[Intel-gfx] Black screen on boot with next-0517
Cedric Sodhi
manday at gmx.net
Wed May 18 15:16:24 CEST 2011
I'm troubled by a regression that must have occurred somewhere between
next-05-11 and next-05-17, that is, the screen blacks out (backlight is
still lit and can be regulated) on boot.
i915.modeset=0
Will cause the console to visually freeze instead.
This is a SWITCHEROO setup with a Radeon, but I blame intel for that.
Dmesg attached. Blackout occurs at arround 1.3559. After that, when the
backlight is brought back up, the screen is empty/black but lit.
(Not to mention, backlight goes back to 0 and has to be brought up, as
it always has been - see bug report)
regards,
MD
-------------- next part --------------
[ 0.000000] Linux version 2.6.39-rc7-next-20110517 (root at fly) (gcc version 4.4.5 (Gentoo 4.4.5 p1.2, pie-0.4.5) ) #1 SMP Wed May 18 13:16:36 CEST 2011
[ 0.000000] Command line: auto BOOT_IMAGE=Default ro root=801
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009d000 (usable)
[ 0.000000] BIOS-e820: 000000000009d000 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000009b63f000 (usable)
[ 0.000000] BIOS-e820: 000000009b63f000 - 000000009b6bf000 (reserved)
[ 0.000000] BIOS-e820: 000000009b6bf000 - 000000009b7bf000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000009b7bf000 - 000000009b7ff000 (ACPI data)
[ 0.000000] BIOS-e820: 000000009b7ff000 - 000000009b800000 (usable)
[ 0.000000] BIOS-e820: 000000009b800000 - 00000000a0000000 (reserved)
[ 0.000000] BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
[ 0.000000] BIOS-e820: 00000000feb00000 - 00000000feb04000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
[ 0.000000] BIOS-e820: 00000000fed10000 - 00000000fed14000 (reserved)
[ 0.000000] BIOS-e820: 00000000fed18000 - 00000000fed1a000 (reserved)
[ 0.000000] BIOS-e820: 00000000fed1c000 - 00000000fed20000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] BIOS-e820: 00000000ffe00000 - 0000000100000000 (reserved)
[ 0.000000] BIOS-e820: 0000000100000000 - 0000000158000000 (usable)
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] DMI 2.6 present.
[ 0.000000] DMI: Hewlett-Packard HP TouchSmart tm2 Notebook PC /1486, BIOS F.23 10/28/2010
[ 0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
[ 0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
[ 0.000000] No AGP bridge found
[ 0.000000] last_pfn = 0x158000 max_arch_pfn = 0x400000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-EFFFF write-through
[ 0.000000] F0000-FFFFF write-combining
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 000000000 mask F80000000 write-back
[ 0.000000] 1 base 0FFE00000 mask FFFE00000 write-protect
[ 0.000000] 2 base 080000000 mask FE0000000 write-back
[ 0.000000] 3 base 09C000000 mask FFC000000 uncachable
[ 0.000000] 4 base 09B800000 mask FFF800000 uncachable
[ 0.000000] 5 base 100000000 mask F80000000 write-back
[ 0.000000] 6 base 158000000 mask FF8000000 uncachable
[ 0.000000] 7 base 160000000 mask FE0000000 uncachable
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] last_pfn = 0x9b800 max_arch_pfn = 0x400000000
[ 0.000000] initial memory mapped : 0 - 20000000
[ 0.000000] Base memory trampoline at [ffff880000098000] 98000 size 20480
[ 0.000000] init_memory_mapping: 0000000000000000-000000009b800000
[ 0.000000] 0000000000 - 009b800000 page 2M
[ 0.000000] kernel direct mapping tables up to 9b800000 @ 9b63b000-9b63f000
[ 0.000000] init_memory_mapping: 0000000100000000-0000000158000000
[ 0.000000] 0100000000 - 0158000000 page 2M
[ 0.000000] kernel direct mapping tables up to 158000000 @ 157ff9000-158000000
[ 0.000000] ACPI: RSDP 00000000000fe020 00024 (v02 HP )
[ 0.000000] ACPI: XSDT 000000009b7fe120 00094 (v01 HPQOEM SLIC-MPC 00000001 01000013)
[ 0.000000] ACPI: FACP 000000009b7fc000 000F4 (v04 HP SLIC-MPC 00000001 MSFT 01000013)
[ 0.000000] ACPI: DSDT 000000009b7e9000 0FCE7 (v02 HP SLIC-MPC 00000001 MSFT 01000013)
[ 0.000000] ACPI: FACS 000000009b75e000 00040
[ 0.000000] ACPI: ASF! 000000009b7fd000 000A5 (v32 HP SLIC-MPC 00000001 MSFT 01000013)
[ 0.000000] ACPI: HPET 000000009b7fb000 00038 (v01 HP SLIC-MPC 00000001 MSFT 01000013)
[ 0.000000] ACPI: APIC 000000009b7fa000 0008C (v02 HP SLIC-MPC 00000001 MSFT 01000013)
[ 0.000000] ACPI: MCFG 000000009b7f9000 0003C (v01 HP SLIC-MPC 00000001 MSFT 01000013)
[ 0.000000] ACPI: SLIC 000000009b7e8000 00176 (v01 HPQOEM SLIC-MPC 00000001 MSFT 01000013)
[ 0.000000] ACPI: SSDT 000000009b7e6000 01152 (v01 TrmRef PtidDevc 00001000 INTL 20051117)
