[Intel-gfx] Intel KMS and custom modelines?
David Härdeman
david at hardeman.nu
Sat Sep 5 20:08:30 CEST 2009
On Fri, Sep 04, 2009 at 03:20:35PM +0800, ykzhao wrote:
>On Fri, 2009-09-04 at 14:24 +0800, David Härdeman wrote:
>> I recently bought a HDMI capable receiver and now I have my Intel G45
>> based HTPC connected through the receiver to my LCD tv using HDMI
>> instead of a direct connection to the TV. This has brought loads of fun.
>>
>> During X.org startup I experience the following problems:
>
>Can you confirm whether it can work well under UMS mode?
The x.org server works well under KMS or UMS provided I use the
xorg.conf that I attached to my previous mail. The question is not
regarding KMS or UMS but rather if it is possible to use custom
modelines and forced outputs using the KMS driver while using the
console, during boot etc?
>Will you please attach the xorg.log under the following two cases?
>Please test it in UMS mode.
I've attached three xorg.log files, the file names should tell you which
xorg.log belongs to which scenario. All log files are made with no
xorg.conf at all (and only the tv-on, receiver-on scenario ends up with
a usable mode). But as I said, I don't think the log files are relevant
to my scenario (getting a specific mode on a specific output even before
x.org starts).
Regards,
David
-------------- next part --------------
X.Org X Server 1.6.3
Release Date: 2009-7-31
X Protocol Version 11, Revision 0
Build Operating System: Linux 2.6.30-1-amd64 x86_64 Debian
Current Operating System: Linux scott 2.6.30-1-amd64 #1 SMP Fri Aug 7 23:20:43 CEST 2009 x86_64
Build Date: 31 August 2009 11:11:11PM
xorg-server 2:1.6.3-1 (david at hardeman.nu)
Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.log", Time: Sat Sep 5 19:55:43 2009
(II) Loader magic: 0x34c0
(II) Module ABI versions:
X.Org ANSI C Emulation: 0.4
X.Org Video Driver: 5.0
X.Org XInput driver : 4.0
X.Org Server Extension : 2.0
(II) Loader running on linux
(++) using VT number 7
(--) PCI:*(0:0:2:0) 8086:2e22:8086:5003 Intel Corporation 4 Series Chipset Integrated Graphics Controller rev 3, Mem @ 0xff400000/4194304, 0xd0000000/268435456, I/O @ 0x0000f1c0/8
(==) Using default built-in configuration (39 lines)
(==) --- Start of built-in configuration ---
Section "Device"
Identifier "Builtin Default intel Device 0"
Driver "intel"
EndSection
Section "Screen"
Identifier "Builtin Default intel Screen 0"
Device "Builtin Default intel Device 0"
EndSection
Section "Device"
Identifier "Builtin Default i810 Device 0"
Driver "i810"
EndSection
Section "Screen"
Identifier "Builtin Default i810 Screen 0"
Device "Builtin Default i810 Device 0"
EndSection
Section "Device"
Identifier "Builtin Default vesa Device 0"
Driver "vesa"
EndSection
Section "Screen"
Identifier "Builtin Default vesa Screen 0"
Device "Builtin Default vesa Device 0"
EndSection
Section "Device"
Identifier "Builtin Default fbdev Device 0"
Driver "fbdev"
EndSection
Section "Screen"
Identifier "Builtin Default fbdev Screen 0"
Device "Builtin Default fbdev Device 0"
EndSection
Section "ServerLayout"
Identifier "Builtin Default Layout"
Screen "Builtin Default intel Screen 0"
Screen "Builtin Default i810 Screen 0"
Screen "Builtin Default vesa Screen 0"
Screen "Builtin Default fbdev Screen 0"
EndSection
(==) --- End of built-in configuration ---
(==) ServerLayout "Builtin Default Layout"
(**) |-->Screen "Builtin Default intel Screen 0" (0)
(**) | |-->Monitor "<default monitor>"
(**) | |-->Device "Builtin Default intel Device 0"
(==) No monitor specified for screen "Builtin Default intel Screen 0".
Using a default monitor configuration.
(**) |-->Screen "Builtin Default i810 Screen 0" (1)
(**) | |-->Monitor "<default monitor>"
(**) | |-->Device "Builtin Default i810 Device 0"
(==) No monitor specified for screen "Builtin Default i810 Screen 0".
Using a default monitor configuration.
(**) |-->Screen "Builtin Default vesa Screen 0" (2)
(**) | |-->Monitor "<default monitor>"
(**) | |-->Device "Builtin Default vesa Device 0"
(==) No monitor specified for screen "Builtin Default vesa Screen 0".
Using a default monitor configuration.
(**) |-->Screen "Builtin Default fbdev Screen 0" (3)
(**) | |-->Monitor "<default monitor>"
(**) | |-->Device "Builtin Default fbdev Device 0"
(==) No monitor specified for screen "Builtin Default fbdev Screen 0".
Using a default monitor configuration.
(==) Automatically adding devices
(==) Automatically enabling devices
(WW) The directory "/usr/share/fonts/X11/cyrillic" does not exist.
Entry deleted from font path.
(WW) The directory "/usr/share/fonts/X11/75dpi/" does not exist.
Entry deleted from font path.
(WW) The directory "/usr/share/fonts/X11/Type1" does not exist.
Entry deleted from font path.
(WW) The directory "/usr/share/fonts/X11/75dpi" does not exist.
Entry deleted from font path.
(WW) The directory "/var/lib/defoma/x-ttcidfont-conf.d/dirs/TrueType" does not exist.
Entry deleted from font path.
(==) FontPath set to:
/usr/share/fonts/X11/misc,
/usr/share/fonts/X11/100dpi/:unscaled,
/usr/share/fonts/X11/100dpi,
built-ins
(==) ModulePath set to "/usr/lib/xorg/modules"
(II) Cannot locate a core pointer device.
(II) Cannot locate a core keyboard device.
(II) The server relies on HAL to provide the list of input devices.
If no devices become available, reconfigure HAL or disable AllowEmptyInput.
(II) Open ACPI successful (/var/run/acpid.socket)
(II) System resource ranges:
[0] -1 0 0xffffffff - 0xffffffff (0x1) MX[B]
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[4] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[5] -1 0 0x00000000 - 0x00000000 (0x1) IX[B]
(II) LoadModule: "extmod"
(II) Loading /usr/lib/xorg/modules/extensions//libextmod.so
(II) Module extmod: vendor="X.Org Foundation"
compiled for 1.6.3, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension SELinux
(II) Loading extension MIT-SCREEN-SAVER
(II) Loading extension XFree86-VidModeExtension
(II) Loading extension XFree86-DGA
(II) Loading extension DPMS
(II) Loading extension XVideo
(II) Loading extension XVideo-MotionCompensation
(II) Loading extension X-Resource
(II) LoadModule: "dbe"
(II) Loading /usr/lib/xorg/modules/extensions//libdbe.so
(II) Module dbe: vendor="X.Org Foundation"
compiled for 1.6.3, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension DOUBLE-BUFFER
(II) LoadModule: "glx"
(II) Loading /usr/lib/xorg/modules/extensions//libglx.so
(II) Module glx: vendor="X.Org Foundation"
compiled for 1.6.3, module version = 1.0.0
ABI class: X.Org Server Extension, version 2.0
(==) AIGLX enabled
(II) Loading extension GLX
(II) LoadModule: "record"
(II) Loading /usr/lib/xorg/modules/extensions//librecord.so
(II) Module record: vendor="X.Org Foundation"
compiled for 1.6.3, module version = 1.13.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension RECORD
(II) LoadModule: "dri"
(II) Loading /usr/lib/xorg/modules/extensions//libdri.so
(II) Module dri: vendor="X.Org Foundation"
compiled for 1.6.3, module version = 1.0.0
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension XFree86-DRI
(II) LoadModule: "dri2"
(II) Loading /usr/lib/xorg/modules/extensions//libdri2.so
(II) Module dri2: vendor="X.Org Foundation"
compiled for 1.6.3, module version = 1.1.0
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension DRI2
(II) LoadModule: "intel"
(II) Loading /usr/lib/xorg/modules/drivers//intel_drv.so
(II) Module intel: vendor="X.Org Foundation"
compiled for 1.6.3, module version = 2.8.1
Module class: X.Org Video Driver
ABI class: X.Org Video Driver, version 5.0
(II) LoadModule: "i810"
(WW) Warning, couldn't open module i810
(II) UnloadModule: "i810"
(EE) Failed to load module "i810" (module does not exist, 0)
(II) LoadModule: "vesa"
(WW) Warning, couldn't open module vesa
(II) UnloadModule: "vesa"
(EE) Failed to load module "vesa" (module does not exist, 0)
(II) LoadModule: "fbdev"
(WW) Warning, couldn't open module fbdev
(II) UnloadModule: "fbdev"
(EE) Failed to load module "fbdev" (module does not exist, 0)
(II) intel: Driver for Intel Integrated Graphics Chipsets: i810,
i810-dc100, i810e, i815, i830M, 845G, 852GM/855GM, 865G, 915G,
E7221 (i915), 915GM, 945G, 945GM, 945GME, IGD_GM, IGD_G, 965G, G35,
965Q, 946GZ, 965GM, 965GME/GLE, G33, Q35, Q33,
Mobile Intel® GM45 Express Chipset,
Intel Integrated Graphics Device, G45/G43, Q45/Q43, G41, IGDNG_D,
IGDNG_M
(II) Primary Device is: PCI 00 at 00:02:0
(II) resource ranges after xf86ClaimFixedResources() call:
[0] -1 0 0xffffffff - 0xffffffff (0x1) MX[B]
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[4] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[5] -1 0 0x00000000 - 0x00000000 (0x1) IX[B]
(II) resource ranges after probing:
[0] -1 0 0xffffffff - 0xffffffff (0x1) MX[B]
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[4] 0 0 0x000a0000 - 0x000affff (0x10000) MS[B]
[5] 0 0 0x000b0000 - 0x000b7fff (0x8000) MS[B]
[6] 0 0 0x000b8000 - 0x000bffff (0x8000) MS[B]
[7] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[8] -1 0 0x00000000 - 0x00000000 (0x1) IX[B]
[9] 0 0 0x000003b0 - 0x000003bb (0xc) IS[B]
[10] 0 0 0x000003c0 - 0x000003df (0x20) IS[B]
(II) Loading sub module "vgahw"
(II) LoadModule: "vgahw"
(II) Loading /usr/lib/xorg/modules//libvgahw.so
(II) Module vgahw: vendor="X.Org Foundation"
compiled for 1.6.3, module version = 0.1.0
ABI class: X.Org Video Driver, version 5.0
(II) Loading sub module "ramdac"
(II) LoadModule: "ramdac"
(II) Module "ramdac" already built-in
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 9, (OK)
drmOpenByBusid: Searching for BusID pci:0000:00:02.0
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 9, (OK)
drmOpenByBusid: drmOpenMinor returns 9
drmOpenByBusid: drmGetBusid reports pci:0000:00:02.0
(II) intel(0): Creating default Display subsection in Screen section
"Builtin Default intel Screen 0" for depth/fbbpp 24/32
(==) intel(0): Depth 24, (--) framebuffer bpp 32
(==) intel(0): RGB weight 888
(==) intel(0): Default visual is TrueColor
(II) intel(0): Integrated Graphics Chipset: Intel(R) G45/G43
(--) intel(0): Chipset: "G45/G43"
(--) intel(0): Linear framebuffer at 0xD0000000
(--) intel(0): IO registers at addr 0xFF400000 size 4194304
(WW) intel(0): libpciaccess reported 0 rom size, guessing 64kB
(II) intel(0): No SDVO device is found in VBT
(II) intel(0): 2 display pipes available.
