[igt-dev] [i-g-t v2 1/2] tests/kms_dither: New IGT to validate crtc Dithering
Shankar, Uma
uma.shankar at intel.com
Fri Jul 9 06:03:04 UTC 2021
> -----Original Message-----
> From: Modem, Bhanuprakash <bhanuprakash.modem at intel.com>
> Sent: Friday, July 9, 2021 5:12 PM
> To: igt-dev at lists.freedesktop.org
> Cc: Modem, Bhanuprakash <bhanuprakash.modem at intel.com>; Sharma, Swati2
> <swati2.sharma at intel.com>; Shankar, Uma <uma.shankar at intel.com>; Varide,
> Nischal <nischal.varide at intel.com>
> Subject: [i-g-t v2 1/2] tests/kms_dither: New IGT to validate crtc Dithering
>
> Many of the display devices have color format support less than the color format of
> the input data (Ex: 8-bit input data and 6-bit display color depth). Then the input data
> will be either truncated or rounded, but this approach usually causes loss of detail
> and also produce large banded areas of a single color that significantly differs from
> the original image.
>
> Dithering is a technique used to enhance these colors by creating the illusion of
> smoothness by adjusting the nearby pixel color.
> For Eg: Converting 8-bit to 6-bit by modifying the pixel information.
>
> Dithering should be enabled when a panel color depth is lower than the color depth
> of the framebuffer.
>
> Even though feature Dithering is there since legacy, there is no specific IGT for this.
> This patch will create New IGT for Dithering.
> And below is the truth table for CRTC Dithering.
>
> |----------------|---------|-------------|
> | Frame buffer | Panel | Dithering |
> |----------------|---------|-------------|
> | 8 BPC | 6 BPC | Yes |
> |----------------|---------|-------------|
> | 8 BPC | 8 BPC | No |
> |----------------|---------|-------------|
> | 8 BPC | 10 BPC | No |
> |----------------|---------|-------------|
> | 10 BPC | 6 BPC | Yes |
> |----------------|---------|-------------|
> | 10 BPC | 8 BPC | Yes |
> |----------------|---------|-------------|
> | 10 BPC | 10 BPC | No |
> |----------------|---------|-------------|
> | 16 BPC | 6 BPC | Yes |
> |----------------|---------|-------------|
> | 16 BPC | 8 BPC | Yes |
> |----------------|---------|-------------|
> | 16 BPC | 10 BPC | Yes |
> |----------------|---------|-------------|
>
> Note: As i915 enables dithering for 6 bpc panels only, we need to limit the execution
> to 6 & 8 bpc panels (Negative testing) only.
>
> Cc: Swati Sharma <swati2.sharma at intel.com>
> Cc: Uma Shankar <uma.shankar at intel.com>
> Cc: Nischal Varide <nischal.varide at intel.com>
> Signed-off-by: Bhanuprakash Modem <bhanuprakash.modem at intel.com>
> ---
> tests/kms_dither.c | 242 +++++++++++++++++++++++++++++++++++++++++++++
> tests/meson.build | 1 +
> 2 files changed, 243 insertions(+)
> create mode 100644 tests/kms_dither.c
>
> diff --git a/tests/kms_dither.c b/tests/kms_dither.c new file mode 100644 index
> 000000000..50c649ca8
> --- /dev/null
> +++ b/tests/kms_dither.c
> @@ -0,0 +1,242 @@
> +/*
> + * Copyright © 2020 Intel Corporation
> + *
> + * Permission is hereby granted, free of charge, to any person
> +obtaining a
> + * copy of this software and associated documentation files (the
> +"Software"),
> + * to deal in the Software without restriction, including without
> +limitation
> + * the rights to use, copy, modify, merge, publish, distribute,
> +sublicense,
> + * and/or sell copies of the Software, and to permit persons to whom
> +the
> + * Software is furnished to do so, subject to the following conditions:
> + *
> + * The above copyright notice and this permission notice (including the
> +next
> + * paragraph) shall be included in all copies or substantial portions
> +of the
> + * Software.
> + *
> + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> +EXPRESS OR
> + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF
> +MERCHANTABILITY,
> + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT
> +SHALL
> + * THE COPYRIGHT HOLDER(S) OR AUTHOR(S) BE LIABLE FOR ANY CLAIM,
> +DAMAGES OR
> + * OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR
> +OTHERWISE,
> + * ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE
> +OR
> + * OTHER DEALINGS IN THE SOFTWARE.