[ 0.000000] ACPI: SSDT 000000009b7e5000 00172 (v01 VaRef Va_Acpi 00003000 INTL 20051117)
[ 0.000000] ACPI: BOOT 000000009b7e4000 00028 (v01 HP SLIC-MPC 00000001 MSFT 01000013)
[ 0.000000] ACPI: SSDT 000000009b7e3000 00C39 (v01 INTEL SataPri 00001000 INTL 20051117)
[ 0.000000] ACPI: SSDT 000000009b7e2000 006C5 (v01 INTEL SataSec 00001000 INTL 20051117)
[ 0.000000] ACPI: ASPT 000000009b7e1000 00034 (v04 HP SLIC-MPC 00000001 MSFT 01000013)
[ 0.000000] ACPI: SSDT 000000009b7e0000 009F1 (v01 PmRef CpuPm 00003000 INTL 20051117)
[ 0.000000] ACPI: SSDT 000000009b7de000 01A8F (v01 AmdRef AmdTabl 00001000 INTL 20051117)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] [ffffea0000000000-ffffea0004bfffff] PMD -> [ffff880153800000-ffff880156ffffff] on node 0
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000010 -> 0x00001000
[ 0.000000] DMA32 0x00001000 -> 0x00100000
[ 0.000000] Normal 0x00100000 -> 0x00158000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[4] active PFN ranges
[ 0.000000] 0: 0x00000010 -> 0x0000009d
[ 0.000000] 0: 0x00000100 -> 0x0009b63f
[ 0.000000] 0: 0x0009b7ff -> 0x0009b800
[ 0.000000] 0: 0x00100000 -> 0x00158000
[ 0.000000] On node 0 totalpages: 996813
[ 0.000000] DMA zone: 56 pages used for memmap
[ 0.000000] DMA zone: 5 pages reserved
[ 0.000000] DMA zone: 3920 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 14280 pages used for memmap
[ 0.000000] DMA32 zone: 618104 pages, LIFO batch:31
[ 0.000000] Normal zone: 4928 pages used for memmap
[ 0.000000] Normal zone: 355520 pages, LIFO batch:31
[ 0.000000] ACPI: PM-Timer IO Port: 0x408
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x04] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x05] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x00] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x06] lapic_id[0x00] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x07] lapic_id[0x00] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x08] lapic_id[0x00] disabled)
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[ 0.000000] 8 Processors exceeds NR_CPUS limit of 4
[ 0.000000] SMP: Allowing 4 CPUs, 0 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 40
[ 0.000000] PM: Registered nosave memory: 000000000009d000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
[ 0.000000] PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
[ 0.000000] PM: Registered nosave memory: 000000009b63f000 - 000000009b6bf000
[ 0.000000] PM: Registered nosave memory: 000000009b6bf000 - 000000009b7bf000
[ 0.000000] PM: Registered nosave memory: 000000009b7bf000 - 000000009b7ff000
[ 0.000000] PM: Registered nosave memory: 000000009b800000 - 00000000a0000000
[ 0.000000] PM: Registered nosave memory: 00000000a0000000 - 00000000e0000000
[ 0.000000] PM: Registered nosave memory: 00000000e0000000 - 00000000f0000000
[ 0.000000] PM: Registered nosave memory: 00000000f0000000 - 00000000feb00000
[ 0.000000] PM: Registered nosave memory: 00000000feb00000 - 00000000feb04000
[ 0.000000] PM: Registered nosave memory: 00000000feb04000 - 00000000fec00000
[ 0.000000] PM: Registered nosave memory: 00000000fec00000 - 00000000fec01000
[ 0.000000] PM: Registered nosave memory: 00000000fec01000 - 00000000fed10000
[ 0.000000] PM: Registered nosave memory: 00000000fed10000 - 00000000fed14000
[ 0.000000] PM: Registered nosave memory: 00000000fed14000 - 00000000fed18000
[ 0.000000] PM: Registered nosave memory: 00000000fed18000 - 00000000fed1a000
[ 0.000000] PM: Registered nosave memory: 00000000fed1a000 - 00000000fed1c000
[ 0.000000] PM: Registered nosave memory: 00000000fed1c000 - 00000000fed20000
[ 0.000000] PM: Registered nosave memory: 00000000fed20000 - 00000000fee00000
[ 0.000000] PM: Registered nosave memory: 00000000fee00000 - 00000000fee01000
[ 0.000000] PM: Registered nosave memory: 00000000fee01000 - 00000000ffe00000
[ 0.000000] PM: Registered nosave memory: 00000000ffe00000 - 0000000100000000
[ 0.000000] Allocating PCI resources starting at a0000000 (gap: a0000000:40000000)
[ 0.000000] setup_percpu: NR_CPUS:4 nr_cpumask_bits:4 nr_cpu_ids:4 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 26 pages/cpu @ffff880157c00000 s74048 r8192 d24256 u524288
[ 0.000000] pcpu-alloc: s74048 r8192 d24256 u524288 alloc=1*2097152
[ 0.000000] pcpu-alloc: [0] 0 1 2 3
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 977544
[ 0.000000] Kernel command line: auto BOOT_IMAGE=Default ro root=801
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
[ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.000000] Checking aperture...
