[PATCH libevdev 4/4] doc: move the section for the internal test suite down

[Peter Hutterer]

"Related Pages" in doxygen are ordered in the order they appear in the source
file. The internal test suite is least likely to be of interest to the
reader, so move it to the bottom.

Signed-off-by: Peter Hutterer <peter.hutterer at who-t.net>
---
 libevdev/libevdev.h | 92 ++++++++++++++++++++++++++---------------------------
 1 file changed, 46 insertions(+), 46 deletions(-)

diff --git a/libevdev/libevdev.h b/libevdev/libevdev.h
index d5c7515..8cf7764 100644
--- a/libevdev/libevdev.h
+++ b/libevdev/libevdev.h
@@ -309,52 +309,6 @@ extern "C" {
  */
 
 /**
- * @page testing libevdev-internal test suite
- *
- * libevdev's internal test suite uses the
- * [Check unit testing framework](http://check.sourceforge.net/). Tests are
- * divided into test suites and test cases. Most tests create a uinput device,
- * so you'll need to run as root.
- *
- * To run a specific suite only:
- *
- *     export CK_RUN_SUITE="suite name"
- *
- * To run a specific test case only:
- *
- *     export CK_RUN_TEST="test case name"
- *
- * To get a list of all suites or tests:
- *
- *     git grep "suite_create"
- *     git grep "tcase_create"
- *
- * By default, Check forks, making debugging harder. The test suite tries to detect
- * if it is running inside gdb and disable forking. If that doesn't work for
- * some reason, run gdb as below to avoid forking.
- *
- *     sudo CK_FORK=no CK_RUN_TEST="test case name" gdb ./test/test-libevdev
- *
- * A special target `make gcov-report.txt` exists that runs gcov and leaves a
- * `libevdev.c.gcov` file. Check that for test coverage.
- *
- * `make check` is hooked up to run the test and gcov (again, needs root).
- *
- * The test suite creates a lot of devices, very quickly. Add the following
- * xorg.conf.d snippet to avoid the devices being added as X devices (at the
- * time of writing, mutter can't handle these devices and exits after getting
- * a BadDevice error).
- *
- *     $ cat /etc/X11/xorg.conf.d/99-ignore-libevdev-devices.conf
- *     Section "InputClass"
- *             Identifier "Ignore libevdev test devices"
- *             MatchProduct "libevdev test device"
- *             Option "Ignore" "on"
- *     EndSection
- *
- */
-
-/**
  * @page backwardscompatibility Compatibility and Behavior across kernel versions
  *
  * This page describes libevdev's behavior when the build-time kernel and the
@@ -478,6 +432,52 @@ extern "C" {
  */
 
 /**
+ * @page testing libevdev-internal test suite
+ *
+ * libevdev's internal test suite uses the
+ * [Check unit testing framework](http://check.sourceforge.net/). Tests are
+ * divided into test suites and test cases. Most tests create a uinput device,
+ * so you'll need to run as root.
+ *
+ * To run a specific suite only:
+ *
+ *     export CK_RUN_SUITE="suite name"
+ *
+ * To run a specific test case only:
+ *
+ *     export CK_RUN_TEST="test case name"
+ *
+ * To get a list of all suites or tests:
+ *
+ *     git grep "suite_create"
+ *     git grep "tcase_create"
+ *
+ * By default, Check forks, making debugging harder. The test suite tries to detect
+ * if it is running inside gdb and disable forking. If that doesn't work for
+ * some reason, run gdb as below to avoid forking.
+ *
+ *     sudo CK_FORK=no CK_RUN_TEST="test case name" gdb ./test/test-libevdev
+ *
+ * A special target `make gcov-report.txt` exists that runs gcov and leaves a
+ * `libevdev.c.gcov` file. Check that for test coverage.
+ *
+ * `make check` is hooked up to run the test and gcov (again, needs root).
+ *
+ * The test suite creates a lot of devices, very quickly. Add the following
+ * xorg.conf.d snippet to avoid the devices being added as X devices (at the
+ * time of writing, mutter can't handle these devices and exits after getting
+ * a BadDevice error).
+ *
+ *     $ cat /etc/X11/xorg.conf.d/99-ignore-libevdev-devices.conf
+ *     Section "InputClass"
+ *             Identifier "Ignore libevdev test devices"
+ *             MatchProduct "libevdev test device"
+ *             Option "Ignore" "on"
+ *     EndSection
+ *
+ */
+
+/**
  * @defgroup init Initialization and setup
  *
  * Initialization, initial setup and file descriptor handling.
-- 
1.8.5.3