[igt-dev] [PATCH i-g-t 1/3] tests/perf_pmu: Compare against requested freq in frequency subtest

[Tvrtko Ursulin]

On 15/02/2023 04:02, Dixit, Ashutosh wrote:
> On Wed, 11 Jan 2023 01:54:59 -0800, Tvrtko Ursulin wrote:
>>
> 
> Hi Tvrtko,
> 
> Sorry I completely missed your reply and only just saw it again. People
> needing a recap of the previous discussion can see it here:
> 
> https://patchwork.freedesktop.org/patch/512274/?series=110574&rev=3#comment_933447
> 
>> On 10/01/2023 19:47, Ashutosh Dixit wrote:
>>> After the i915 commit 95ccf312a1e4f ("drm/i915/guc/slpc: Allow SLPC to use
>>> efficient frequency"), FW uses the requested freq as the efficient freq
>>> which can exceed the max freq set. Therefore, in the "min freq" part of the
>>> igt at perf_pmu@frequency subtest, compare the requested freq reported by PMU
>>> not against the set freq but against the requested freq reported in sysfs.
>>>
>>> v2: Remove previously added delays. GuC FW is now updated to set min/max
>>>       freq in top half so delays are not needed
>>> v3: Increase tolerance between measured and requested freq to 10% to
>>>       account for sporadic failures due to dynamically changing efficient
>>>       freq. Also document the changes in code.
>>>
>>> Bug: https://gitlab.freedesktop.org/drm/intel/-/issues/6806
>>> Signed-off-by: Ashutosh Dixit <ashutosh.dixit at intel.com>
>>> ---
>>>    tests/i915/perf_pmu.c | 12 ++++++++++--
>>>    1 file changed, 10 insertions(+), 2 deletions(-)
>>>
>>> diff --git a/tests/i915/perf_pmu.c b/tests/i915/perf_pmu.c
>>> index f363db2ba13..f9ef89fb0b3 100644
>>> --- a/tests/i915/perf_pmu.c
>>> +++ b/tests/i915/perf_pmu.c
>>> @@ -1546,7 +1546,7 @@ test_interrupts_sync(int gem_fd)
>>>    static void
>>>    test_frequency(int gem_fd)
>>>    {
>>> -	uint32_t min_freq, max_freq, boost_freq;
>>> +	uint32_t min_freq, max_freq, boost_freq, min_req;
>>> 	uint64_t val[2], start[2], slept;
>>> 	double min[2], max[2];
>>> 	igt_spin_t *spin;
>>> @@ -1587,6 +1587,7 @@ test_frequency(int gem_fd)
>>> 		min[0] = 1e9*(val[0] - start[0]) / slept;
>>> 	min[1] = 1e9*(val[1] - start[1]) / slept;
>>> +	min_req = igt_sysfs_get_u32(sysfs, "gt_cur_freq_mhz");
>>
>> So remove all of the above three igt_sysfs_set_u32 and test still passes
>> right? What it is testing then?
> 
> Yes, so since enabling efficient freq (RPe) has broken the kernel ABI was
> cannot test that the PMU measured freq is min_freq. All we can do, fwiw, is
> test that the PMU measured freq matches the freq exposed via the sysfs
> interface (min_req) at this "min point".
> 
> I believe what I was saying when we last discussed this was that we can
> have two sets of tests:
> 
> 1. Current tests with RPe enabled
> 2. Expose a sysfs from i915 to disable RPe and then use that to go to the
>     previous versions of the tests here
> 
> So these patches are for case 1.
> 
> Now about 2., considering that we are moving to the xe driver soon, I am
> wondering if there is much ROI in exposing the RPe disabling sysfs from
> i915. We might as well do something like that in xe? Or should this still
> be done in i915?
> 
> In any case, there is interest in closing out these two bugs if possible:
> 
> Bug: https://gitlab.freedesktop.org/drm/intel/-/issues/6806
> Bug: https://gitlab.freedesktop.org/drm/intel/-/issues/6786
> 
> If we are not going to merge these patches (and assuming we won't change
> i915), how about just saying that due to change in the kernel ABI these
> tests are no longer valid and therefore blocklisting these tests and
> closing the bugs as 'will not fix'?

How about we drop any notion of min/max from the test and just check 
that the PMU sees what sysfs sees? Once with idle, once with busy 
(frequency-idle, frequency-busy; via TEST_BUSY/!TEST_BUSY). Would that 
work and be acceptable?

Regards,

Tvrtko