[ 0.000000] No AGP bridge found
[ 0.000000] Memory: 3848808k/5636096k available (4807k kernel code, 1648844k absent, 138444k reserved, 2573k data, 448k init)
[ 0.000000] SLUB: Genslabs=15, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] CONFIG_RCU_FANOUT set to non-default value of 32
[ 0.000000] NR_IRQS:384
[ 0.000000] Extended CMOS year: 2000
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] hpet clockevent registered
[ 0.000000] Fast TSC calibration using PIT
[ 0.004000] Detected 1197.193 MHz processor.
[ 0.000004] Calibrating delay loop (skipped), value calculated using timer frequency.. 2394.38 BogoMIPS (lpj=4788772)
[ 0.000169] pid_max: default: 32768 minimum: 301
[ 0.000324] Mount-cache hash table entries: 256
[ 0.000608] CPU: Physical Processor ID: 0
[ 0.000686] CPU: Processor Core ID: 0
[ 0.000767] mce: CPU supports 9 MCE banks
[ 0.000855] CPU0: Thermal monitoring handled by SMI
[ 0.000865] using mwait in idle threads.
[ 0.001038] ACPI: Core revision 20110316
[ 0.034749] Setting APIC routing to flat
[ 0.035179] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.074932] CPU0: Intel(R) Core(TM) i5 CPU U 430 @ 1.20GHz stepping 05
[ 0.179476] Performance Events: PEBS fmt1+, Westmere events, Intel PMU driver.
[ 0.179713] ... version: 3
[ 0.179790] ... bit width: 48
[ 0.179868] ... generic registers: 4
[ 0.179946] ... value mask: 0000ffffffffffff
[ 0.180029] ... max period: 000000007fffffff
[ 0.180111] ... fixed-purpose events: 3
[ 0.180189] ... event mask: 000000070000000f
[ 0.180458] Booting Node 0, Processors #1
[ 0.180554] smpboot cpu 1: start_ip = 98000
[ 0.271451] CPU1: Thermal monitoring handled by SMI
[ 0.291594] #2
[ 0.291643] smpboot cpu 2: start_ip = 98000
[ 0.379387] CPU2: Thermal monitoring handled by SMI
[ 0.399597] #3 Ok.
[ 0.399671] smpboot cpu 3: start_ip = 98000
[ 0.487323] CPU3: Thermal monitoring handled by SMI
[ 0.507377] Brought up 4 CPUs
[ 0.507456] Total of 4 processors activated (9576.25 BogoMIPS).
[ 0.509676] PM: Registering ACPI NVS region at 9b6bf000 (1048576 bytes)
[ 0.509970] print_constraints: dummy:
[ 0.510099] NET: Registered protocol family 16
[ 0.510527] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
[ 0.510641] ACPI: bus type pci registered
[ 0.510847] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[ 0.510968] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in E820
[ 0.553097] PCI: Using configuration type 1 for base access
[ 0.560511] bio: create slab <bio-0> at 0
[ 0.563686] ACPI: EC: Look up EC in DSDT
[ 0.566523] ACPI: Executed 1 blocks of module-level executable AML code
[ 0.599421] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored
[ 0.606031] ACPI: SSDT 000000009b691a98 00334 (v01 PmRef Cpu0Ist 00003000 INTL 20051117)
[ 0.606938] ACPI: Dynamic OEM Table Load:
[ 0.607096] ACPI: SSDT (null) 00334 (v01 PmRef Cpu0Ist 00003000 INTL 20051117)
[ 0.610340] ACPI: SSDT 000000009b690018 00891 (v01 PmRef Cpu0Cst 00003001 INTL 20051117)
[ 0.611212] ACPI: Dynamic OEM Table Load:
[ 0.611380] ACPI: SSDT (null) 00891 (v01 PmRef Cpu0Cst 00003001 INTL 20051117)
[ 0.635803] ACPI: SSDT 000000009b691718 00303 (v01 PmRef ApIst 00003000 INTL 20051117)
[ 0.636779] ACPI: Dynamic OEM Table Load:
[ 0.636938] ACPI: SSDT (null) 00303 (v01 PmRef ApIst 00003000 INTL 20051117)
[ 0.655477] ACPI: SSDT 000000009b68fd98 00119 (v01 PmRef ApCst 00003000 INTL 20051117)
[ 0.656394] ACPI: Dynamic OEM Table Load:
[ 0.656553] ACPI: SSDT (null) 00119 (v01 PmRef ApCst 00003000 INTL 20051117)
[ 1.079219] ACPI: Interpreter enabled
[ 1.079300] ACPI: (supports S0 S3 S4 S5)
[ 1.079598] ACPI: Using IOAPIC for interrupt routing
[ 1.081497] [Firmware Bug]: ACPI: No _BQC method, cannot determine initial brightness
[ 1.098141] [Firmware Bug]: ACPI: No _BQC method, cannot determine initial brightness
[ 1.101776] ACPI: Power Resource [FN00] (on)
[ 1.102618] ACPI: EC: GPE = 0x17, I/O: command/status = 0x66, data = 0x62
[ 1.102784] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[ 1.103515] \_SB_.PCI0:_OSC invalid UUID
[ 1.103518] _OSC request data:1 8 1f
[ 1.103523] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-fe])
