[Intel-gfx] [PATCH 2/4] drm/i915: Add Display Port register defines
Keith Packard
keithp at keithp.com
Fri Jun 5 17:35:27 CEST 2009
This adds the register definitions for the display port enable register
along with those for the GMCH and Link M/N ratios required to drive display
port outputs.
Signed-off-by: Keith Packard <keithp at keithp.com>
---
drivers/gpu/drm/i915/i915_reg.h | 163 +++++++++++++++++++++++++++++++++++++++
1 files changed, 163 insertions(+), 0 deletions(-)
diff --git a/drivers/gpu/drm/i915/i915_reg.h b/drivers/gpu/drm/i915/i915_reg.h
index 375569d..46d135b 100644
--- a/drivers/gpu/drm/i915/i915_reg.h
+++ b/drivers/gpu/drm/i915/i915_reg.h
@@ -631,8 +631,11 @@
/* Hotplug control (945+ only) */
#define PORT_HOTPLUG_EN 0x61110
#define HDMIB_HOTPLUG_INT_EN (1 << 29)
+#define DPB_HOTPLUG_INT_EN (1 << 29)
#define HDMIC_HOTPLUG_INT_EN (1 << 28)
+#define DPC_HOTPLUG_INT_EN (1 << 28)
#define HDMID_HOTPLUG_INT_EN (1 << 27)
+#define DPD_HOTPLUG_INT_EN (1 << 27)
#define SDVOB_HOTPLUG_INT_EN (1 << 26)
#define SDVOC_HOTPLUG_INT_EN (1 << 25)
#define TV_HOTPLUG_INT_EN (1 << 18)
@@ -665,8 +668,11 @@
#define PORT_HOTPLUG_STAT 0x61114
#define HDMIB_HOTPLUG_INT_STATUS (1 << 29)
+#define DPB_HOTPLUG_INT_STATUS (1 << 29)
#define HDMIC_HOTPLUG_INT_STATUS (1 << 28)
+#define DPC_HOTPLUG_INT_STATUS (1 << 28)
#define HDMID_HOTPLUG_INT_STATUS (1 << 27)
+#define DPD_HOTPLUG_INT_STATUS (1 << 27)
#define CRT_HOTPLUG_INT_STATUS (1 << 11)
#define TV_HOTPLUG_INT_STATUS (1 << 10)
#define CRT_HOTPLUG_MONITOR_MASK (3 << 8)
@@ -1328,6 +1334,163 @@
#define TV_V_CHROMA_0 0x68400
#define TV_V_CHROMA_42 0x684a8
+/* Display Port */
+#define DP_B 0x64100
+#define DP_C 0x64200
+#define DP_D 0x64300
+
+#define DP_PORT_EN (1 << 31)
+#define DP_PIPEB_SELECT (1 << 30)
+
+/* Link training mode - select a suitable mode for each stage */
+#define DP_LINK_TRAIN_PAT_1 (0 << 28)
+#define DP_LINK_TRAIN_PAT_2 (1 << 28)
+#define DP_LINK_TRAIN_PAT_IDLE (2 << 28)
+#define DP_LINK_TRAIN_OFF (3 << 28)
+#define DP_LINK_TRAIN_MASK (3 << 28)
+#define DP_LINK_TRAIN_SHIFT 28
+
+/* Signal voltages. These are mostly controlled by the other end */
+#define DP_VOLTAGE_0_4 (0 << 25)
+#define DP_VOLTAGE_0_6 (1 << 25)
+#define DP_VOLTAGE_0_8 (2 << 25)
+#define DP_VOLTAGE_1_2 (3 << 25)
+#define DP_VOLTAGE_MASK (7 << 25)
+#define DP_VOLTAGE_SHIFT 25
+
+/* Signal pre-emphasis levels, like voltages, the other end tells us what
+ * they want
+ */
+#define DP_PRE_EMPHASIS_0 (0 << 22)
+#define DP_PRE_EMPHASIS_3_5 (1 << 22)
+#define DP_PRE_EMPHASIS_6 (2 << 22)
+#define DP_PRE_EMPHASIS_9_5 (3 << 22)
+#define DP_PRE_EMPHASIS_MASK (7 << 22)
+#define DP_PRE_EMPHASIS_SHIFT 22
+
+/* How many wires to use. I guess 3 was too hard */
+#define DP_PORT_WIDTH_1 (0 << 19)
+#define DP_PORT_WIDTH_2 (1 << 19)
+#define DP_PORT_WIDTH_4 (3 << 19)
+#define DP_PORT_WIDTH_MASK (7 << 19)
+
+/* Mystic DPCD version 1.1 special mode */
+#define DP_ENHANCED_FRAMING (1 << 18)
+
+/** locked once port is enabled */
+#define DP_PORT_REVERSAL (1 << 15)
+
+/** sends the clock on lane 15 of the PEG for debug */
+#define DP_CLOCK_OUTPUT_ENABLE (1 << 13)
+
+#define DP_SCRAMBLING_DISABLE (1 << 12)
+
+/** limit RGB values to avoid confusing TVs */
+#define DP_COLOR_RANGE_16_235 (1 << 8)
+
+/** Turn on the audio link */
+#define DP_AUDIO_OUTPUT_ENABLE (1 << 6)
+
+/** vs and hs sync polarity */
