[igt-dev] [PATCH] tests/kms_atomic: Match overlay size with primary plane on amdgpu

[Mark Yacoub]

From: Mark Yacoub <markyacoub at google.com>

[Why]
AMDGPU has a restriction of not allowing overlay planes that do
not fully cover the primary plane when the cursor is enabled.
Testing with an overlay smaller than primary fails the commit.

[How]
On amdgpu, force the overlay size and src to match the primary plane, but
test with a smaller size on all other platforms.

Signed-off-by: markyacoub at chromium.org
Change-Id: I48204b467e03312a2fc9700d1a079ecc35d53670
---
 tests/kms_atomic.c | 26 ++++++++++++++++++++------
 1 file changed, 20 insertions(+), 6 deletions(-)

diff --git a/tests/kms_atomic.c b/tests/kms_atomic.c
index df9c9df7..4ab8b207 100644
--- a/tests/kms_atomic.c
+++ b/tests/kms_atomic.c
@@ -491,13 +491,27 @@ plane_immutable_zpos(igt_display_t *display, igt_pipe_t *pipe,
 	igt_remove_fb(display->drm_fd, &fb_upper);
 }
 
-static void plane_overlay(igt_pipe_t *pipe, igt_output_t *output, igt_plane_t *plane)
+static void plane_overlay(igt_pipe_t* pipe, igt_output_t* output, igt_plane_t* plane, int drm_fd)
 {
 	drmModeModeInfo *mode = igt_output_get_mode(output);
 	uint32_t format = plane_get_igt_format(plane);
 	struct igt_fb fb;
-	uint32_t w = mode->hdisplay / 2;
-	uint32_t h = mode->vdisplay / 2;
+	uint32_t w, h, x, y;
+
+	// On AMD, with hardware cursor, overlay plane must fully cover the primary plane.
+	// Test with smaller overlays on all other platforms.
+	if (is_amdgpu_device(drm_fd)) {
+		w = mode->hdisplay;
+		h = mode->vdisplay;
+		x = 0;
+		y = 0;
+	}
+	else {
+		w = mode->hdisplay / 2;
+		h = mode->vdisplay / 2;
+		x = w / 2;
+		y = h / 2;
+	}
 
 	igt_require(format != 0);
 
@@ -505,7 +519,7 @@ static void plane_overlay(igt_pipe_t *pipe, igt_output_t *output, igt_plane_t *p
 			      format, I915_TILING_NONE, &fb);
 
 	igt_plane_set_fb(plane, &fb);
-	igt_plane_set_position(plane, w/2, h/2);
+	igt_plane_set_position(plane, x, y);
 
 	/* Enable the overlay plane using the atomic API, and double-check
 	 * state is what we think it should be. */
@@ -519,7 +533,7 @@ static void plane_overlay(igt_pipe_t *pipe, igt_output_t *output, igt_plane_t *p
 	/* Re-enable the plane through the legacy plane API, and verify through
 	 * atomic. */
 	igt_plane_set_fb(plane, &fb);
-	igt_plane_set_position(plane, w/2, h/2);
+	igt_plane_set_position(plane, x, y);
 	plane_commit(plane, COMMIT_LEGACY, ATOMIC_RELAX_NONE);
 
 	/* Restore the plane to its original settings through the legacy plane
@@ -1113,7 +1127,7 @@ igt_main
 		igt_require(overlay);
 
 		atomic_setup(&display, pipe, output, primary, &fb);
-		plane_overlay(pipe_obj, output, overlay);
+		plane_overlay(pipe_obj, output, overlay, display.drm_fd);
 	}
 
 	igt_describe("Test for KMS atomic modesetting on primary plane and ensure coherency between "
-- 
2.31.1.818.g46aad6cb9e-goog