(II) Loading sub module "ddc"
(II) LoadModule: "ddc"
(II) Module "ddc" already built-in
(II) Loading sub module "i2c"
(II) LoadModule: "i2c"
(II) Module "i2c" already built-in
(II) intel(0): Output VGA has no monitor section
(II) intel(0): I2C bus "SDVOCTRL_E for SDVOB" initialized.
(II) intel(0): I2C device "SDVOCTRL_E for SDVOB:SDVO Controller B" registered at address 0x70.
(II) intel(0): No SDVO device found on SDVOB
(II) intel(0): I2C device "SDVOCTRL_E for SDVOB:SDVO Controller B" removed.
(II) intel(0): I2C bus "SDVOCTRL_E for SDVOB" removed.
(II) intel(0): Output HDMI-1 has no monitor section
(II) intel(0): I2C bus "HDMIDDC_B" initialized.
(II) intel(0): HDMI output 1 detected
(II) intel(0): I2C bus "SDVOCTRL_E for SDVOC" initialized.
(II) intel(0): I2C device "SDVOCTRL_E for SDVOC:SDVO Controller C" registered at address 0x72.
(II) intel(0): No SDVO device found on SDVOC
(II) intel(0): I2C device "SDVOCTRL_E for SDVOC:SDVO Controller C" removed.
(II) intel(0): I2C bus "SDVOCTRL_E for SDVOC" removed.
(II) intel(0): Output HDMI-2 has no monitor section
(II) intel(0): I2C bus "HDMIDDC_C" initialized.
(II) intel(0): HDMI output 2 detected
(II) intel(0): EDID for output VGA
(II) intel(0): EDID for output HDMI-1
(II) intel(0): EDID for output HDMI-2
(II) intel(0): Output VGA disconnected
(II) intel(0): Output HDMI-1 disconnected
(II) intel(0): Output HDMI-2 disconnected
(WW) intel(0): No outputs definitely connected, trying again...
(II) intel(0): Output VGA disconnected
(II) intel(0): Output HDMI-1 disconnected
(II) intel(0): Output HDMI-2 disconnected
(WW) intel(0): Unable to find initial modes
(EE) intel(0): No valid modes.
(II) UnloadModule: "intel"
(II) UnloadModule: "vgahw"
(II) Unloading /usr/lib/xorg/modules//libvgahw.so
(EE) Screen(s) found, but none have a usable configuration.
Fatal server error:
no screens found
Please consult the The X.Org Foundation support
at http://wiki.x.org
for help.
Please also check the log file at "/var/log/Xorg.0.log" for additional information.
-------------- next part --------------
X.Org X Server 1.6.3
Release Date: 2009-7-31
X Protocol Version 11, Revision 0
Build Operating System: Linux 2.6.30-1-amd64 x86_64 Debian
Current Operating System: Linux scott 2.6.30-1-amd64 #1 SMP Fri Aug 7 23:20:43 CEST 2009 x86_64
Build Date: 31 August 2009 11:11:11PM
xorg-server 2:1.6.3-1 (david at hardeman.nu)
Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.log", Time: Sat Sep 5 19:53:34 2009
(II) Loader magic: 0x34c0
(II) Module ABI versions:
X.Org ANSI C Emulation: 0.4
X.Org Video Driver: 5.0
X.Org XInput driver : 4.0
X.Org Server Extension : 2.0
(II) Loader running on linux
(++) using VT number 7
(--) PCI:*(0:0:2:0) 8086:2e22:8086:5003 Intel Corporation 4 Series Chipset Integrated Graphics Controller rev 3, Mem @ 0xff400000/4194304, 0xd0000000/268435456, I/O @ 0x0000f1c0/8
(==) Using default built-in configuration (39 lines)
(==) --- Start of built-in configuration ---
Section "Device"
Identifier "Builtin Default intel Device 0"
Driver "intel"
EndSection
Section "Screen"
Identifier "Builtin Default intel Screen 0"
Device "Builtin Default intel Device 0"
EndSection
Section "Device"
Identifier "Builtin Default i810 Device 0"
Driver "i810"
EndSection
Section "Screen"
Identifier "Builtin Default i810 Screen 0"
Device "Builtin Default i810 Device 0"
EndSection
Section "Device"
Identifier "Builtin Default vesa Device 0"
Driver "vesa"
EndSection
Section "Screen"
Identifier "Builtin Default vesa Screen 0"
Device "Builtin Default vesa Device 0"
EndSection
Section "Device"
Identifier "Builtin Default fbdev Device 0"
Driver "fbdev"
EndSection
Section "Screen"
Identifier "Builtin Default fbdev Screen 0"
Device "Builtin Default fbdev Device 0"
EndSection
Section "ServerLayout"
Identifier "Builtin Default Layout"
Screen "Builtin Default intel Screen 0"
Screen "Builtin Default i810 Screen 0"
Screen "Builtin Default vesa Screen 0"
Screen "Builtin Default fbdev Screen 0"
EndSection
(==) --- End of built-in configuration ---
(==) ServerLayout "Builtin Default Layout"
(**) |-->Screen "Builtin Default intel Screen 0" (0)
(**) | |-->Monitor "<default monitor>"
(**) | |-->Device "Builtin Default intel Device 0"
(==) No monitor specified for screen "Builtin Default intel Screen 0".
Using a default monitor configuration.
(**) |-->Screen "Builtin Default i810 Screen 0" (1)
(**) | |-->Monitor "<default monitor>"
(**) | |-->Device "Builtin Default i810 Device 0"
(==) No monitor specified for screen "Builtin Default i810 Screen 0".
Using a default monitor configuration.
(**) |-->Screen "Builtin Default vesa Screen 0" (2)
(**) | |-->Monitor "<default monitor>"
(**) | |-->Device "Builtin Default vesa Device 0"
(==) No monitor specified for screen "Builtin Default vesa Screen 0".
Using a default monitor configuration.
(**) |-->Screen "Builtin Default fbdev Screen 0" (3)
(**) | |-->Monitor "<default monitor>"
(**) | |-->Device "Builtin Default fbdev Device 0"
(==) No monitor specified for screen "Builtin Default fbdev Screen 0".
Using a default monitor configuration.
(==) Automatically adding devices
(==) Automatically enabling devices
(WW) The directory "/usr/share/fonts/X11/cyrillic" does not exist.
Entry deleted from font path.
(WW) The directory "/usr/share/fonts/X11/75dpi/" does not exist.
Entry deleted from font path.
(WW) The directory "/usr/share/fonts/X11/Type1" does not exist.
Entry deleted from font path.
(WW) The directory "/usr/share/fonts/X11/75dpi" does not exist.
Entry deleted from font path.
(WW) The directory "/var/lib/defoma/x-ttcidfont-conf.d/dirs/TrueType" does not exist.
Entry deleted from font path.
(==) FontPath set to:
/usr/share/fonts/X11/misc,
/usr/share/fonts/X11/100dpi/:unscaled,
/usr/share/fonts/X11/100dpi,
built-ins
(==) ModulePath set to "/usr/lib/xorg/modules"
(II) Cannot locate a core pointer device.
(II) Cannot locate a core keyboard device.
(II) The server relies on HAL to provide the list of input devices.
If no devices become available, reconfigure HAL or disable AllowEmptyInput.