> + *
> + * Authors:
> + * Bhanuprakash Modem <bhanuprakash.modem at intel.com>
> + *
> + */
> +
> +#include "igt.h"
> +#include <fcntl.h>
> +#include <termios.h>
> +#include <unistd.h>
> +
> +IGT_TEST_DESCRIPTION("Test Dithering block status");
> +
> +/* Connector BPC */
> +#define IGT_CONNECTOR_BPC_6 6
> +#define IGT_CONNECTOR_BPC_8 8
> +
> +/* Framebuffer BPC */
> +#define IGT_FRAME_BUFFER_BPC_8 8
> +
> +/* Common test data. */
> +typedef struct data {
> + igt_display_t display;
> + igt_plane_t *primary;
> + igt_output_t *output;
> + igt_pipe_t *pipe;
> + drmModeModeInfo *mode;
> + enum pipe pipe_id;
> + int drm_fd;
> + igt_fb_t fb;
> +} data_t;
> +
> +typedef struct {
> + unsigned int bpc;
> + unsigned int dither;
> +} dither_status_t;
> +
> +/* Prepare test data. */
> +static void prepare_test(data_t *data, igt_output_t *output, enum pipe
> +pipe) {
> + igt_display_t *display = &data->display;
> +
> + data->pipe_id = pipe;
> + data->pipe = &data->display.pipes[data->pipe_id];
> + igt_assert(data->pipe);
> +
> + igt_display_reset(display);
> +
> + data->output = output;
> + igt_assert(data->output);
> +
> + data->mode = igt_output_get_mode(data->output);
> + igt_assert(data->mode);
> +
> + data->primary =
> + igt_pipe_get_plane_type(data->pipe,
> DRM_PLANE_TYPE_PRIMARY);
> +
> + igt_output_set_pipe(data->output, data->pipe_id); }
> +
> +/* Returns the current state of dithering from the crtc debugfs. */
> +static dither_status_t get_dither_state(data_t *data) {
> + char buf[512], tmp[5];
> + char *start_loc;
> + int dir, res;
> + dither_status_t status;
> +
> + dir = igt_debugfs_dir(data->drm_fd);
> + igt_assert(dir >= 0);
> +
> + res = igt_debugfs_simple_read(dir, "i915_display_info", buf, sizeof(buf));
> + igt_require(res > 0);
> + close(dir);
> +
> + igt_assert(start_loc = strstr(buf, ", bpp="));
> + igt_assert_eq(sscanf(start_loc, ", bpp=%u", &status.bpc), 1);
> + status.bpc /= 3;
> +
> + igt_assert(start_loc = strstr(buf, ", dither="));
> + igt_assert_eq(sscanf(start_loc, ", dither=%s", tmp), 1);
> + status.dither = !strcmp(tmp, "yes,");
> +
> + return status;
> +}
> +
> +static void test_dithering(data_t *data, enum pipe pipe,
> + igt_output_t *output,
> + int fb_bpc, int fb_format,
> + int output_bpc)
> +{
> + igt_display_t *display = &data->display;
> + dither_status_t status;
> + int bpc = 0;
> +
> + igt_info("Dithering test execution on %s PIPE_%s\n",
> + output->name, kmstest_pipe_name(pipe));
> + prepare_test(data, output, pipe);
> +
> + igt_assert(igt_create_fb(data->drm_fd, data->mode->hdisplay,
> + data->mode->vdisplay, fb_format,
> + LOCAL_DRM_FORMAT_MOD_NONE, &data->fb));
> + igt_plane_set_fb(data->primary, &data->fb);
> + igt_plane_set_size(data->primary, data->mode->hdisplay,
> +data->mode->vdisplay);
> +
> + if (igt_output_has_prop(output, IGT_CONNECTOR_MAX_BPC)) {
> + bpc = igt_output_get_prop(output, IGT_CONNECTOR_MAX_BPC);
You can have these has_prop as igt_require before going further in the tests and skip in case
we don't get them.
> + igt_output_set_prop_value(data->output,
> IGT_CONNECTOR_MAX_BPC, output_bpc);
> + }
> + igt_display_commit2(display, display->is_atomic ? COMMIT_ATOMIC :
> +COMMIT_LEGACY);
> +
> + /*
> + * Check the status of Dithering block:
> + *
> + * Preserve the result & compute later (after clean-up).
> + * If fb_bpc is greater than output_bpc, Dithering should be enabled
> + * Else disabled
> + */
> + status = get_dither_state(data);
> +
> + igt_info("FB BPC:%d, Panel BPC:%d, Pipe BPC:%d, Expected Dither:%s,
> Actual result:%s\n",
> + fb_bpc, output_bpc, status.bpc,
> + (fb_bpc > output_bpc) ? "Enable": "Disable",
> + status.dither ? "Enable": "Disable");
> +
> + /*
> + * We must update the Connector max_bpc property back
> + * Otherwise, previously updated value will stay forever and
> + * may cause the failures for next/other subtests.
