[PATCH 2/2] fls
Chris Wilson
chris at chris-wilson.co.uk
Fri Mar 5 12:46:07 UTC 2021
---
drivers/gpu/drm/i915/gt/intel_workarounds.c | 146 ++++++++++----------
1 file changed, 74 insertions(+), 72 deletions(-)
diff --git a/drivers/gpu/drm/i915/gt/intel_workarounds.c b/drivers/gpu/drm/i915/gt/intel_workarounds.c
index 3b4a7da60f0b..3068135fb53a 100644
--- a/drivers/gpu/drm/i915/gt/intel_workarounds.c
+++ b/drivers/gpu/drm/i915/gt/intel_workarounds.c
@@ -878,9 +878,83 @@ hsw_gt_workarounds_init(struct drm_i915_private *i915, struct i915_wa_list *wal)
wa_write_clr(wal, GEN7_FF_THREAD_MODE, GEN7_FF_VS_REF_CNT_FFME);
}
+static void
+wa_init_mcr(struct drm_i915_private *i915, struct i915_wa_list *wal)
+{
+ const struct sseu_dev_info *sseu = &i915->gt.info.sseu;
+ unsigned int slice, subslice;
+ u32 l3_en, mcr, mcr_mask;
+
+ GEM_BUG_ON(INTEL_GEN(i915) < 9);
+
+ /*
+ * WaProgramMgsrForL3BankSpecificMmioReads: cnl,icl
+ * L3Banks could be fused off in single slice scenario. If that is
+ * the case, we might need to program MCR select to a valid L3Bank
+ * by default, to make sure we correctly read certain registers
+ * later on (in the range 0xB100 - 0xB3FF).
+ *
+ * WaProgramMgsrForCorrectSliceSpecificMmioReads:cnl,icl
+ * Before any MMIO read into slice/subslice specific registers, MCR
+ * packet control register needs to be programmed to point to any
+ * enabled s/ss pair. Otherwise, incorrect values will be returned.
+ * This means each subsequent MMIO read will be forwarded to an
+ * specific s/ss combination, but this is OK since these registers
+ * are consistent across s/ss in almost all cases. In the rare
+ * occasions, such as INSTDONE, where this value is dependent
+ * on s/ss combo, the read should be done with read_subslice_reg.
+ *
+ * Since GEN8_MCR_SELECTOR contains dual-purpose bits which select both
+ * to which subslice, or to which L3 bank, the respective mmio reads
+ * will go, we have to find a common index which works for both
+ * accesses.
+ *
+ * Case where we cannot find a common index fortunately should not
+ * happen in production hardware, so we only emit a warning instead of
+ * implementing something more complex that requires checking the range
+ * of every MMIO read.
+ */
+
+ if (INTEL_GEN(i915) >= 10 && is_power_of_2(sseu->slice_mask)) {
+ u32 l3_fuse =
+ intel_uncore_read(&i915->uncore, GEN10_MIRROR_FUSE3) &
+ GEN10_L3BANK_MASK;
+
+ drm_dbg(&i915->drm, "L3 fuse = %x\n", l3_fuse);
+ l3_en = ~(l3_fuse << GEN10_L3BANK_PAIR_COUNT | l3_fuse);
+ } else {
+ l3_en = ~0;
+ }
+
+ slice = fls(sseu->slice_mask) - 1;
+ subslice = fls(l3_en & intel_sseu_get_subslices(sseu, slice));
+ if (!subslice) {
+ drm_warn(&i915->drm,
+ "No common index found between subslice mask %x and L3 bank mask %x!\n",
+ intel_sseu_get_subslices(sseu, slice), l3_en);
+ subslice = fls(l3_en);
+ drm_WARN_ON(&i915->drm, !subslice);
+ }
+ subslice--;
+
+ if (INTEL_GEN(i915) >= 11) {
+ mcr = GEN11_MCR_SLICE(slice) | GEN11_MCR_SUBSLICE(subslice);
+ mcr_mask = GEN11_MCR_SLICE_MASK | GEN11_MCR_SUBSLICE_MASK;
+ } else {
+ mcr = GEN8_MCR_SLICE(slice) | GEN8_MCR_SUBSLICE(subslice);
+ mcr_mask = GEN8_MCR_SLICE_MASK | GEN8_MCR_SUBSLICE_MASK;
+ }
+
+ drm_dbg(&i915->drm, "MCR slice/subslice = %x\n", mcr);
+