(II) Open ACPI successful (/var/run/acpid.socket)
(II) System resource ranges:
[0] -1 0 0xffffffff - 0xffffffff (0x1) MX[B]
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[4] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[5] -1 0 0x00000000 - 0x00000000 (0x1) IX[B]
(II) LoadModule: "extmod"
(II) Loading /usr/lib/xorg/modules/extensions//libextmod.so
(II) Module extmod: vendor="X.Org Foundation"
compiled for 1.6.3, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension SELinux
(II) Loading extension MIT-SCREEN-SAVER
(II) Loading extension XFree86-VidModeExtension
(II) Loading extension XFree86-DGA
(II) Loading extension DPMS
(II) Loading extension XVideo
(II) Loading extension XVideo-MotionCompensation
(II) Loading extension X-Resource
(II) LoadModule: "dbe"
(II) Loading /usr/lib/xorg/modules/extensions//libdbe.so
(II) Module dbe: vendor="X.Org Foundation"
compiled for 1.6.3, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension DOUBLE-BUFFER
(II) LoadModule: "glx"
(II) Loading /usr/lib/xorg/modules/extensions//libglx.so
(II) Module glx: vendor="X.Org Foundation"
compiled for 1.6.3, module version = 1.0.0
ABI class: X.Org Server Extension, version 2.0
(==) AIGLX enabled
(II) Loading extension GLX
(II) LoadModule: "record"
(II) Loading /usr/lib/xorg/modules/extensions//librecord.so
(II) Module record: vendor="X.Org Foundation"
compiled for 1.6.3, module version = 1.13.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension RECORD
(II) LoadModule: "dri"
(II) Loading /usr/lib/xorg/modules/extensions//libdri.so
(II) Module dri: vendor="X.Org Foundation"
compiled for 1.6.3, module version = 1.0.0
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension XFree86-DRI
(II) LoadModule: "dri2"
(II) Loading /usr/lib/xorg/modules/extensions//libdri2.so
(II) Module dri2: vendor="X.Org Foundation"
compiled for 1.6.3, module version = 1.1.0
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension DRI2
(II) LoadModule: "intel"
(II) Loading /usr/lib/xorg/modules/drivers//intel_drv.so
(II) Module intel: vendor="X.Org Foundation"
compiled for 1.6.3, module version = 2.8.1
Module class: X.Org Video Driver
ABI class: X.Org Video Driver, version 5.0
(II) LoadModule: "i810"
(WW) Warning, couldn't open module i810
(II) UnloadModule: "i810"
(EE) Failed to load module "i810" (module does not exist, 0)
(II) LoadModule: "vesa"
(WW) Warning, couldn't open module vesa
(II) UnloadModule: "vesa"
(EE) Failed to load module "vesa" (module does not exist, 0)
(II) LoadModule: "fbdev"
(WW) Warning, couldn't open module fbdev
(II) UnloadModule: "fbdev"
(EE) Failed to load module "fbdev" (module does not exist, 0)
(II) intel: Driver for Intel Integrated Graphics Chipsets: i810,
i810-dc100, i810e, i815, i830M, 845G, 852GM/855GM, 865G, 915G,
E7221 (i915), 915GM, 945G, 945GM, 945GME, IGD_GM, IGD_G, 965G, G35,
965Q, 946GZ, 965GM, 965GME/GLE, G33, Q35, Q33,
Mobile Intel® GM45 Express Chipset,
Intel Integrated Graphics Device, G45/G43, Q45/Q43, G41, IGDNG_D,
IGDNG_M
(II) Primary Device is: PCI 00 at 00:02:0
(II) resource ranges after xf86ClaimFixedResources() call:
[0] -1 0 0xffffffff - 0xffffffff (0x1) MX[B]
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[4] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[5] -1 0 0x00000000 - 0x00000000 (0x1) IX[B]
(II) resource ranges after probing:
[0] -1 0 0xffffffff - 0xffffffff (0x1) MX[B]
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[4] 0 0 0x000a0000 - 0x000affff (0x10000) MS[B]
[5] 0 0 0x000b0000 - 0x000b7fff (0x8000) MS[B]
[6] 0 0 0x000b8000 - 0x000bffff (0x8000) MS[B]
[7] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[8] -1 0 0x00000000 - 0x00000000 (0x1) IX[B]
[9] 0 0 0x000003b0 - 0x000003bb (0xc) IS[B]
[10] 0 0 0x000003c0 - 0x000003df (0x20) IS[B]
(II) Loading sub module "vgahw"
(II) LoadModule: "vgahw"
(II) Loading /usr/lib/xorg/modules//libvgahw.so
(II) Module vgahw: vendor="X.Org Foundation"
compiled for 1.6.3, module version = 0.1.0
ABI class: X.Org Video Driver, version 5.0
(II) Loading sub module "ramdac"
(II) LoadModule: "ramdac"
(II) Module "ramdac" already built-in
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 9, (OK)
drmOpenByBusid: Searching for BusID pci:0000:00:02.0
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 9, (OK)
drmOpenByBusid: drmOpenMinor returns 9
drmOpenByBusid: drmGetBusid reports pci:0000:00:02.0
(II) intel(0): Creating default Display subsection in Screen section
"Builtin Default intel Screen 0" for depth/fbbpp 24/32
(==) intel(0): Depth 24, (--) framebuffer bpp 32
(==) intel(0): RGB weight 888
(==) intel(0): Default visual is TrueColor
(II) intel(0): Integrated Graphics Chipset: Intel(R) G45/G43
(--) intel(0): Chipset: "G45/G43"
(--) intel(0): Linear framebuffer at 0xD0000000
(--) intel(0): IO registers at addr 0xFF400000 size 4194304
(WW) intel(0): libpciaccess reported 0 rom size, guessing 64kB
(II) intel(0): No SDVO device is found in VBT
(II) intel(0): 2 display pipes available.
(II) Loading sub module "ddc"
(II) LoadModule: "ddc"
(II) Module "ddc" already built-in
(II) Loading sub module "i2c"
(II) LoadModule: "i2c"
(II) Module "i2c" already built-in
(II) intel(0): Output VGA has no monitor section
(II) intel(0): I2C bus "SDVOCTRL_E for SDVOB" initialized.
(II) intel(0): I2C device "SDVOCTRL_E for SDVOB:SDVO Controller B" registered at address 0x70.
(II) intel(0): No SDVO device found on SDVOB
(II) intel(0): I2C device "SDVOCTRL_E for SDVOB:SDVO Controller B" removed.
(II) intel(0): I2C bus "SDVOCTRL_E for SDVOB" removed.
(II) intel(0): Output HDMI-1 has no monitor section
(II) intel(0): I2C bus "HDMIDDC_B" initialized.
(II) intel(0): HDMI output 1 detected
(II) intel(0): I2C bus "SDVOCTRL_E for SDVOC" initialized.
(II) intel(0): I2C device "SDVOCTRL_E for SDVOC:SDVO Controller C" registered at address 0x72.
(II) intel(0): No SDVO device found on SDVOC
(II) intel(0): I2C device "SDVOCTRL_E for SDVOC:SDVO Controller C" removed.
(II) intel(0): I2C bus "SDVOCTRL_E for SDVOC" removed.
(II) intel(0): Output HDMI-2 has no monitor section
(II) intel(0): I2C bus "HDMIDDC_C" initialized.
(II) intel(0): HDMI output 2 detected
(II) intel(0): EDID for output VGA
(II) intel(0): I2C device "HDMIDDC_B:E-EDID segment register" registered at address 0x60.
(II) intel(0): I2C device "HDMIDDC_B:ddc2" registered at address 0xA0.
(II) intel(0): EDID for output HDMI-1
(II) intel(0): Manufacturer: MJI Model: 11 Serial#: 0
(II) intel(0): Year: 2007 Week: 0
(II) intel(0): EDID Version: 1.3
(II) intel(0): Digital Display Input
(II) intel(0): Indeterminate output size
(II) intel(0): Gamma: 2.20
(II) intel(0): No DPMS capabilities specified
(II) intel(0): Supported color encodings: RGB 4:4:4 YCrCb 4:4:4
(II) intel(0): First detailed timing is preferred mode
(II) intel(0): redX: 0.640 redY: 0.330 greenX: 0.300 greenY: 0.600
(II) intel(0): blueX: 0.150 blueY: 0.060 whiteX: 0.312 whiteY: 0.329
(II) intel(0): Supported established timings:
(II) intel(0): 640x480 at 60Hz
(II) intel(0): Manufacturer's mask: 0
(II) intel(0): Supported detailed timing:
(II) intel(0): clock: 74.2 MHz Image Size: 708 x 398 mm
(II) intel(0): h_active: 1920 h_sync: 2008 h_sync_end 2052 h_blank_end 2200 h_border: 0
(II) intel(0): v_active: 540 v_sync: 542 v_sync_end 547 v_blanking: 562 v_border: 0
(II) intel(0): Supported detailed timing:
(II) intel(0): clock: 74.2 MHz Image Size: 708 x 398 mm
(II) intel(0): h_active: 1920 h_sync: 2448 h_sync_end 2492 h_blank_end 2640 h_border: 0
(II) intel(0): v_active: 540 v_sync: 542 v_sync_end 547 v_blanking: 562 v_border: 0
(II) intel(0): Ranges: V min: 49 V max: 61 Hz, H min: 15 H max: 46 kHz, PixClock max 80 MHz
(II) intel(0): Monitor name: SR8002 HDMI2
(II) intel(0): Number of EDID sections to follow: 1
(II) intel(0): EDID (in hex):
(II) intel(0): 00ffffffffffff003549110000000000
(II) intel(0): 00110103800000780aee91a3544c9926
(II) intel(0): 0f505420000001010101010101010101
(II) intel(0): 010101010101011d8018711c1620582c
(II) intel(0): 2500c48e2100009e011d80d0721c1620
(II) intel(0): 102c2580c48e2100009e000000fd0031
(II) intel(0): 3d0f2e08000a202020202020000000fc
(II) intel(0): 005352383030322048444d49320a0141
(II) intel(0): 020348725f8594041302110312010615
(II) intel(0): 07160e0f1d1e101f0a0b191a0c0d1b1c
(II) intel(0): 2324252638097f070f7f071507503d07
(II) intel(0): c04d02005706005f7e01677e00834f00
(II) intel(0): 0066030c00200080011d007251d01e20
(II) intel(0): 6e285500c48e2100001e011d00bc52d0
(II) intel(0): 1e20b8285540c48e2100001e8c0ad08a
(II) intel(0): 20e02d10103e9600c48e210000180037
(II) intel(0): EDID vendor "MJI", prod id 17
(II) intel(0): Printing probed modes for output HDMI-1
(II) intel(0): Modeline "1920x540"x120.1 74.25 1920 2008 2052 2200 540 542 547 562 interlace +hsync +vsync (33.8 kHz)
(II) intel(0): Modeline "1920x540"x100.1 74.25 1920 2448 2492 2640 540 542 547 562 interlace +hsync +vsync (28.1 kHz)
(II) intel(0): Modeline "640x480"x59.9 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz)
(II) intel(0): EDID for output HDMI-2
(II) intel(0): Output VGA disconnected
(II) intel(0): Output HDMI-1 connected
(II) intel(0): Output HDMI-2 disconnected
(II) intel(0): Using exact sizes for initial modes
(II) intel(0): Output HDMI-1 using initial mode 1920x540
(II) intel(0): detected 512 kB GTT.
(II) intel(0): detected 32764 kB stolen memory.