[ 1.104621] pci_root PNP0A08:00: host bridge window [io 0x0000-0x0cf7]
[ 1.104710] pci_root PNP0A08:00: host bridge window [io 0x0d00-0xffff]
[ 1.104798] pci_root PNP0A08:00: host bridge window [mem 0x000a0000-0x000bffff]
[ 1.104912] pci_root PNP0A08:00: host bridge window [mem 0xa0000000-0xfeafffff]
[ 1.105040] pci 0000:00:00.0: [8086:0044] type 0 class 0x000600
[ 1.105090] pci 0000:00:01.0: [8086:0045] type 1 class 0x000604
[ 1.105128] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[ 1.105133] pci 0000:00:01.0: PME# disabled
[ 1.105152] pci 0000:00:02.0: [8086:0046] type 0 class 0x000300
[ 1.105169] pci 0000:00:02.0: reg 10: [mem 0xc0000000-0xc03fffff 64bit]
[ 1.105178] pci 0000:00:02.0: reg 18: [mem 0xb0000000-0xbfffffff 64bit pref]
[ 1.105186] pci 0000:00:02.0: reg 20: [io 0x4050-0x4057]
[ 1.105258] pci 0000:00:16.0: [8086:3b64] type 0 class 0x000780
[ 1.105289] pci 0000:00:16.0: reg 10: [mem 0xc4506100-0xc450610f 64bit]
[ 1.105365] pci 0000:00:16.0: PME# supported from D0 D3hot D3cold
[ 1.105370] pci 0000:00:16.0: PME# disabled
[ 1.105411] pci 0000:00:1a.0: [8086:3b3c] type 0 class 0x000c03
[ 1.105720] pci 0000:00:1a.0: reg 10: [mem 0xc4505c00-0xc4505fff]
[ 1.107400] pci 0000:00:1a.0: PME# supported from D0 D3hot D3cold
[ 1.107406] pci 0000:00:1a.0: PME# disabled
[ 1.107438] pci 0000:00:1b.0: [8086:3b56] type 0 class 0x000403
[ 1.107457] pci 0000:00:1b.0: reg 10: [mem 0xc4500000-0xc4503fff 64bit]
[ 1.107521] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[ 1.107526] pci 0000:00:1b.0: PME# disabled
[ 1.107549] pci 0000:00:1c.0: [8086:3b42] type 1 class 0x000604
[ 1.107613] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[ 1.107618] pci 0000:00:1c.0: PME# disabled
[ 1.107642] pci 0000:00:1c.1: [8086:3b44] type 1 class 0x000604
[ 1.107707] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
[ 1.107711] pci 0000:00:1c.1: PME# disabled
[ 1.107750] pci 0000:00:1d.0: [8086:3b34] type 0 class 0x000c03
[ 1.108038] pci 0000:00:1d.0: reg 10: [mem 0xc4505800-0xc4505bff]
[ 1.109717] pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold
[ 1.109722] pci 0000:00:1d.0: PME# disabled
[ 1.109746] pci 0000:00:1e.0: [8086:2448] type 1 class 0x000604
[ 1.109815] pci 0000:00:1f.0: [8086:3b09] type 0 class 0x000601
[ 1.109946] pci 0000:00:1f.2: [8086:3b29] type 0 class 0x000106
[ 1.109974] pci 0000:00:1f.2: reg 10: [io 0x4048-0x404f]
[ 1.109987] pci 0000:00:1f.2: reg 14: [io 0x405c-0x405f]
[ 1.109998] pci 0000:00:1f.2: reg 18: [io 0x4040-0x4047]
[ 1.110011] pci 0000:00:1f.2: reg 1c: [io 0x4058-0x405b]
[ 1.110023] pci 0000:00:1f.2: reg 20: [io 0x4020-0x403f]
[ 1.110035] pci 0000:00:1f.2: reg 24: [mem 0xc4505000-0xc45057ff]
[ 1.110085] pci 0000:00:1f.2: PME# supported from D3hot
[ 1.110090] pci 0000:00:1f.2: PME# disabled
[ 1.110114] pci 0000:00:1f.3: [8086:3b30] type 0 class 0x000c05
[ 1.110132] pci 0000:00:1f.3: reg 10: [mem 0xc4506000-0xc45060ff 64bit]
[ 1.110157] pci 0000:00:1f.3: reg 20: [io 0x4000-0x401f]
[ 1.110201] pci 0000:00:1f.6: [8086:3b32] type 0 class 0x001180
[ 1.110228] pci 0000:00:1f.6: reg 10: [mem 0xc4504000-0xc4504fff 64bit]
[ 1.110350] pci 0000:01:00.0: [1002:68e0] type 0 class 0x000300
[ 1.110373] pci 0000:01:00.0: reg 10: [mem 0xa0000000-0xafffffff 64bit pref]
[ 1.110391] pci 0000:01:00.0: reg 18: [mem 0xc4400000-0xc441ffff 64bit]
[ 1.110404] pci 0000:01:00.0: reg 20: [io 0x3000-0x30ff]
[ 1.110426] pci 0000:01:00.0: reg 30: [mem 0xfffe0000-0xffffffff pref]
[ 1.110456] pci 0000:01:00.0: supports D1 D2
[ 1.110486] pci 0000:01:00.1: [1002:aa68] type 0 class 0x000403
[ 1.110508] pci 0000:01:00.1: reg 10: [mem 0xc4420000-0xc4423fff 64bit]
[ 1.110584] pci 0000:01:00.1: supports D1 D2
[ 1.110617] pci 0000:00:01.0: PCI bridge to [bus 01-01]
[ 1.110702] pci 0000:00:01.0: bridge window [io 0x3000-0x3fff]
[ 1.110706] pci 0000:00:01.0: bridge window [mem 0xc4400000-0xc44fffff]
[ 1.110711] pci 0000:00:01.0: bridge window [mem 0xa0000000-0xafffffff 64bit pref]
[ 1.110780] pci 0000:02:00.0: [10ec:8168] type 0 class 0x000200
[ 1.110800] pci 0000:02:00.0: reg 10: [io 0x2000-0x20ff]
