[PATCH i-g-t v2] tests/intel/xe_gt_freq: Add a wait after gt reset

[Riana Tauro]

Hi Karthik

It's better to split patches. One for rename and another for wait after 
gt reset.

Thanks,
Riana

On 8/9/2024 9:10 PM, Karthik Poosa wrote:
> After reset min and max takes sometime to get set.
> So add a wait of 100ms after gt reset before reading
> min and max frequencies.
> 
> v2:
>   - Rename ACT_FREQ_LATENCY_US to SLPC_FREQ_LATENCY_US and use it
>     instead of new macro. (Riana)
> 
> Signed-off-by: Karthik Poosa <karthik.poosa at intel.com>
> ---
>   tests/intel/xe_gt_freq.c | 17 +++++++++--------
>   1 file changed, 9 insertions(+), 8 deletions(-)
> 
> diff --git a/tests/intel/xe_gt_freq.c b/tests/intel/xe_gt_freq.c
> index 171f9cb44..427e12c55 100644
> --- a/tests/intel/xe_gt_freq.c
> +++ b/tests/intel/xe_gt_freq.c
> @@ -34,7 +34,7 @@
>    * Too many intermediate components and steps before freq is adjusted
>    * Specially if workload is under execution, so let's wait 100 ms.
>    */
> -#define ACT_FREQ_LATENCY_US 100000
> +#define SLPC_FREQ_LATENCY_US 100000
>   
>   static int set_freq(int fd, int gt_id, const char *freq_name, uint32_t freq)
>   {
> @@ -194,7 +194,7 @@ static void test_freq_fixed(int fd, int gt_id, bool gt_idle)
>   	 */
>   	igt_assert_lt(0, set_freq(fd, gt_id, "min", rpn));
>   	igt_assert_lt(0, set_freq(fd, gt_id, "max", rpn));
> -	usleep(ACT_FREQ_LATENCY_US);
> +	usleep(SLPC_FREQ_LATENCY_US);
>   	igt_assert_eq_u32(get_freq(fd, gt_id, "cur"), rpn);
>   
>   	if (gt_idle) {
> @@ -208,7 +208,7 @@ static void test_freq_fixed(int fd, int gt_id, bool gt_idle)
>   
>   	igt_assert_lt(0, set_freq(fd, gt_id, "min", rpmid));
>   	igt_assert_lt(0, set_freq(fd, gt_id, "max", rpmid));
> -	usleep(ACT_FREQ_LATENCY_US);
> +	usleep(SLPC_FREQ_LATENCY_US);
>   	cur_freq = get_freq(fd, gt_id, "cur");
>   	/* If rpmid is around RPe, we could see SLPC follow it */
>   	igt_assert_lte_u32((rpmid - FREQ_UNIT_MHZ), cur_freq);
> @@ -224,7 +224,7 @@ static void test_freq_fixed(int fd, int gt_id, bool gt_idle)
>   
>   	igt_assert_lt(0, set_freq(fd, gt_id, "min", rp0));
>   	igt_assert_lt(0, set_freq(fd, gt_id, "max", rp0));
> -	usleep(ACT_FREQ_LATENCY_US);
> +	usleep(SLPC_FREQ_LATENCY_US);
>   	/*
>   	 * It is unlikely that PCODE will *always* respect any request above RPe
>   	 * So for this level let's only check if GuC PC is doing its job
> @@ -259,7 +259,7 @@ static void test_freq_range(int fd, int gt_id, bool gt_idle)
>   
>   	igt_assert_lt(0, set_freq(fd, gt_id, "min", rpn));
>   	igt_assert_lt(0, set_freq(fd, gt_id, "max", rpmid));
> -	usleep(ACT_FREQ_LATENCY_US);
> +	usleep(SLPC_FREQ_LATENCY_US);
>   	cur = get_freq(fd, gt_id, "cur");
>   	igt_assert(rpn <= cur && cur <= rpmid + FREQ_UNIT_MHZ);
>   
> @@ -292,7 +292,7 @@ static void test_freq_low_max(int fd, int gt_id)
>   	 */
>   	igt_assert_lt(0, set_freq(fd, gt_id, "min", rpmid));
>   	igt_assert_lt(0, set_freq(fd, gt_id, "max", rpn));
> -	usleep(ACT_FREQ_LATENCY_US);
> +	usleep(SLPC_FREQ_LATENCY_US);
>   
>   	/* Cur freq will follow RPe, which could be higher than min freq */
>   	igt_assert_lte_u32((rpmid - FREQ_UNIT_MHZ),
> @@ -310,7 +310,7 @@ static void test_suspend(int fd, int gt_id)
>   
>   	igt_assert_lt(0, set_freq(fd, gt_id, "min", rpn));
>   	igt_assert_lt(0, set_freq(fd, gt_id, "max", rpn));
> -	usleep(ACT_FREQ_LATENCY_US);
> +	usleep(SLPC_FREQ_LATENCY_US);
>   	igt_assert_eq_u32(get_freq(fd, gt_id, "cur"), rpn);
>   
>   	igt_system_suspend_autoresume(SUSPEND_STATE_S3,
> @@ -337,11 +337,12 @@ static void test_reset(int fd, int gt_id, int cycles)
>   			     "Failed after %d good cycles\n", i);
>   		igt_assert_f(set_freq(fd, gt_id, "max", rpn) > 0,
>   			     "Failed after %d good cycles\n", i);
> -		usleep(ACT_FREQ_LATENCY_US);
> +		usleep(SLPC_FREQ_LATENCY_US);
>   		igt_assert_f(get_freq(fd, gt_id, "cur") == rpn,
>   			     "Failed after %d good cycles\n", i);
>   
>   		xe_force_gt_reset_async(fd, gt_id);
> +		usleep(SLPC_FREQ_LATENCY_US);
>   
>   		igt_assert_f(get_freq(fd, gt_id, "min") == rpn,
>   			     "Failed after %d good cycles\n", i);