(==) intel(0): video overlay key set to 0x101fe
(==) intel(0): Using gamma correction (1.0, 1.0, 1.0)
(==) intel(0): DPI set to (96, 96)
(II) Loading sub module "fb"
(II) LoadModule: "fb"
(II) Loading /usr/lib/xorg/modules//libfb.so
(II) Module fb: vendor="X.Org Foundation"
compiled for 1.6.3, module version = 1.0.0
ABI class: X.Org ANSI C Emulation, version 0.4
(II) intel(0): Comparing regs from server start up to After PreInit
(WW) intel(0): Register 0x61110 (PORT_HOTPLUG_EN) changed from 0x00000000 to 0x30000120
(WW) intel(0): Register 0x61114 (PORT_HOTPLUG_STAT) changed from 0x00000000 to 0x20100000
(WW) intel(0): Register 0x70024 (PIPEASTAT) changed from 0x00000206 to 0x80000206
(WW) intel(0): PIPEASTAT before: status: VSYNC_INT_STATUS SVBLANK_INT_STATUS VBLANK_INT_STATUS
(WW) intel(0): PIPEASTAT after: status: FIFO_UNDERRUN VSYNC_INT_STATUS SVBLANK_INT_STATUS VBLANK_INT_STATUS
(==) Depth 24 pixmap format is 32 bpp
(II) do I need RAC? No, I don't.
(II) resource ranges after preInit:
[0] -1 0 0xffffffff - 0xffffffff (0x1) MX[B]
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[4] 0 0 0x000a0000 - 0x000affff (0x10000) MS[B](OprD)
[5] 0 0 0x000b0000 - 0x000b7fff (0x8000) MS[B](OprD)
[6] 0 0 0x000b8000 - 0x000bffff (0x8000) MS[B](OprD)
[7] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[8] -1 0 0x00000000 - 0x00000000 (0x1) IX[B]
[9] 0 0 0x000003b0 - 0x000003bb (0xc) IS[B](OprU)
[10] 0 0 0x000003c0 - 0x000003df (0x20) IS[B](OprU)
(II) intel(0): Kernel reported 1248000 total, 1 used
(II) intel(0): I830CheckAvailableMemory: 4991996 kB available
(II) intel(0): [DRI2] Setup complete
(**) intel(0): Framebuffer compression disabled
(**) intel(0): Tiling enabled
(**) intel(0): SwapBuffers wait enabled
(==) intel(0): VideoRam: 262144 KB
(II) intel(0): Attempting memory allocation with tiled buffers.
(II) intel(0): Tiled allocation successful.
(II) intel(0): vgaHWGetIOBase: hwp->IOBase is 0x03d0, hwp->PIOOffset is 0x0000
(II) UXA(0): Driver registered support for the following operations:
(II) solid
(II) copy
(II) composite (RENDER acceleration)
(==) intel(0): Backing store disabled
(==) intel(0): Silken mouse enabled
(II) intel(0): Initializing HW Cursor
(II) intel(0): Fixed memory allocation layout:
(II) intel(0): 0x01fff000: end of stolen memory
(II) intel(0): 0x01fff000-0x0fffffff: DRI memory manager (229380 kB)
(II) intel(0): 0x10000000: end of aperture
(II) intel(0): BO memory allocation layout:
(II) intel(0): 0x01fff000: start of memory manager
(II) intel(0): 0x02020000-0x02414fff: front buffer (4052 kB) X tiled
(II) intel(0): 0x02420000-0x02429fff: HW cursors (40 kB)
(II) intel(0): 0x10000000: end of memory manager
(WW) intel(0): ESR is 0x00000011, page table error
(WW) intel(0): PGTBL_ER is 0x00100000, CS instruction GTT PTE
(WW) intel(0): Existing errors found in hardware state.
(II) intel(0): Output configuration:
(II) intel(0): Pipe A is on
(II) intel(0): Display plane A is now enabled and connected to pipe A.
(II) intel(0): Pipe B is off
(II) intel(0): Display plane B is now disabled and connected to pipe B.
(II) intel(0): Output VGA is connected to pipe none
(II) intel(0): Output HDMI-1 is connected to pipe A
(II) intel(0): Output HDMI-2 is connected to pipe none
(II) intel(0): RandR 1.2 enabled, ignore the following RandR disabled message.
(II) intel(0): DPMS enabled
(==) intel(0): Intel XvMC decoder disabled
(II) intel(0): Set up textured video
(II) intel(0): direct rendering: DRI2 Enabled
(--) RandR disabled
(II) Initializing built-in extension Generic Event Extension
(II) Initializing built-in extension SHAPE
(II) Initializing built-in extension MIT-SHM
(II) Initializing built-in extension XInputExtension
(II) Initializing built-in extension XTEST
(II) Initializing built-in extension BIG-REQUESTS
(II) Initializing built-in extension SYNC
(II) Initializing built-in extension XKEYBOARD
(II) Initializing built-in extension XC-MISC
(II) Initializing built-in extension XINERAMA
(II) Initializing built-in extension XFIXES
(II) Initializing built-in extension RENDER
(II) Initializing built-in extension RANDR
(II) Initializing built-in extension COMPOSITE
(II) Initializing built-in extension DAMAGE
SELinux: Disabled on system, not enabling in X server
(II) AIGLX: enabled GLX_MESA_copy_sub_buffer
(II) AIGLX: enabled GLX_SGI_swap_control and GLX_MESA_swap_control
(II) AIGLX: GLX_EXT_texture_from_pixmap backed by buffer objects
(II) AIGLX: Loaded and initialized /usr/lib/dri/i965_dri.so
(II) GLX: Initialized DRI2 GL provider for screen 0
(II) intel(0): Setting screen physical size to 708 x 398
(II) config/hal: Adding input device Winbond CIR
(II) LoadModule: "evdev"
(II) Loading /usr/lib/xorg/modules/input//evdev_drv.so
(II) Module evdev: vendor="X.Org Foundation"
compiled for 1.6.3, module version = 2.2.5
Module class: X.Org XInput Driver
ABI class: X.Org XInput driver, version 4.0
(**) Winbond CIR: always reports core events
(**) Winbond CIR: Device: "/dev/input/event3"
(II) Winbond CIR: Found keys
(II) Winbond CIR: Configuring as keyboard
(II) XINPUT: Adding extended input device "Winbond CIR" (type: KEYBOARD)
(**) Option "xkb_rules" "evdev"
(**) Option "xkb_model" "pc104"
(**) Option "xkb_layout" "us"
(II) config/hal: Adding input device Power Button
(**) Power Button: always reports core events
(**) Power Button: Device: "/dev/input/event2"
(II) Power Button: Found keys
(II) Power Button: Configuring as keyboard
(II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD)
(**) Option "xkb_rules" "evdev"
(**) Option "xkb_model" "pc104"
(**) Option "xkb_layout" "us"
(II) config/hal: Adding input device Macintosh mouse button emulation
(**) Macintosh mouse button emulation: always reports core events
(**) Macintosh mouse button emulation: Device: "/dev/input/event0"
(II) Macintosh mouse button emulation: Found 3 mouse buttons
(II) Macintosh mouse button emulation: Found x and y relative axes
(II) Macintosh mouse button emulation: Configuring as mouse
(**) Macintosh mouse button emulation: YAxisMapping: buttons 4 and 5
(**) Macintosh mouse button emulation: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
(II) XINPUT: Adding extended input device "Macintosh mouse button emulation" (type: MOUSE)
(**) Macintosh mouse button emulation: (accel) keeping acceleration scheme 1
(**) Macintosh mouse button emulation: (accel) filter chain progression: 2.00
(**) Macintosh mouse button emulation: (accel) filter stage 0: 20.00 ms
(**) Macintosh mouse button emulation: (accel) set acceleration profile 0
(II) Macintosh mouse button emulation: initialized for relative axes.
(II) config/hal: Adding input device Power Button
(**) Power Button: always reports core events
(**) Power Button: Device: "/dev/input/event1"
(II) Power Button: Found keys
(II) Power Button: Configuring as keyboard
(II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD)
(**) Option "xkb_rules" "evdev"
(**) Option "xkb_model" "pc104"
(**) Option "xkb_layout" "us"
(II) intel(0): EDID for output VGA
(II) intel(0): EDID for output HDMI-1
(II) intel(0): Manufacturer: MJI Model: 11 Serial#: 0
(II) intel(0): Year: 2007 Week: 0
(II) intel(0): EDID Version: 1.3
(II) intel(0): Digital Display Input
(II) intel(0): Indeterminate output size
(II) intel(0): Gamma: 2.20
(II) intel(0): No DPMS capabilities specified
(II) intel(0): Supported color encodings: RGB 4:4:4 YCrCb 4:4:4
(II) intel(0): First detailed timing is preferred mode
(II) intel(0): redX: 0.640 redY: 0.330 greenX: 0.300 greenY: 0.600
(II) intel(0): blueX: 0.150 blueY: 0.060 whiteX: 0.312 whiteY: 0.329
(II) intel(0): Supported established timings:
(II) intel(0): 640x480 at 60Hz
(II) intel(0): Manufacturer's mask: 0
(II) intel(0): Supported detailed timing:
(II) intel(0): clock: 74.2 MHz Image Size: 708 x 398 mm
(II) intel(0): h_active: 1920 h_sync: 2008 h_sync_end 2052 h_blank_end 2200 h_border: 0
(II) intel(0): v_active: 540 v_sync: 542 v_sync_end 547 v_blanking: 562 v_border: 0
(II) intel(0): Supported detailed timing:
(II) intel(0): clock: 74.2 MHz Image Size: 708 x 398 mm
(II) intel(0): h_active: 1920 h_sync: 2448 h_sync_end 2492 h_blank_end 2640 h_border: 0
(II) intel(0): v_active: 540 v_sync: 542 v_sync_end 547 v_blanking: 562 v_border: 0
(II) intel(0): Ranges: V min: 49 V max: 61 Hz, H min: 15 H max: 46 kHz, PixClock max 80 MHz
(II) intel(0): Monitor name: SR8002 HDMI2
(II) intel(0): Number of EDID sections to follow: 1
(II) intel(0): EDID (in hex):
(II) intel(0): 00ffffffffffff003549110000000000
(II) intel(0): 00110103800000780aee91a3544c9926
(II) intel(0): 0f505420000001010101010101010101
(II) intel(0): 010101010101011d8018711c1620582c
(II) intel(0): 2500c48e2100009e011d80d0721c1620
(II) intel(0): 102c2580c48e2100009e000000fd0031
