local/mnt/workspace/amakhija/linux_next_11042025/linux/arch/arm64/boot/dts/qcom/sa8775p-ride.dtb: gpio at 74: 'dsi0-int-pin-state', 'dsi1-int-pin-state' do not match any of the regexes:
>         '^(hog-[0-9]+|.+-hog(-[0-9]+)?)$', 'pinctrl-[0-9]+' from schema $id: http://devicetree.org/schemas/gpio/gpio-pca95xx.yaml#
> 
>         io_expander: gpio at 74 {
>                 compatible = "ti,tca9539";
>                 reg = <0x74>;
>                 interrupts-extended = <&tlmm 98 IRQ_TYPE_EDGE_BOTH>;
>                 gpio-controller;
>                 #gpio-cells = <2>;
>                 interrupt-controller;
>                 #interrupt-cells = <2>;
> 
>                 pinctrl-0 = <&io_expander_intr_active>,
>                             <&io_expander_reset_active>;
>                 pinctrl-names = "default";
> 
>                 dsi0_int_pin: dsi0-int-pin-state {
>                         pins = "gpio2";
>                         input-enable;
>                         bias-disable;
>                 };
> 
>                 dsi1_int_pin: dsi1-int-pin-state {
>                         pins = "gpio10";
>                         input-enable;
>                         bias-disable;
>                 };
> 
>         };
> 
> I couldn't find any devicetree example of tca9539 which is using pinctrl. The gpio-pca95xx.yaml DT binding does not match with any regex of the patterns properties.

It looks like patternProperties should be extended, perhaps with
something that includes pincfg-node.yaml? Krzysztof?

Konrad