+#define DP_SYNC_VS_HIGH (1 << 4)
+#define DP_SYNC_HS_HIGH (1 << 3)
+
+/** A fantasy */
+#define DP_DETECTED (1 << 2)
+
+/** The aux channel provides a way to talk to the
+ * signal sink for DDC etc. Max packet size supported
+ * is 20 bytes in each direction, hence the 5 fixed
+ * data registers
+ */
+#define DPB_AUX_CH_CTL 0x64110
+#define DPB_AUX_CH_DATA1 0x64114
+#define DPB_AUX_CH_DATA2 0x64118
+#define DPB_AUX_CH_DATA3 0x6411c
+#define DPB_AUX_CH_DATA4 0x64120
+#define DPB_AUX_CH_DATA5 0x64124
+
+#define DPC_AUX_CH_CTL 0x64210
+#define DPC_AUX_CH_DATA1 0x64214
+#define DPC_AUX_CH_DATA2 0x64218
+#define DPC_AUX_CH_DATA3 0x6421c
+#define DPC_AUX_CH_DATA4 0x64220
+#define DPC_AUX_CH_DATA5 0x64224
+
+#define DPD_AUX_CH_CTL 0x64310
+#define DPD_AUX_CH_DATA1 0x64314
+#define DPD_AUX_CH_DATA2 0x64318
+#define DPD_AUX_CH_DATA3 0x6431c
+#define DPD_AUX_CH_DATA4 0x64320
+#define DPD_AUX_CH_DATA5 0x64324
+
+#define DP_AUX_CH_CTL_SEND_BUSY (1 << 31)
+#define DP_AUX_CH_CTL_DONE (1 << 30)
+#define DP_AUX_CH_CTL_INTERRUPT (1 << 29)
+#define DP_AUX_CH_CTL_TIME_OUT_ERROR (1 << 28)
+#define DP_AUX_CH_CTL_TIME_OUT_400us (0 << 26)
+#define DP_AUX_CH_CTL_TIME_OUT_600us (1 << 26)
+#define DP_AUX_CH_CTL_TIME_OUT_800us (2 << 26)
+#define DP_AUX_CH_CTL_TIME_OUT_1600us (3 << 26)
+#define DP_AUX_CH_CTL_TIME_OUT_MASK (3 << 26)
+#define DP_AUX_CH_CTL_RECEIVE_ERROR (1 << 25)
+#define DP_AUX_CH_CTL_MESSAGE_SIZE_MASK (0x1f << 20)
+#define DP_AUX_CH_CTL_MESSAGE_SIZE_SHIFT 20
+#define DP_AUX_CH_CTL_PRECHARGE_2US_MASK (0xf << 16)
+#define DP_AUX_CH_CTL_PRECHARGE_2US_SHIFT 16
+#define DP_AUX_CH_CTL_AUX_AKSV_SELECT (1 << 15)
+#define DP_AUX_CH_CTL_MANCHESTER_TEST (1 << 14)
+#define DP_AUX_CH_CTL_SYNC_TEST (1 << 13)
+#define DP_AUX_CH_CTL_DEGLITCH_TEST (1 << 12)
+#define DP_AUX_CH_CTL_PRECHARGE_TEST (1 << 11)
+#define DP_AUX_CH_CTL_BIT_CLOCK_2X_MASK (0x7ff)
+#define DP_AUX_CH_CTL_BIT_CLOCK_2X_SHIFT 0
+
+/*
+ * Computing GMCH M and N values for the Display Port link
+ *
+ * GMCH M/N = dot clock * bytes per pixel / ls_clk * # of lanes
+ *
+ * ls_clk (we assume) is the DP link clock (1.62 or 2.7 GHz)
+ *
+ * The GMCH value is used internally
+ *
+ * bytes_per_pixel is the number of bytes coming out of the plane,
+ * which is after the LUTs, so we want the bytes for our color format.
+ * For our current usage, this is always 3, one byte for R, G and B.
+ */
+#define PIPEA_GMCH_DATA_M 0x70050
+#define PIPEB_GMCH_DATA_M 0x71050
+
+/* Transfer unit size for display port - 1, default is 0x3f (for TU size 64) */
+#define PIPE_GMCH_DATA_M_TU_SIZE_MASK (0x3f << 25)
+#define PIPE_GMCH_DATA_M_TU_SIZE_SHIFT 25
+
+#define PIPE_GMCH_DATA_M_MASK (0xffffff)
+
+#define PIPEA_GMCH_DATA_N 0x70054
+#define PIPEB_GMCH_DATA_N 0x71054
+#define PIPE_GMCH_DATA_N_MASK (0xffffff)
+
+/*
+ * Computing Link M and N values for the Display Port link
+ *
+ * Link M / N = pixel_clock / ls_clk
+ *
+ * (the DP spec calls pixel_clock the 'strm_clk')
+ *
+ * The Link value is transmitted in the Main Stream
+ * Attributes and VB-ID.
+ */
+
+#define PIPEA_DP_LINK_M 0x70060
+#define PIPEB_DP_LINK_M 0x71060
+#define PIPEA_DP_LINK_M_MASK (0xffffff)
+
+#define PIPEA_DP_LINK_N 0x70064
+#define PIPEB_DP_LINK_N 0x71064
+#define PIPEA_DP_LINK_N_MASK (0xffffff)
+
/* Display & cursor control */
/* Pipe A */
--
1.6.3.1
More information about the Intel-gfx
mailing list