(II) intel(0): 3d0f2e08000a202020202020000000fc
(II) intel(0): 005352383030322048444d49320a0141
(II) intel(0): 020348725f8594041302110312010615
(II) intel(0): 07160e0f1d1e101f0a0b191a0c0d1b1c
(II) intel(0): 2324252638097f070f7f071507503d07
(II) intel(0): c04d02005706005f7e01677e00834f00
(II) intel(0): 0066030c00200080011d007251d01e20
(II) intel(0): 6e285500c48e2100001e011d00bc52d0
(II) intel(0): 1e20b8285540c48e2100001e8c0ad08a
(II) intel(0): 20e02d10103e9600c48e210000180037
(II) intel(0): EDID vendor "MJI", prod id 17
(II) intel(0): Using EDID range info for horizontal sync
(II) intel(0): Using EDID range info for vertical refresh
(II) intel(0): Printing DDC gathered Modelines:
(II) intel(0): Modeline "1920x540"x0.0 74.25 1920 2008 2052 2200 540 542 547 562 interlace +hsync +vsync (33.8 kHz)
(II) intel(0): Modeline "1920x540"x0.0 74.25 1920 2448 2492 2640 540 542 547 562 interlace +hsync +vsync (28.1 kHz)
(II) intel(0): Modeline "640x480"x0.0 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz)
(II) intel(0): EDID vendor "MJI", prod id 17
(II) intel(0): Printing probed modes for output HDMI-1
(II) intel(0): Modeline "1920x540"x120.1 74.25 1920 2008 2052 2200 540 542 547 562 interlace +hsync +vsync (33.8 kHz)
(II) intel(0): Modeline "1920x540"x100.1 74.25 1920 2448 2492 2640 540 542 547 562 interlace +hsync +vsync (28.1 kHz)
(II) intel(0): Modeline "640x480"x59.9 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz)
(II) intel(0): EDID for output HDMI-2
(II) intel(0): EDID for output VGA
(II) intel(0): EDID for output HDMI-1
(II) intel(0): Manufacturer: MJI Model: 11 Serial#: 0
(II) intel(0): Year: 2007 Week: 0
(II) intel(0): EDID Version: 1.3
(II) intel(0): Digital Display Input
(II) intel(0): Indeterminate output size
(II) intel(0): Gamma: 2.20
(II) intel(0): No DPMS capabilities specified
(II) intel(0): Supported color encodings: RGB 4:4:4 YCrCb 4:4:4
(II) intel(0): First detailed timing is preferred mode
(II) intel(0): redX: 0.640 redY: 0.330 greenX: 0.300 greenY: 0.600
(II) intel(0): blueX: 0.150 blueY: 0.060 whiteX: 0.312 whiteY: 0.329
(II) intel(0): Supported established timings:
(II) intel(0): 640x480 at 60Hz
(II) intel(0): Manufacturer's mask: 0
(II) intel(0): Supported detailed timing:
(II) intel(0): clock: 74.2 MHz Image Size: 708 x 398 mm
(II) intel(0): h_active: 1920 h_sync: 2008 h_sync_end 2052 h_blank_end 2200 h_border: 0
(II) intel(0): v_active: 540 v_sync: 542 v_sync_end 547 v_blanking: 562 v_border: 0
(II) intel(0): Supported detailed timing:
(II) intel(0): clock: 74.2 MHz Image Size: 708 x 398 mm
(II) intel(0): h_active: 1920 h_sync: 2448 h_sync_end 2492 h_blank_end 2640 h_border: 0
(II) intel(0): v_active: 540 v_sync: 542 v_sync_end 547 v_blanking: 562 v_border: 0
(II) intel(0): Ranges: V min: 49 V max: 61 Hz, H min: 15 H max: 46 kHz, PixClock max 80 MHz
(II) intel(0): Monitor name: SR8002 HDMI2
(II) intel(0): Number of EDID sections to follow: 1
(II) intel(0): EDID (in hex):
(II) intel(0): 00ffffffffffff003549110000000000
(II) intel(0): 00110103800000780aee91a3544c9926
(II) intel(0): 0f505420000001010101010101010101
(II) intel(0): 010101010101011d8018711c1620582c
(II) intel(0): 2500c48e2100009e011d80d0721c1620
(II) intel(0): 102c2580c48e2100009e000000fd0031
(II) intel(0): 3d0f2e08000a202020202020000000fc
(II) intel(0): 005352383030322048444d49320a0141
(II) intel(0): 020348725f8594041302110312010615
(II) intel(0): 07160e0f1d1e101f0a0b191a0c0d1b1c
(II) intel(0): 2324252638097f070f7f071507503d07
(II) intel(0): c04d02005706005f7e01677e00834f00
(II) intel(0): 0066030c00200080011d007251d01e20
(II) intel(0): 6e285500c48e2100001e011d00bc52d0
(II) intel(0): 1e20b8285540c48e2100001e8c0ad08a
(II) intel(0): 20e02d10103e9600c48e210000180037
(II) intel(0): EDID vendor "MJI", prod id 17
(II) intel(0): Using hsync ranges from config file
(II) intel(0): Using vrefresh ranges from config file
(II) intel(0): Printing DDC gathered Modelines:
(II) intel(0): Modeline "1920x540"x0.0 74.25 1920 2008 2052 2200 540 542 547 562 interlace +hsync +vsync (33.8 kHz)
(II) intel(0): Modeline "1920x540"x0.0 74.25 1920 2448 2492 2640 540 542 547 562 interlace +hsync +vsync (28.1 kHz)
(II) intel(0): Modeline "640x480"x0.0 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz)
(II) intel(0): EDID vendor "MJI", prod id 17
(II) intel(0): Printing probed modes for output HDMI-1
(II) intel(0): Modeline "1920x540"x120.1 74.25 1920 2008 2052 2200 540 542 547 562 interlace +hsync +vsync (33.8 kHz)
(II) intel(0): Modeline "1920x540"x100.1 74.25 1920 2448 2492 2640 540 542 547 562 interlace +hsync +vsync (28.1 kHz)
(II) intel(0): Modeline "640x480"x59.9 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz)
(II) intel(0): EDID for output HDMI-2
-------------- next part --------------
X.Org X Server 1.6.3
Release Date: 2009-7-31
X Protocol Version 11, Revision 0
Build Operating System: Linux 2.6.30-1-amd64 x86_64 Debian
Current Operating System: Linux scott 2.6.30-1-amd64 #1 SMP Fri Aug 7 23:20:43 CEST 2009 x86_64
Build Date: 31 August 2009 11:11:11PM
xorg-server 2:1.6.3-1 (david at hardeman.nu)
Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.log", Time: Sat Sep 5 19:57:13 2009
(II) Loader magic: 0x34c0
(II) Module ABI versions:
X.Org ANSI C Emulation: 0.4
X.Org Video Driver: 5.0
X.Org XInput driver : 4.0
X.Org Server Extension : 2.0
(II) Loader running on linux
(++) using VT number 7
(--) PCI:*(0:0:2:0) 8086:2e22:8086:5003 Intel Corporation 4 Series Chipset Integrated Graphics Controller rev 3, Mem @ 0xff400000/4194304, 0xd0000000/268435456, I/O @ 0x0000f1c0/8
(==) Using default built-in configuration (39 lines)
(==) --- Start of built-in configuration ---
Section "Device"
Identifier "Builtin Default intel Device 0"
Driver "intel"
EndSection
Section "Screen"
Identifier "Builtin Default intel Screen 0"
Device "Builtin Default intel Device 0"
EndSection
Section "Device"
Identifier "Builtin Default i810 Device 0"
Driver "i810"
EndSection
Section "Screen"
Identifier "Builtin Default i810 Screen 0"
Device "Builtin Default i810 Device 0"
EndSection
Section "Device"
Identifier "Builtin Default vesa Device 0"
Driver "vesa"
EndSection
Section "Screen"
Identifier "Builtin Default vesa Screen 0"
Device "Builtin Default vesa Device 0"
EndSection
Section "Device"
Identifier "Builtin Default fbdev Device 0"
Driver "fbdev"
EndSection
Section "Screen"
Identifier "Builtin Default fbdev Screen 0"
Device "Builtin Default fbdev Device 0"
EndSection
Section "ServerLayout"
Identifier "Builtin Default Layout"
Screen "Builtin Default intel Screen 0"
Screen "Builtin Default i810 Screen 0"
Screen "Builtin Default vesa Screen 0"
Screen "Builtin Default fbdev Screen 0"
EndSection
(==) --- End of built-in configuration ---
(==) ServerLayout "Builtin Default Layout"
(**) |-->Screen "Builtin Default intel Screen 0" (0)
(**) | |-->Monitor "<default monitor>"
(**) | |-->Device "Builtin Default intel Device 0"
(==) No monitor specified for screen "Builtin Default intel Screen 0".
Using a default monitor configuration.
(**) |-->Screen "Builtin Default i810 Screen 0" (1)
(**) | |-->Monitor "<default monitor>"
(**) | |-->Device "Builtin Default i810 Device 0"
(==) No monitor specified for screen "Builtin Default i810 Screen 0".
Using a default monitor configuration.
(**) |-->Screen "Builtin Default vesa Screen 0" (2)
(**) | |-->Monitor "<default monitor>"
(**) | |-->Device "Builtin Default vesa Device 0"
(==) No monitor specified for screen "Builtin Default vesa Screen 0".
Using a default monitor configuration.
(**) |-->Screen "Builtin Default fbdev Screen 0" (3)
(**) | |-->Monitor "<default monitor>"
(**) | |-->Device "Builtin Default fbdev Device 0"
(==) No monitor specified for screen "Builtin Default fbdev Screen 0".
Using a default monitor configuration.
(==) Automatically adding devices
(==) Automatically enabling devices
(WW) The directory "/usr/share/fonts/X11/cyrillic" does not exist.
Entry deleted from font path.
(WW) The directory "/usr/share/fonts/X11/75dpi/" does not exist.
Entry deleted from font path.
(WW) The directory "/usr/share/fonts/X11/Type1" does not exist.
Entry deleted from font path.
(WW) The directory "/usr/share/fonts/X11/75dpi" does not exist.
Entry deleted from font path.
(WW) The directory "/var/lib/defoma/x-ttcidfont-conf.d/dirs/TrueType" does not exist.
Entry deleted from font path.
(==) FontPath set to:
/usr/share/fonts/X11/misc,
/usr/share/fonts/X11/100dpi/:unscaled,
/usr/share/fonts/X11/100dpi,
built-ins
(==) ModulePath set to "/usr/lib/xorg/modules"
(II) Cannot locate a core pointer device.
(II) Cannot locate a core keyboard device.
(II) The server relies on HAL to provide the list of input devices.
If no devices become available, reconfigure HAL or disable AllowEmptyInput.