> + */
> + if (bpc)
> + igt_output_set_prop_value(data->output,
> IGT_CONNECTOR_MAX_BPC, bpc);
> + igt_plane_set_fb(data->primary, NULL);
> + igt_output_set_pipe(output, PIPE_NONE);
> + igt_display_commit2(display, display->is_atomic ? COMMIT_ATOMIC :
> COMMIT_LEGACY);
> + igt_remove_fb(data->drm_fd, &data->fb);
> +
> + /* Check if crtc bpc is updated with requested one. */
> + igt_require_f((status.bpc == output_bpc),
> + "%s can support max %u-bpc, but requested %d-bpc\n",
> + output->name, status.bpc, output_bpc);
> +
> + /* Compute the result. */
> + if (fb_bpc > output_bpc)
> + igt_assert_f(status.dither, "(fb_%dbpc > output_%dbpc): Dither
> should be enabled\n",
> + fb_bpc, output_bpc);
> + else
> + igt_assert_f(!status.dither, "(fb_%dbpc <= output_%dbpc): Dither
> should be disabled\n",
> + fb_bpc, output_bpc);
> +
> + return;
> +}
> +
> +static void
> +run_dither_test(data_t *data, int fb_bpc, int fb_format, int
> +output_bpc) {
> + igt_output_t *output;
> + igt_display_t *display = &data->display;
> +
> + for_each_connected_output(display, output) {
> + enum pipe pipe;
> + drmModeConnector *connector = output->config.connector;
> +
> + /* HDMI won't support 6 BPC */
> + if (output_bpc == IGT_CONNECTOR_BPC_6 &&
> + (connector->connector_type ==
> DRM_MODE_CONNECTOR_HDMIA ||
> + connector->connector_type ==
> DRM_MODE_CONNECTOR_HDMIB))
I think we already have a check in test_dithering, so we can drop this specific
encoder check here.
> + continue;
> +
> + for_each_pipe(display, pipe) {
> + if (igt_pipe_connector_valid(pipe, output)) {
> + igt_dynamic_f("%s-pipe-%s", output->name,
> kmstest_pipe_name(pipe))
> + test_dithering(data, pipe, output, fb_bpc,
> + fb_format, output_bpc);
> +
> + /* One pipe is enough */
> + break;
> + }
> + }
> + }
> +}
> +
> +igt_main
> +{
> + struct {
> + int fb_bpc;
> + int format;
> + int output_bpc;
> + } tests[] = {
> + { IGT_FRAME_BUFFER_BPC_8, DRM_FORMAT_XRGB8888,
> IGT_CONNECTOR_BPC_6 },
> + { IGT_FRAME_BUFFER_BPC_8, DRM_FORMAT_XRGB8888,
> IGT_CONNECTOR_BPC_8 },
> + };
> + int i;
> + data_t data = { 0 };
> +
> + igt_fixture {
> + data.drm_fd = drm_open_driver_master(DRIVER_INTEL);
> + kmstest_set_vt_graphics_mode();
> +
> + igt_display_require(&data.display, data.drm_fd);
> + igt_display_require_output(&data.display);
> + }
> +
> + for (i = 0; i < ARRAY_SIZE(tests); i++) {
> + igt_describe_f("Framebuffer BPC:%d, Panel BPC:%d, Expected
> Dither:%s\n",
> + tests[i].fb_bpc, tests[i].output_bpc,
> + (tests[i].fb_bpc > tests[i].output_bpc) ?
> + "Enable": "Disable");
> +
> + igt_subtest_with_dynamic_f("FB-%dBPC-Vs-Panel-%dBPC",
> + tests[i].fb_bpc, tests[i].output_bpc)
> + run_dither_test(&data,
> + tests[i].fb_bpc,
> + tests[i].format,
> + tests[i].output_bpc);
> + }
> +
> + igt_fixture {
> + igt_display_fini(&data.display);
> + }
> +}
> diff --git a/tests/meson.build b/tests/meson.build index 01911c457..d3de40be0
> 100644
> --- a/tests/meson.build
> +++ b/tests/meson.build
> @@ -29,6 +29,7 @@ test_progs = [
> 'kms_cursor_crc',
> 'kms_cursor_edge_walk',
> 'kms_cursor_legacy',
> + 'kms_dither',
> 'kms_dp_aux_dev',
> 'kms_dp_dsc',
> 'kms_dp_tiled_display',
> --
> 2.20.1
More information about the igt-dev
mailing list