[ 1.110831] pci 0000:02:00.0: reg 18: [mem 0xc0404000-0xc0404fff 64bit pref]
[ 1.110852] pci 0000:02:00.0: reg 20: [mem 0xc0400000-0xc0403fff 64bit pref]
[ 1.110909] pci 0000:02:00.0: supports D1 D2
[ 1.110912] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 1.110919] pci 0000:02:00.0: PME# disabled
[ 1.110961] pci 0000:00:1c.0: PCI bridge to [bus 02-02]
[ 1.111050] pci 0000:00:1c.0: bridge window [io 0x2000-0x2fff]
[ 1.111056] pci 0000:00:1c.0: bridge window [mem 0xc3400000-0xc43fffff]
[ 1.111063] pci 0000:00:1c.0: bridge window [mem 0xc0400000-0xc13fffff 64bit pref]
[ 1.111166] pci 0000:03:00.0: [14e4:4727] type 0 class 0x000280
[ 1.111194] pci 0000:03:00.0: reg 10: [mem 0xc2400000-0xc2403fff 64bit]
[ 1.111301] pci 0000:03:00.0: supports D1 D2
[ 1.111340] pci 0000:00:1c.1: PCI bridge to [bus 03-03]
[ 1.111425] pci 0000:00:1c.1: bridge window [io 0x1000-0x1fff]
[ 1.111430] pci 0000:00:1c.1: bridge window [mem 0xc2400000-0xc33fffff]
[ 1.111438] pci 0000:00:1c.1: bridge window [mem 0xc1400000-0xc23fffff 64bit pref]
[ 1.111507] pci 0000:00:1e.0: PCI bridge to [bus 04-04] (subtractive decode)
[ 1.111599] pci 0000:00:1e.0: bridge window [io 0xf000-0x0000] (disabled)
[ 1.111605] pci 0000:00:1e.0: bridge window [mem 0xfff00000-0x000fffff] (disabled)
[ 1.111613] pci 0000:00:1e.0: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
[ 1.111617] pci 0000:00:1e.0: bridge window [io 0x0000-0x0cf7] (subtractive decode)
[ 1.111620] pci 0000:00:1e.0: bridge window [io 0x0d00-0xffff] (subtractive decode)
[ 1.111624] pci 0000:00:1e.0: bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
[ 1.111627] pci 0000:00:1e.0: bridge window [mem 0xa0000000-0xfeafffff] (subtractive decode)
[ 1.111648] pci_bus 0000:00: on NUMA node 0
[ 1.111653] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 1.111940] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P2._PRT]
[ 1.112004] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
[ 1.112134] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
[ 1.112199] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02._PRT]
[ 1.112351] \_SB_.PCI0:_OSC invalid UUID
[ 1.112353] _OSC request data:1 f 1f
[ 1.112358] pci0000:00: Unable to request _OSC control (_OSC support mask: 0x0f)
[ 1.121562] ACPI: PCI Root Bridge [CPBG] (domain 0000 [bus ff])
[ 1.121756] pci 0000:ff:00.0: [8086:2c62] type 0 class 0x000600
[ 1.121785] pci 0000:ff:00.1: [8086:2d01] type 0 class 0x000600
[ 1.121814] pci 0000:ff:02.0: [8086:2d10] type 0 class 0x000600
[ 1.121839] pci 0000:ff:02.1: [8086:2d11] type 0 class 0x000600
[ 1.121864] pci 0000:ff:02.2: [8086:2d12] type 0 class 0x000600
[ 1.121889] pci 0000:ff:02.3: [8086:2d13] type 0 class 0x000600
[ 1.121927] pci_bus 0000:ff: on NUMA node 0
[ 1.121937] pci0000:ff: Unable to request _OSC control (_OSC support mask: 0x0f)
[ 1.122504] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 *5 6 7 10 12 14 15)
[ 1.123145] ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 11 12 14 15) *10
[ 1.123831] ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 *10 12 14 15)
[ 1.124451] ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 *5 6 7 11 12 14 15)
[ 1.125074] ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
[ 1.125760] ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 11 12 14 15) *0, disabled.
[ 1.126489] ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
[ 1.127190] ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 5 6 7 11 12 14 15) *0, disabled.
[ 1.128027] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
[ 1.128152] vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=none,locks=none
[ 1.128271] vgaarb: loaded
[ 1.128344] vgaarb: bridge control possible 0000:01:00.0
[ 1.128426] vgaarb: bridge control possible 0000:00:02.0
[ 1.128670] SCSI subsystem initialized
[ 1.128828] libata version 3.00 loaded.
[ 1.128905] usbcore: registered new interface driver usbfs
[ 1.129023] usbcore: registered new interface driver hub
[ 1.129149] usbcore: registered new device driver usb
[ 1.130012] wmi: Mapper loaded
[ 1.130128] Advanced Linux Sound Architecture Driver Version 1.0.24.