(II) Open ACPI successful (/var/run/acpid.socket)
(II) System resource ranges:
[0] -1 0 0xffffffff - 0xffffffff (0x1) MX[B]
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[4] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[5] -1 0 0x00000000 - 0x00000000 (0x1) IX[B]
(II) LoadModule: "extmod"
(II) Loading /usr/lib/xorg/modules/extensions//libextmod.so
(II) Module extmod: vendor="X.Org Foundation"
compiled for 1.6.3, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension SELinux
(II) Loading extension MIT-SCREEN-SAVER
(II) Loading extension XFree86-VidModeExtension
(II) Loading extension XFree86-DGA
(II) Loading extension DPMS
(II) Loading extension XVideo
(II) Loading extension XVideo-MotionCompensation
(II) Loading extension X-Resource
(II) LoadModule: "dbe"
(II) Loading /usr/lib/xorg/modules/extensions//libdbe.so
(II) Module dbe: vendor="X.Org Foundation"
compiled for 1.6.3, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension DOUBLE-BUFFER
(II) LoadModule: "glx"
(II) Loading /usr/lib/xorg/modules/extensions//libglx.so
(II) Module glx: vendor="X.Org Foundation"
compiled for 1.6.3, module version = 1.0.0
ABI class: X.Org Server Extension, version 2.0
(==) AIGLX enabled
(II) Loading extension GLX
(II) LoadModule: "record"
(II) Loading /usr/lib/xorg/modules/extensions//librecord.so
(II) Module record: vendor="X.Org Foundation"
compiled for 1.6.3, module version = 1.13.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension RECORD
(II) LoadModule: "dri"
(II) Loading /usr/lib/xorg/modules/extensions//libdri.so
(II) Module dri: vendor="X.Org Foundation"
compiled for 1.6.3, module version = 1.0.0
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension XFree86-DRI
(II) LoadModule: "dri2"
(II) Loading /usr/lib/xorg/modules/extensions//libdri2.so
(II) Module dri2: vendor="X.Org Foundation"
compiled for 1.6.3, module version = 1.1.0
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension DRI2
(II) LoadModule: "intel"
(II) Loading /usr/lib/xorg/modules/drivers//intel_drv.so
(II) Module intel: vendor="X.Org Foundation"
compiled for 1.6.3, module version = 2.8.1
Module class: X.Org Video Driver
ABI class: X.Org Video Driver, version 5.0
(II) LoadModule: "i810"
(WW) Warning, couldn't open module i810
(II) UnloadModule: "i810"
(EE) Failed to load module "i810" (module does not exist, 0)
(II) LoadModule: "vesa"
(WW) Warning, couldn't open module vesa
(II) UnloadModule: "vesa"
(EE) Failed to load module "vesa" (module does not exist, 0)
(II) LoadModule: "fbdev"
(WW) Warning, couldn't open module fbdev
(II) UnloadModule: "fbdev"
(EE) Failed to load module "fbdev" (module does not exist, 0)
(II) intel: Driver for Intel Integrated Graphics Chipsets: i810,
i810-dc100, i810e, i815, i830M, 845G, 852GM/855GM, 865G, 915G,
E7221 (i915), 915GM, 945G, 945GM, 945GME, IGD_GM, IGD_G, 965G, G35,
965Q, 946GZ, 965GM, 965GME/GLE, G33, Q35, Q33,
Mobile Intel® GM45 Express Chipset,
Intel Integrated Graphics Device, G45/G43, Q45/Q43, G41, IGDNG_D,
IGDNG_M
(II) Primary Device is: PCI 00 at 00:02:0
(II) resource ranges after xf86ClaimFixedResources() call:
[0] -1 0 0xffffffff - 0xffffffff (0x1) MX[B]
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[4] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[5] -1 0 0x00000000 - 0x00000000 (0x1) IX[B]
(II) resource ranges after probing:
[0] -1 0 0xffffffff - 0xffffffff (0x1) MX[B]
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[4] 0 0 0x000a0000 - 0x000affff (0x10000) MS[B]
[5] 0 0 0x000b0000 - 0x000b7fff (0x8000) MS[B]
[6] 0 0 0x000b8000 - 0x000bffff (0x8000) MS[B]
[7] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[8] -1 0 0x00000000 - 0x00000000 (0x1) IX[B]
[9] 0 0 0x000003b0 - 0x000003bb (0xc) IS[B]
[10] 0 0 0x000003c0 - 0x000003df (0x20) IS[B]
(II) Loading sub module "vgahw"
(II) LoadModule: "vgahw"
(II) Loading /usr/lib/xorg/modules//libvgahw.so
(II) Module vgahw: vendor="X.Org Foundation"
compiled for 1.6.3, module version = 0.1.0
ABI class: X.Org Video Driver, version 5.0
(II) Loading sub module "ramdac"
(II) LoadModule: "ramdac"
(II) Module "ramdac" already built-in
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 9, (OK)
drmOpenByBusid: Searching for BusID pci:0000:00:02.0
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 9, (OK)
drmOpenByBusid: drmOpenMinor returns 9
drmOpenByBusid: drmGetBusid reports pci:0000:00:02.0
(II) intel(0): Creating default Display subsection in Screen section
"Builtin Default intel Screen 0" for depth/fbbpp 24/32
(==) intel(0): Depth 24, (--) framebuffer bpp 32
(==) intel(0): RGB weight 888
(==) intel(0): Default visual is TrueColor
(II) intel(0): Integrated Graphics Chipset: Intel(R) G45/G43
(--) intel(0): Chipset: "G45/G43"
(--) intel(0): Linear framebuffer at 0xD0000000
(--) intel(0): IO registers at addr 0xFF400000 size 4194304
(WW) intel(0): libpciaccess reported 0 rom size, guessing 64kB
(II) intel(0): No SDVO device is found in VBT
(II) intel(0): 2 display pipes available.
(II) Loading sub module "ddc"
(II) LoadModule: "ddc"
(II) Module "ddc" already built-in
(II) Loading sub module "i2c"
(II) LoadModule: "i2c"
(II) Module "i2c" already built-in
(II) intel(0): Output VGA has no monitor section
(II) intel(0): I2C bus "SDVOCTRL_E for SDVOB" initialized.
(II) intel(0): I2C device "SDVOCTRL_E for SDVOB:SDVO Controller B" registered at address 0x70.
(II) intel(0): No SDVO device found on SDVOB
(II) intel(0): I2C device "SDVOCTRL_E for SDVOB:SDVO Controller B" removed.
(II) intel(0): I2C bus "SDVOCTRL_E for SDVOB" removed.
(II) intel(0): Output HDMI-1 has no monitor section
(II) intel(0): I2C bus "HDMIDDC_B" initialized.
(II) intel(0): HDMI output 1 detected
(II) intel(0): I2C bus "SDVOCTRL_E for SDVOC" initialized.
(II) intel(0): I2C device "SDVOCTRL_E for SDVOC:SDVO Controller C" registered at address 0x72.
(II) intel(0): No SDVO device found on SDVOC
(II) intel(0): I2C device "SDVOCTRL_E for SDVOC:SDVO Controller C" removed.
(II) intel(0): I2C bus "SDVOCTRL_E for SDVOC" removed.
(II) intel(0): Output HDMI-2 has no monitor section
(II) intel(0): I2C bus "HDMIDDC_C" initialized.
(II) intel(0): HDMI output 2 detected
(II) intel(0): EDID for output VGA
(II) intel(0): I2C device "HDMIDDC_B:E-EDID segment register" registered at address 0x60.
(II) intel(0): I2C device "HDMIDDC_B:ddc2" registered at address 0xA0.
(II) Quirked EDID physical size to 71x40 cm
(II) Quirked EDID physical size to 71x40 cm
(II) intel(0): EDID for output HDMI-1
(II) intel(0): Manufacturer: MJI Model: 11 Serial#: 0
(II) intel(0): Year: 2007 Week: 0
(II) intel(0): EDID Version: 1.3
(II) intel(0): Digital Display Input
(II) intel(0): Max Image Size [cm]: horiz.: 71 vert.: 40
(II) intel(0): Gamma: 2.20
(II) intel(0): No DPMS capabilities specified
(II) intel(0): Supported color encodings: RGB 4:4:4 YCrCb 4:4:4
(II) intel(0): First detailed timing is preferred mode
(II) intel(0): redX: 0.640 redY: 0.330 greenX: 0.300 greenY: 0.600
(II) intel(0): blueX: 0.150 blueY: 0.060 whiteX: 0.312 whiteY: 0.329
(II) intel(0): Supported established timings:
(II) intel(0): 640x480 at 60Hz
(II) intel(0): 800x600 at 60Hz
(II) intel(0): 1024x768 at 60Hz
(II) intel(0): Manufacturer's mask: 0
(II) intel(0): Supported standard timings:
(II) intel(0): #0: hsize: 1280 vsize 1024 refresh: 60 vid: 32897
(II) intel(0): #1: hsize: 1600 vsize 1200 refresh: 60 vid: 16553
(II) intel(0): Supported detailed timing:
(II) intel(0): clock: 148.5 MHz Image Size: 160 x 90 mm
(II) intel(0): h_active: 1920 h_sync: 2008 h_sync_end 2052 h_blank_end 2200 h_border: 0
(II) intel(0): v_active: 1080 v_sync: 1084 v_sync_end 1089 v_blanking: 1125 v_border: 0
(II) intel(0): Supported detailed timing:
(II) intel(0): clock: 74.2 MHz Image Size: 708 x 398 mm
(II) intel(0): h_active: 1920 h_sync: 2008 h_sync_end 2052 h_blank_end 2200 h_border: 0
(II) intel(0): v_active: 540 v_sync: 542 v_sync_end 547 v_blanking: 562 v_border: 0
(II) intel(0): Ranges: V min: 23 V max: 61 Hz, H min: 26 H max: 76 kHz, PixClock max 230 MHz
(II) intel(0): Monitor name: SR8002 HDMI2
(II) intel(0): Number of EDID sections to follow: 1
(II) intel(0): EDID (in hex):
(II) intel(0): 00ffffffffffff003549110000000000
(II) intel(0): 00110103801009780aee91a3544c9926
(II) intel(0): 0f50542108008180a940010101010101
(II) intel(0): 010101010101023a801871382d40582c
(II) intel(0): 4500a05a0000001e011d8018711c1620
(II) intel(0): 582c2500c48e2100009e000000fd0017
(II) intel(0): 3d1a4c17000a202020202020000000fc
(II) intel(0): 005352383030322048444d49320a0174
(II) intel(0): 020341f150901f041305140312202122
(II) intel(0): 0e0f241e2638097f070f7f071507503d
(II) intel(0): 07c04d02005706005f7e01677e00834f
(II) intel(0): 0000e3050301e2e26267030c002200b8
(II) intel(0): 2d011d80d0721c1620102c2580c48e21
(II) intel(0): 00009e8c0ad08a20e02d10103e9600c4
(II) intel(0): 8e210000188c0ad090204031200c4055
(II) intel(0): 00c48e2100001800000000000000006e
(II) intel(0): EDID vendor "MJI", prod id 17
(II) intel(0): Printing probed modes for output HDMI-1
(II) intel(0): Modeline "1920x1080"x60.0 148.50 1920 2008 2052 2200 1080 1084 1089 1125 +hsync +vsync (67.5 kHz)
(II) intel(0): Modeline "1600x1200"x60.0 162.00 1600 1664 1856 2160 1200 1201 1204 1250 +hsync +vsync (75.0 kHz)
(II) intel(0): Modeline "1280x1024"x60.0 108.00 1280 1328 1440 1688 1024 1025 1028 1066 +hsync +vsync (64.0 kHz)
(II) intel(0): Modeline "1920x540"x120.1 74.25 1920 2008 2052 2200 540 542 547 562 interlace +hsync +vsync (33.8 kHz)
(II) intel(0): Modeline "1024x768"x60.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz)
(II) intel(0): Modeline "800x600"x60.3 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz)
(II) intel(0): Modeline "640x480"x59.9 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz)
(II) intel(0): EDID for output HDMI-2
(II) intel(0): Output VGA disconnected
(II) intel(0): Output HDMI-1 connected
(II) intel(0): Output HDMI-2 disconnected
(II) intel(0): Using exact sizes for initial modes
(II) intel(0): Output HDMI-1 using initial mode 1920x1080
(II) intel(0): detected 512 kB GTT.