+ wa_write_clr_set(wal, GEN8_MCR_SELECTOR, mcr_mask, mcr);
+}
+
static void
gen9_gt_workarounds_init(struct drm_i915_private *i915, struct i915_wa_list *wal)
{
+ wa_init_mcr(i915, wal);
+
/* WaDisableKillLogic:bxt,skl,kbl */
if (!IS_COFFEELAKE(i915) && !IS_COMETLAKE(i915))
wa_write_or(wal,
@@ -976,78 +1050,6 @@ cfl_gt_workarounds_init(struct drm_i915_private *i915, struct i915_wa_list *wal)
GAMT_ECO_ENABLE_IN_PLACE_DECOMPRESS);
}
-static void
-wa_init_mcr(struct drm_i915_private *i915, struct i915_wa_list *wal)
-{
- const struct sseu_dev_info *sseu = &i915->gt.info.sseu;
- unsigned int slice, subslice;
- u32 l3_en, mcr, mcr_mask;
-
- GEM_BUG_ON(INTEL_GEN(i915) < 10);
-
- /*
- * WaProgramMgsrForL3BankSpecificMmioReads: cnl,icl
- * L3Banks could be fused off in single slice scenario. If that is
- * the case, we might need to program MCR select to a valid L3Bank
- * by default, to make sure we correctly read certain registers
- * later on (in the range 0xB100 - 0xB3FF).
- *
- * WaProgramMgsrForCorrectSliceSpecificMmioReads:cnl,icl
- * Before any MMIO read into slice/subslice specific registers, MCR
- * packet control register needs to be programmed to point to any
- * enabled s/ss pair. Otherwise, incorrect values will be returned.
- * This means each subsequent MMIO read will be forwarded to an
- * specific s/ss combination, but this is OK since these registers
- * are consistent across s/ss in almost all cases. In the rare
- * occasions, such as INSTDONE, where this value is dependent
- * on s/ss combo, the read should be done with read_subslice_reg.
- *
- * Since GEN8_MCR_SELECTOR contains dual-purpose bits which select both
- * to which subslice, or to which L3 bank, the respective mmio reads
- * will go, we have to find a common index which works for both
- * accesses.
- *
- * Case where we cannot find a common index fortunately should not
- * happen in production hardware, so we only emit a warning instead of
- * implementing something more complex that requires checking the range
- * of every MMIO read.
- */
-
- if (INTEL_GEN(i915) >= 10 && is_power_of_2(sseu->slice_mask)) {
- u32 l3_fuse =
- intel_uncore_read(&i915->uncore, GEN10_MIRROR_FUSE3) &
- GEN10_L3BANK_MASK;
-
- drm_dbg(&i915->drm, "L3 fuse = %x\n", l3_fuse);
- l3_en = ~(l3_fuse << GEN10_L3BANK_PAIR_COUNT | l3_fuse);
- } else {
- l3_en = ~0;
- }
-
- slice = fls(sseu->slice_mask) - 1;
- subslice = fls(l3_en & intel_sseu_get_subslices(sseu, slice));
- if (!subslice) {
- drm_warn(&i915->drm,
- "No common index found between subslice mask %x and L3 bank mask %x!\n",
- intel_sseu_get_subslices(sseu, slice), l3_en);
- subslice = fls(l3_en);
- drm_WARN_ON(&i915->drm, !subslice);
- }
- subslice--;
-
- if (INTEL_GEN(i915) >= 11) {
- mcr = GEN11_MCR_SLICE(slice) | GEN11_MCR_SUBSLICE(subslice);
- mcr_mask = GEN11_MCR_SLICE_MASK | GEN11_MCR_SUBSLICE_MASK;
- } else {
- mcr = GEN8_MCR_SLICE(slice) | GEN8_MCR_SUBSLICE(subslice);
- mcr_mask = GEN8_MCR_SLICE_MASK | GEN8_MCR_SUBSLICE_MASK;
- }
-
- drm_dbg(&i915->drm, "MCR slice/subslice = %x\n", mcr);
-
- wa_write_clr_set(wal, GEN8_MCR_SELECTOR, mcr_mask, mcr);
-}
-
static void
cnl_gt_workarounds_init(struct drm_i915_private *i915, struct i915_wa_list *wal)
{
--
2.20.1
More information about the Intel-gfx-trybot
mailing list