[ 1.130215] PCI: Using ACPI for IRQ routing
[ 1.130295] PCI: pci_cache_line_size set to 64 bytes
[ 1.130385] reserve RAM buffer: 000000000009d000 - 000000000009ffff
[ 1.130389] reserve RAM buffer: 000000009b63f000 - 000000009bffffff
[ 1.130392] reserve RAM buffer: 000000009b800000 - 000000009bffffff
[ 1.130714] cfg80211: Calling CRDA to update world regulatory domain
[ 1.131051] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0, 0, 0, 0, 0
[ 1.131498] hpet0: 8 comparators, 64-bit 14.318180 MHz counter
[ 1.133602] Switching to clocksource hpet
[ 1.133766] pnp: PnP ACPI init
[ 1.133849] ACPI: bus type pnp registered
[ 1.134427] pnp 00:00: [bus 00-fe]
[ 1.134431] pnp 00:00: [io 0x0000-0x0cf7 window]
[ 1.134434] pnp 00:00: [io 0x0cf8-0x0cff]
[ 1.134436] pnp 00:00: [io 0x0d00-0xffff window]
[ 1.134440] pnp 00:00: [mem 0x000a0000-0x000bffff window]
[ 1.134442] pnp 00:00: [mem 0x000c0000-0x000c3fff window]
[ 1.134445] pnp 00:00: [mem 0x000c4000-0x000c7fff window]
[ 1.134448] pnp 00:00: [mem 0x000c8000-0x000cbfff window]
[ 1.134451] pnp 00:00: [mem 0x000cc000-0x000cffff window]
[ 1.134454] pnp 00:00: [mem 0x000d0000-0x000d3fff window]
[ 1.134456] pnp 00:00: [mem 0x000d4000-0x000d7fff window]
[ 1.134459] pnp 00:00: [mem 0x000d8000-0x000dbfff window]
[ 1.134462] pnp 00:00: [mem 0x000dc000-0x000dffff window]
[ 1.134465] pnp 00:00: [mem 0x000e0000-0x000e3fff window]
[ 1.134468] pnp 00:00: [mem 0x000e4000-0x000e7fff window]
[ 1.134470] pnp 00:00: [mem 0x000e8000-0x000ebfff window]
[ 1.134475] pnp 00:00: [mem 0x000ec000-0x000effff window]
[ 1.134478] pnp 00:00: [mem 0x000f0000-0x000fffff window]
[ 1.134481] pnp 00:00: [mem 0xa0000000-0xfeafffff window]
[ 1.134484] pnp 00:00: [mem 0xfed40000-0xfed44fff window]
[ 1.134597] pnp 00:00: Plug and Play ACPI device, IDs PNP0a08 PNP0a03 (active)
[ 1.134693] pnp 00:01: [io 0x0000-0x001f]
[ 1.134696] pnp 00:01: [io 0x0081-0x0091]
[ 1.134698] pnp 00:01: [io 0x0093-0x009f]
[ 1.134701] pnp 00:01: [io 0x00c0-0x00df]
[ 1.134704] pnp 00:01: [dma 4]
[ 1.134767] pnp 00:01: Plug and Play ACPI device, IDs PNP0200 (active)
[ 1.134780] pnp 00:02: [mem 0xff000000-0xffffffff]
[ 1.134838] pnp 00:02: Plug and Play ACPI device, IDs INT0800 (active)
[ 1.134932] Switched to NOHz mode on CPU #0
[ 1.135013] Switched to NOHz mode on CPU #3
[ 1.135019] Switched to NOHz mode on CPU #1
[ 1.135083] Switched to NOHz mode on CPU #2
[ 1.135338] pnp 00:03: [mem 0xfed00000-0xfed003ff]
[ 1.135411] pnp 00:03: Plug and Play ACPI device, IDs PNP0103 (active)
[ 1.135427] pnp 00:04: [io 0x00f0]
[ 1.135437] pnp 00:04: [irq 13]
[ 1.135505] pnp 00:04: Plug and Play ACPI device, IDs PNP0c04 (active)
[ 1.135522] pnp 00:05: [io 0x002e-0x002f]
[ 1.135524] pnp 00:05: [io 0x004e-0x004f]
[ 1.135527] pnp 00:05: [io 0x0061]
[ 1.135529] pnp 00:05: [io 0x0063]
[ 1.135531] pnp 00:05: [io 0x0065]
[ 1.135533] pnp 00:05: [io 0x0067]
[ 1.135536] pnp 00:05: [io 0x0070]
[ 1.135538] pnp 00:05: [io 0x0080]
[ 1.135540] pnp 00:05: [io 0x0092]
[ 1.135542] pnp 00:05: [io 0x00b2-0x00b3]
[ 1.135545] pnp 00:05: [io 0x0680-0x069f]
[ 1.135547] pnp 00:05: [io 0x0800-0x080f]
[ 1.135550] pnp 00:05: [io 0x0810-0x0813]
[ 1.135552] pnp 00:05: [io 0xffff]
[ 1.135554] pnp 00:05: [io 0x0400-0x047f]
[ 1.135557] pnp 00:05: [io 0x0500-0x0501]
[ 1.135559] pnp 00:05: [io 0x0700-0x077f]
[ 1.135562] pnp 00:05: [io 0x164e-0x164f]
[ 1.135579] pnp 00:05: disabling [io 0x164e-0x164f] because it overlaps 0000:00:1c.1 BAR 7 [io 0x1000-0x1fff]
[ 1.135787] system 00:05: [io 0x0680-0x069f] has been reserved
[ 1.135873] system 00:05: [io 0x0800-0x080f] has been reserved
[ 1.135960] system 00:05: [io 0x0810-0x0813] has been reserved
[ 1.136046] system 00:05: [io 0xffff] has been reserved
[ 1.136130] system 00:05: [io 0x0400-0x047f] has been reserved
[ 1.136216] system 00:05: [io 0x0500-0x0501] has been reserved
[ 1.136301] system 00:05: [io 0x0700-0x077f] has been reserved
[ 1.136388] system 00:05: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 1.136401] pnp 00:06: [io 0x0070-0x0077]