(II) intel(0): detected 32764 kB stolen memory.
(==) intel(0): video overlay key set to 0x101fe
(==) intel(0): Using gamma correction (1.0, 1.0, 1.0)
(==) intel(0): DPI set to (96, 96)
(II) Loading sub module "fb"
(II) LoadModule: "fb"
(II) Loading /usr/lib/xorg/modules//libfb.so
(II) Module fb: vendor="X.Org Foundation"
compiled for 1.6.3, module version = 1.0.0
ABI class: X.Org ANSI C Emulation, version 0.4
(II) intel(0): Comparing regs from server start up to After PreInit
(==) Depth 24 pixmap format is 32 bpp
(II) do I need RAC? No, I don't.
(II) resource ranges after preInit:
[0] -1 0 0xffffffff - 0xffffffff (0x1) MX[B]
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[4] 0 0 0x000a0000 - 0x000affff (0x10000) MS[B](OprD)
[5] 0 0 0x000b0000 - 0x000b7fff (0x8000) MS[B](OprD)
[6] 0 0 0x000b8000 - 0x000bffff (0x8000) MS[B](OprD)
[7] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[8] -1 0 0x00000000 - 0x00000000 (0x1) IX[B]
[9] 0 0 0x000003b0 - 0x000003bb (0xc) IS[B](OprU)
[10] 0 0 0x000003c0 - 0x000003df (0x20) IS[B](OprU)
(II) intel(0): Kernel reported 1248000 total, 1 used
(II) intel(0): I830CheckAvailableMemory: 4991996 kB available
(II) intel(0): [DRI2] Setup complete
(**) intel(0): Framebuffer compression disabled
(**) intel(0): Tiling enabled
(**) intel(0): SwapBuffers wait enabled
(==) intel(0): VideoRam: 262144 KB
(II) intel(0): Attempting memory allocation with tiled buffers.
(II) intel(0): Tiled allocation successful.
(II) intel(0): vgaHWGetIOBase: hwp->IOBase is 0x03d0, hwp->PIOOffset is 0x0000
(II) UXA(0): Driver registered support for the following operations:
(II) solid
(II) copy
(II) composite (RENDER acceleration)
(==) intel(0): Backing store disabled
(==) intel(0): Silken mouse enabled
(II) intel(0): Initializing HW Cursor
(II) intel(0): Fixed memory allocation layout:
(II) intel(0): 0x01fff000: end of stolen memory
(II) intel(0): 0x01fff000-0x0fffffff: DRI memory manager (229380 kB)
(II) intel(0): 0x10000000: end of aperture
(II) intel(0): BO memory allocation layout:
(II) intel(0): 0x01fff000: start of memory manager
(II) intel(0): 0x02020000-0x02808fff: front buffer (8100 kB) X tiled
(II) intel(0): 0x02820000-0x02829fff: HW cursors (40 kB)
(II) intel(0): 0x10000000: end of memory manager
(WW) intel(0): ESR is 0x00000011, page table error
(WW) intel(0): PGTBL_ER is 0x00100000, CS instruction GTT PTE
(WW) intel(0): Existing errors found in hardware state.
(II) intel(0): Output configuration:
(II) intel(0): Pipe A is on
(II) intel(0): Display plane A is now enabled and connected to pipe A.
(II) intel(0): Pipe B is off
(II) intel(0): Display plane B is now disabled and connected to pipe B.
(II) intel(0): Output VGA is connected to pipe none
(II) intel(0): Output HDMI-1 is connected to pipe A
(II) intel(0): Output HDMI-2 is connected to pipe none
(II) intel(0): RandR 1.2 enabled, ignore the following RandR disabled message.
(II) intel(0): DPMS enabled
(==) intel(0): Intel XvMC decoder disabled
(II) intel(0): Set up textured video
(II) intel(0): direct rendering: DRI2 Enabled
(--) RandR disabled
(II) Initializing built-in extension Generic Event Extension
(II) Initializing built-in extension SHAPE
(II) Initializing built-in extension MIT-SHM
(II) Initializing built-in extension XInputExtension
(II) Initializing built-in extension XTEST
(II) Initializing built-in extension BIG-REQUESTS
(II) Initializing built-in extension SYNC
(II) Initializing built-in extension XKEYBOARD
(II) Initializing built-in extension XC-MISC
(II) Initializing built-in extension XINERAMA
(II) Initializing built-in extension XFIXES
(II) Initializing built-in extension RENDER
(II) Initializing built-in extension RANDR
(II) Initializing built-in extension COMPOSITE
(II) Initializing built-in extension DAMAGE
SELinux: Disabled on system, not enabling in X server
(II) AIGLX: enabled GLX_MESA_copy_sub_buffer
(II) AIGLX: enabled GLX_SGI_swap_control and GLX_MESA_swap_control
(II) AIGLX: GLX_EXT_texture_from_pixmap backed by buffer objects
(II) AIGLX: Loaded and initialized /usr/lib/dri/i965_dri.so
(II) GLX: Initialized DRI2 GL provider for screen 0
(II) intel(0): Setting screen physical size to 160 x 90
(II) config/hal: Adding input device Winbond CIR
(II) LoadModule: "evdev"
(II) Loading /usr/lib/xorg/modules/input//evdev_drv.so
(II) Module evdev: vendor="X.Org Foundation"
compiled for 1.6.3, module version = 2.2.5
Module class: X.Org XInput Driver
ABI class: X.Org XInput driver, version 4.0
(**) Winbond CIR: always reports core events
(**) Winbond CIR: Device: "/dev/input/event3"
(II) Winbond CIR: Found keys
(II) Winbond CIR: Configuring as keyboard
(II) XINPUT: Adding extended input device "Winbond CIR" (type: KEYBOARD)
(**) Option "xkb_rules" "evdev"
(**) Option "xkb_model" "pc104"
(**) Option "xkb_layout" "us"
(II) config/hal: Adding input device Power Button
(**) Power Button: always reports core events
(**) Power Button: Device: "/dev/input/event2"
(II) Power Button: Found keys
(II) Power Button: Configuring as keyboard
(II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD)
(**) Option "xkb_rules" "evdev"
(**) Option "xkb_model" "pc104"
(**) Option "xkb_layout" "us"
(II) config/hal: Adding input device Macintosh mouse button emulation
(**) Macintosh mouse button emulation: always reports core events
(**) Macintosh mouse button emulation: Device: "/dev/input/event0"
(II) Macintosh mouse button emulation: Found 3 mouse buttons
(II) Macintosh mouse button emulation: Found x and y relative axes
(II) Macintosh mouse button emulation: Configuring as mouse
(**) Macintosh mouse button emulation: YAxisMapping: buttons 4 and 5
(**) Macintosh mouse button emulation: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
(II) XINPUT: Adding extended input device "Macintosh mouse button emulation" (type: MOUSE)
(**) Macintosh mouse button emulation: (accel) keeping acceleration scheme 1
(**) Macintosh mouse button emulation: (accel) filter chain progression: 2.00
(**) Macintosh mouse button emulation: (accel) filter stage 0: 20.00 ms
(**) Macintosh mouse button emulation: (accel) set acceleration profile 0
(II) Macintosh mouse button emulation: initialized for relative axes.
