[igt-dev] [i-g-t v5 04/52] tests/kms_atomic: Add support for Bigjoiner

[Bhanuprakash Modem]

This patch will add a check to Skip the subtest if a selected pipe/output
combo won't support Bigjoiner or 8K mode.

Example:
* Pipe-D wont support a mode > 5K
* To use 8K mode on a pipe then consecutive pipe must be available & free.

V2: - Use updated helper name

Signed-off-by: Bhanuprakash Modem <bhanuprakash.modem at intel.com>
---
 tests/kms_atomic.c | 32 ++++++++++++++++++++++++++++----
 1 file changed, 28 insertions(+), 4 deletions(-)

diff --git a/tests/kms_atomic.c b/tests/kms_atomic.c
index 2a3fb74b..61117a3f 100644
--- a/tests/kms_atomic.c
+++ b/tests/kms_atomic.c
@@ -1265,6 +1265,10 @@ static void atomic_plane_damage(igt_pipe_t *pipe, igt_plane_t *plane, struct igt
 
 static void atomic_setup(igt_display_t *display, enum pipe pipe, igt_output_t *output, igt_plane_t *primary, struct igt_fb *fb)
 {
+	igt_info("Using (pipe %s + %s) to run the subtest.\n",
+		 kmstest_pipe_name(pipe), igt_output_name(output));
+
+	igt_display_reset(display);
 	igt_output_set_pipe(output, pipe);
 	igt_plane_set_fb(primary, fb);
 
@@ -1293,6 +1297,7 @@ igt_main
 	igt_plane_t *primary = NULL;
 	drmModeModeInfo *mode;
 	struct igt_fb fb;
+	bool valid_config = false;
 
 	igt_fixture {
 		display.drm_fd = drm_open_driver_master(DRIVER_ANY);
@@ -1303,8 +1308,16 @@ igt_main
 		igt_require(display.is_atomic);
 		igt_display_require_output(&display);
 
-		for_each_pipe_with_valid_output(&display, pipe, output)
-			break;
+		for_each_pipe_with_valid_output(&display, pipe, output) {
+			igt_display_reset(&display);
+
+			igt_output_set_pipe(output, pipe);
+			if (i915_pipe_output_combo_valid(&display)) {
+				valid_config = true;
+				break;
+			}
+		}
+		igt_require(valid_config);
 
 		pipe_obj = &display.pipes[pipe];
 		primary = igt_pipe_get_plane_type(pipe_obj, DRM_PLANE_TYPE_PRIMARY);
@@ -1342,9 +1355,13 @@ igt_main
 	igt_subtest("plane-primary-overlay-mutable-zpos") {
 		uint32_t format_primary = DRM_FORMAT_ARGB8888;
 		uint32_t format_overlay = DRM_FORMAT_ARGB1555;
+		igt_plane_t *overlay;
 
-		igt_plane_t *overlay =
-			igt_pipe_get_plane_type(pipe_obj, DRM_PLANE_TYPE_OVERLAY);
+		igt_info("Using (pipe %s + %s) to run the subtest.\n",
+			 kmstest_pipe_name(pipe), igt_output_name(output));
+
+		igt_display_reset(&display);
+		overlay = igt_pipe_get_plane_type(pipe_obj, DRM_PLANE_TYPE_OVERLAY);
 		igt_require(overlay);
 
 		igt_require(igt_plane_has_prop(primary, IGT_PLANE_ZPOS));
@@ -1361,6 +1378,10 @@ igt_main
 	igt_describe("Verify the reported zpos property of planes by making sure "\
 		     "only higher zpos planes cover the lower zpos ones.");
 	igt_subtest("plane-immutable-zpos") {
+		igt_info("Using (pipe %s + %s) to run the subtest.\n",
+			 kmstest_pipe_name(pipe), igt_output_name(output));
+
+		igt_display_reset(&display);
 		igt_output_set_pipe(output, pipe);
 		plane_immutable_zpos(&display, pipe_obj, output);
 	}
@@ -1370,6 +1391,9 @@ igt_main
 	igt_subtest("test-only") {
 		atomic_clear(&display, pipe, primary, output);
 
+		igt_info("Using (pipe %s + %s) to run the subtest.\n",
+			 kmstest_pipe_name(pipe), igt_output_name(output));
+
 		test_only(pipe_obj, primary, output);
 	}
 
-- 
2.38.0