[ 1.136409] pnp 00:06: [irq 8]
[ 1.136474] pnp 00:06: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 1.136489] pnp 00:07: [io 0x0060]
[ 1.136491] pnp 00:07: [io 0x0064]
[ 1.136498] pnp 00:07: [irq 1]
[ 1.136564] pnp 00:07: Plug and Play ACPI device, IDs PNP0303 (active)
[ 1.136581] pnp 00:08: [irq 12]
[ 1.136652] pnp 00:08: Plug and Play ACPI device, IDs SYN1e2d SYN1e00 SYN0002 PNP0f13 (active)
[ 1.136807] pnp 00:09: [irq 23]
[ 1.136896] pnp 00:09: Plug and Play ACPI device, IDs HPQ0004 (active)
[ 1.137174] pnp 00:0a: [mem 0xfed1c000-0xfed1ffff]
[ 1.137177] pnp 00:0a: [mem 0xfed10000-0xfed13fff]
[ 1.137180] pnp 00:0a: [mem 0xfed18000-0xfed18fff]
[ 1.137182] pnp 00:0a: [mem 0xfed19000-0xfed19fff]
[ 1.137187] pnp 00:0a: [mem 0xe0000000-0xefffffff]
[ 1.137190] pnp 00:0a: [mem 0xfed20000-0xfed3ffff]
[ 1.137193] pnp 00:0a: [mem 0xfed90000-0xfed8ffff disabled]
[ 1.137195] pnp 00:0a: [mem 0xfed45000-0xfed8ffff]
[ 1.137198] pnp 00:0a: [mem 0xff000000-0xffffffff]
[ 1.137201] pnp 00:0a: [mem 0xfee00000-0xfeefffff]
[ 1.137203] pnp 00:0a: [mem 0xc4600000-0xc4600fff]
[ 1.137327] system 00:0a: [mem 0xfed1c000-0xfed1ffff] has been reserved
[ 1.137417] system 00:0a: [mem 0xfed10000-0xfed13fff] has been reserved
[ 1.137504] system 00:0a: [mem 0xfed18000-0xfed18fff] has been reserved
[ 1.137592] system 00:0a: [mem 0xfed19000-0xfed19fff] has been reserved
[ 1.137696] system 00:0a: [mem 0xe0000000-0xefffffff] has been reserved
[ 1.137785] system 00:0a: [mem 0xfed20000-0xfed3ffff] has been reserved
[ 1.137873] system 00:0a: [mem 0xfed45000-0xfed8ffff] has been reserved
[ 1.137961] system 00:0a: [mem 0xff000000-0xffffffff] could not be reserved
[ 1.138051] system 00:0a: [mem 0xfee00000-0xfeefffff] could not be reserved
[ 1.138140] system 00:0a: [mem 0xc4600000-0xc4600fff] has been reserved
[ 1.138229] system 00:0a: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 1.138545] pnp 00:0b: [bus ff]
[ 1.138651] pnp 00:0b: Plug and Play ACPI device, IDs PNP0a03 (active)
[ 1.138690] pnp: PnP ACPI: found 12 devices
[ 1.138769] ACPI: ACPI bus type pnp unregistered
[ 1.147146] pci 0000:01:00.0: no compatible bridge window for [mem 0xfffe0000-0xffffffff pref]
[ 1.147305] pci 0000:01:00.0: BAR 6: assigned [mem 0xc4440000-0xc445ffff pref]
[ 1.147419] pci 0000:00:01.0: PCI bridge to [bus 01-01]
[ 1.147502] pci 0000:00:01.0: bridge window [io 0x3000-0x3fff]
[ 1.147590] pci 0000:00:01.0: bridge window [mem 0xc4400000-0xc44fffff]
[ 1.147679] pci 0000:00:01.0: bridge window [mem 0xa0000000-0xafffffff 64bit pref]
[ 1.147796] pci 0000:00:1c.0: PCI bridge to [bus 02-02]
[ 1.147879] pci 0000:00:1c.0: bridge window [io 0x2000-0x2fff]
[ 1.147969] pci 0000:00:1c.0: bridge window [mem 0xc3400000-0xc43fffff]
[ 1.148058] pci 0000:00:1c.0: bridge window [mem 0xc0400000-0xc13fffff 64bit pref]
[ 1.148178] pci 0000:00:1c.1: PCI bridge to [bus 03-03]
[ 1.148261] pci 0000:00:1c.1: bridge window [io 0x1000-0x1fff]
[ 1.148349] pci 0000:00:1c.1: bridge window [mem 0xc2400000-0xc33fffff]
[ 1.148440] pci 0000:00:1c.1: bridge window [mem 0xc1400000-0xc23fffff 64bit pref]
[ 1.148559] pci 0000:00:1e.0: PCI bridge to [bus 04-04]
[ 1.148642] pci 0000:00:1e.0: bridge window [io disabled]
[ 1.148729] pci 0000:00:1e.0: bridge window [mem disabled]
[ 1.148814] pci 0000:00:1e.0: bridge window [mem pref disabled]
[ 1.148915] pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 1.149005] pci 0000:00:01.0: setting latency timer to 64
[ 1.149016] pci 0000:00:1c.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 1.149107] pci 0000:00:1c.0: setting latency timer to 64
[ 1.149115] pci 0000:00:1c.1: PCI INT B -> GSI 16 (level, low) -> IRQ 16
[ 1.149205] pci 0000:00:1c.1: setting latency timer to 64
[ 1.149213] pci 0000:00:1e.0: setting latency timer to 64
[ 1.149219] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
[ 1.149222] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]
[ 1.149225] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[ 1.149228] pci_bus 0000:00: resource 7 [mem 0xa0000000-0xfeafffff]