(II) config/hal: Adding input device Power Button
(**) Power Button: always reports core events
(**) Power Button: Device: "/dev/input/event1"
(II) Power Button: Found keys
(II) Power Button: Configuring as keyboard
(II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD)
(**) Option "xkb_rules" "evdev"
(**) Option "xkb_model" "pc104"
(**) Option "xkb_layout" "us"
(II) intel(0): EDID for output VGA
(II) Quirked EDID physical size to 71x40 cm
(II) Quirked EDID physical size to 71x40 cm
(II) intel(0): EDID for output HDMI-1
(II) intel(0): Manufacturer: MJI Model: 11 Serial#: 0
(II) intel(0): Year: 2007 Week: 0
(II) intel(0): EDID Version: 1.3
(II) intel(0): Digital Display Input
(II) intel(0): Max Image Size [cm]: horiz.: 71 vert.: 40
(II) intel(0): Gamma: 2.20
(II) intel(0): No DPMS capabilities specified
(II) intel(0): Supported color encodings: RGB 4:4:4 YCrCb 4:4:4
(II) intel(0): First detailed timing is preferred mode
(II) intel(0): redX: 0.640 redY: 0.330 greenX: 0.300 greenY: 0.600
(II) intel(0): blueX: 0.150 blueY: 0.060 whiteX: 0.312 whiteY: 0.329
(II) intel(0): Supported established timings:
(II) intel(0): 640x480 at 60Hz
(II) intel(0): 800x600 at 60Hz
(II) intel(0): 1024x768 at 60Hz
(II) intel(0): Manufacturer's mask: 0
(II) intel(0): Supported standard timings:
(II) intel(0): #0: hsize: 1280 vsize 1024 refresh: 60 vid: 32897
(II) intel(0): #1: hsize: 1600 vsize 1200 refresh: 60 vid: 16553
(II) intel(0): Supported detailed timing:
(II) intel(0): clock: 148.5 MHz Image Size: 160 x 90 mm
(II) intel(0): h_active: 1920 h_sync: 2008 h_sync_end 2052 h_blank_end 2200 h_border: 0
(II) intel(0): v_active: 1080 v_sync: 1084 v_sync_end 1089 v_blanking: 1125 v_border: 0
(II) intel(0): Supported detailed timing:
(II) intel(0): clock: 74.2 MHz Image Size: 708 x 398 mm
(II) intel(0): h_active: 1920 h_sync: 2008 h_sync_end 2052 h_blank_end 2200 h_border: 0
(II) intel(0): v_active: 540 v_sync: 542 v_sync_end 547 v_blanking: 562 v_border: 0
(II) intel(0): Ranges: V min: 23 V max: 61 Hz, H min: 26 H max: 76 kHz, PixClock max 230 MHz
(II) intel(0): Monitor name: SR8002 HDMI2
(II) intel(0): Number of EDID sections to follow: 1
(II) intel(0): EDID (in hex):
(II) intel(0): 00ffffffffffff003549110000000000
(II) intel(0): 00110103801009780aee91a3544c9926
(II) intel(0): 0f50542108008180a940010101010101
(II) intel(0): 010101010101023a801871382d40582c
(II) intel(0): 4500a05a0000001e011d8018711c1620
(II) intel(0): 582c2500c48e2100009e000000fd0017
(II) intel(0): 3d1a4c17000a202020202020000000fc
(II) intel(0): 005352383030322048444d49320a0174
(II) intel(0): 020341f150901f041305140312202122
(II) intel(0): 0e0f241e2638097f070f7f071507503d
(II) intel(0): 07c04d02005706005f7e01677e00834f
(II) intel(0): 0000e3050301e2e26267030c002200b8
(II) intel(0): 2d011d80d0721c1620102c2580c48e21
(II) intel(0): 00009e8c0ad08a20e02d10103e9600c4
(II) intel(0): 8e210000188c0ad090204031200c4055
(II) intel(0): 00c48e2100001800000000000000006e
(II) intel(0): EDID vendor "MJI", prod id 17
(II) intel(0): Using EDID range info for horizontal sync
(II) intel(0): Using EDID range info for vertical refresh
(II) intel(0): Printing DDC gathered Modelines:
(II) intel(0): Modeline "1920x1080"x0.0 148.50 1920 2008 2052 2200 1080 1084 1089 1125 +hsync +vsync (67.5 kHz)
(II) intel(0): Modeline "1920x540"x0.0 74.25 1920 2008 2052 2200 540 542 547 562 interlace +hsync +vsync (33.8 kHz)
(II) intel(0): Modeline "800x600"x0.0 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz)
(II) intel(0): Modeline "640x480"x0.0 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz)
(II) intel(0): Modeline "1024x768"x0.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz)
(II) intel(0): Modeline "1280x1024"x0.0 108.00 1280 1328 1440 1688 1024 1025 1028 1066 +hsync +vsync (64.0 kHz)
(II) intel(0): Modeline "1600x1200"x0.0 162.00 1600 1664 1856 2160 1200 1201 1204 1250 +hsync +vsync (75.0 kHz)
(II) intel(0): EDID vendor "MJI", prod id 17
(II) intel(0): Printing probed modes for output HDMI-1
(II) intel(0): Modeline "1920x1080"x60.0 148.50 1920 2008 2052 2200 1080 1084 1089 1125 +hsync +vsync (67.5 kHz)
(II) intel(0): Modeline "1600x1200"x60.0 162.00 1600 1664 1856 2160 1200 1201 1204 1250 +hsync +vsync (75.0 kHz)
(II) intel(0): Modeline "1280x1024"x60.0 108.00 1280 1328 1440 1688 1024 1025 1028 1066 +hsync +vsync (64.0 kHz)
(II) intel(0): Modeline "1920x540"x120.1 74.25 1920 2008 2052 2200 540 542 547 562 interlace +hsync +vsync (33.8 kHz)
(II) intel(0): Modeline "1024x768"x60.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz)
(II) intel(0): Modeline "800x600"x60.3 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz)
(II) intel(0): Modeline "640x480"x59.9 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz)
(II) intel(0): EDID for output HDMI-2
(II) intel(0): EDID for output VGA
(II) Quirked EDID physical size to 71x40 cm
(II) Quirked EDID physical size to 71x40 cm
(II) intel(0): EDID for output HDMI-1
(II) intel(0): Manufacturer: MJI Model: 11 Serial#: 0
(II) intel(0): Year: 2007 Week: 0
(II) intel(0): EDID Version: 1.3
(II) intel(0): Digital Display Input
(II) intel(0): Max Image Size [cm]: horiz.: 71 vert.: 40
(II) intel(0): Gamma: 2.20
(II) intel(0): No DPMS capabilities specified
(II) intel(0): Supported color encodings: RGB 4:4:4 YCrCb 4:4:4
(II) intel(0): First detailed timing is preferred mode
(II) intel(0): redX: 0.640 redY: 0.330 greenX: 0.300 greenY: 0.600
(II) intel(0): blueX: 0.150 blueY: 0.060 whiteX: 0.312 whiteY: 0.329
(II) intel(0): Supported established timings:
(II) intel(0): 640x480 at 60Hz
(II) intel(0): 800x600 at 60Hz
(II) intel(0): 1024x768 at 60Hz
(II) intel(0): Manufacturer's mask: 0
(II) intel(0): Supported standard timings:
(II) intel(0): #0: hsize: 1280 vsize 1024 refresh: 60 vid: 32897
(II) intel(0): #1: hsize: 1600 vsize 1200 refresh: 60 vid: 16553
(II) intel(0): Supported detailed timing:
(II) intel(0): clock: 148.5 MHz Image Size: 160 x 90 mm
(II) intel(0): h_active: 1920 h_sync: 2008 h_sync_end 2052 h_blank_end 2200 h_border: 0
(II) intel(0): v_active: 1080 v_sync: 1084 v_sync_end 1089 v_blanking: 1125 v_border: 0
(II) intel(0): Supported detailed timing:
(II) intel(0): clock: 74.2 MHz Image Size: 708 x 398 mm
(II) intel(0): h_active: 1920 h_sync: 2008 h_sync_end 2052 h_blank_end 2200 h_border: 0
(II) intel(0): v_active: 540 v_sync: 542 v_sync_end 547 v_blanking: 562 v_border: 0
(II) intel(0): Ranges: V min: 23 V max: 61 Hz, H min: 26 H max: 76 kHz, PixClock max 230 MHz
(II) intel(0): Monitor name: SR8002 HDMI2
(II) intel(0): Number of EDID sections to follow: 1
(II) intel(0): EDID (in hex):
(II) intel(0): 00ffffffffffff003549110000000000
(II) intel(0): 00110103801009780aee91a3544c9926
(II) intel(0): 0f50542108008180a940010101010101
(II) intel(0): 010101010101023a801871382d40582c
(II) intel(0): 4500a05a0000001e011d8018711c1620
(II) intel(0): 582c2500c48e2100009e000000fd0017
(II) intel(0): 3d1a4c17000a202020202020000000fc
(II) intel(0): 005352383030322048444d49320a0174
(II) intel(0): 020341f150901f041305140312202122
(II) intel(0): 0e0f241e2638097f070f7f071507503d
(II) intel(0): 07c04d02005706005f7e01677e00834f
(II) intel(0): 0000e3050301e2e26267030c002200b8
(II) intel(0): 2d011d80d0721c1620102c2580c48e21
(II) intel(0): 00009e8c0ad08a20e02d10103e9600c4
(II) intel(0): 8e210000188c0ad090204031200c4055
(II) intel(0): 00c48e2100001800000000000000006e
(II) intel(0): EDID vendor "MJI", prod id 17
(II) intel(0): Using hsync ranges from config file
(II) intel(0): Using vrefresh ranges from config file
(II) intel(0): Printing DDC gathered Modelines:
(II) intel(0): Modeline "1920x1080"x0.0 148.50 1920 2008 2052 2200 1080 1084 1089 1125 +hsync +vsync (67.5 kHz)
(II) intel(0): Modeline "1920x540"x0.0 74.25 1920 2008 2052 2200 540 542 547 562 interlace +hsync +vsync (33.8 kHz)
(II) intel(0): Modeline "800x600"x0.0 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz)
(II) intel(0): Modeline "640x480"x0.0 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz)
(II) intel(0): Modeline "1024x768"x0.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz)
(II) intel(0): Modeline "1280x1024"x0.0 108.00 1280 1328 1440 1688 1024 1025 1028 1066 +hsync +vsync (64.0 kHz)
(II) intel(0): Modeline "1600x1200"x0.0 162.00 1600 1664 1856 2160 1200 1201 1204 1250 +hsync +vsync (75.0 kHz)
(II) intel(0): EDID vendor "MJI", prod id 17
(II) intel(0): Printing probed modes for output HDMI-1
(II) intel(0): Modeline "1920x1080"x60.0 148.50 1920 2008 2052 2200 1080 1084 1089 1125 +hsync +vsync (67.5 kHz)
(II) intel(0): Modeline "1600x1200"x60.0 162.00 1600 1664 1856 2160 1200 1201 1204 1250 +hsync +vsync (75.0 kHz)
(II) intel(0): Modeline "1280x1024"x60.0 108.00 1280 1328 1440 1688 1024 1025 1028 1066 +hsync +vsync (64.0 kHz)
(II) intel(0): Modeline "1920x540"x120.1 74.25 1920 2008 2052 2200 540 542 547 562 interlace +hsync +vsync (33.8 kHz)
(II) intel(0): Modeline "1024x768"x60.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz)
(II) intel(0): Modeline "800x600"x60.3 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz)
(II) intel(0): Modeline "640x480"x59.9 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz)
(II) intel(0): EDID for output HDMI-2
More information about the Intel-gfx
mailing list