[ 1.149232] pci_bus 0000:01: resource 0 [io 0x3000-0x3fff]
[ 1.149235] pci_bus 0000:01: resource 1 [mem 0xc4400000-0xc44fffff]
[ 1.149238] pci_bus 0000:01: resource 2 [mem 0xa0000000-0xafffffff 64bit pref]
[ 1.149241] pci_bus 0000:02: resource 0 [io 0x2000-0x2fff]
[ 1.149244] pci_bus 0000:02: resource 1 [mem 0xc3400000-0xc43fffff]
[ 1.149247] pci_bus 0000:02: resource 2 [mem 0xc0400000-0xc13fffff 64bit pref]
[ 1.149250] pci_bus 0000:03: resource 0 [io 0x1000-0x1fff]
[ 1.149253] pci_bus 0000:03: resource 1 [mem 0xc2400000-0xc33fffff]
[ 1.149256] pci_bus 0000:03: resource 2 [mem 0xc1400000-0xc23fffff 64bit pref]
[ 1.149260] pci_bus 0000:04: resource 4 [io 0x0000-0x0cf7]
[ 1.149262] pci_bus 0000:04: resource 5 [io 0x0d00-0xffff]
[ 1.149265] pci_bus 0000:04: resource 6 [mem 0x000a0000-0x000bffff]
[ 1.149269] pci_bus 0000:04: resource 7 [mem 0xa0000000-0xfeafffff]
[ 1.149313] NET: Registered protocol family 2
[ 1.149436] IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 1.149872] TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
[ 1.151121] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 1.151487] TCP: Hash tables configured (established 262144 bind 65536)
[ 1.151575] TCP reno registered
[ 1.151653] UDP hash table entries: 2048 (order: 4, 65536 bytes)
[ 1.151759] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
[ 1.152005] NET: Registered protocol family 1
[ 1.152200] RPC: Registered udp transport module.
[ 1.152281] RPC: Registered tcp transport module.
[ 1.152361] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 1.152463] pci 0000:00:02.0: Boot video device
[ 1.152504] pci 0000:00:1a.0: EHCI: BIOS handoff
[ 1.165708] pci 0000:00:1d.0: EHCI: BIOS handoff
[ 1.181699] PCI: CLS 64 bytes, default 64
[ 1.181722] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[ 1.181810] Placing 64MB software IO TLB between ffff88009763b000 - ffff88009b63b000
[ 1.181924] software IO TLB at phys 0x9763b000 - 0x9b63b000
[ 1.182020] Simple Boot Flag at 0x44 set to 0x1
[ 1.227595] Installing knfsd (copyright (C) 1996 okir at monad.swb.de).
[ 1.227766] msgmni has been set to 7517
[ 1.230180] alg: No test for stdrng (krng)
[ 1.236852] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 1.236967] io scheduler noop registered
[ 1.237045] io scheduler deadline registered
[ 1.237204] io scheduler cfq registered (default)
[ 1.237406] pcieport 0000:00:01.0: setting latency timer to 64
[ 1.237713] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 1.237918] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 1.238053] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 1.238141] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[ 1.238843] intel_idle: MWAIT substates: 0x1120
[ 1.238845] intel_idle: v0.4 model 0x25
[ 1.238848] intel_idle: lapic_timer_reliable_states 0xffffffff
[ 1.337947] ACPI: AC Adapter [AC] (off-line)
[ 1.338436] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input0
[ 1.338585] ACPI: Lid Switch [LID0]
[ 1.338742] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1
[ 1.338862] ACPI: Power Button [PWRB]
[ 1.339021] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
[ 1.339136] ACPI: Power Button [PWRF]
[ 1.339344] ACPI: Fan [FAN0] (on)
[ 1.339462] ACPI: acpi_idle yielding to intel_idle
[ 1.347300] thermal LNXTHERM:00: registered as thermal_zone0
[ 1.347387] ACPI: Thermal Zone [TZ00] (45 C)
[ 1.348428] thermal LNXTHERM:01: registered as thermal_zone1
[ 1.348523] ACPI: Thermal Zone [TZ01] (36 C)
[ 1.349421] thermal LNXTHERM:02: registered as thermal_zone2
[ 1.349507] ACPI: Thermal Zone [TZ02] (56 C)
[ 1.351039] Linux agpgart interface v0.103
[ 1.351205] agpgart-intel 0000:00:00.0: Intel HD Graphics Chipset
[ 1.351481] agpgart-intel 0000:00:00.0: detected gtt size: 2097152K total, 262144K mappable
[ 1.352723] agpgart-intel 0000:00:00.0: detected 32768K stolen memory
[ 1.355905] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xb0000000
[ 1.356170] [drm] Initialized drm 1.1.0 20060810
[ 1.356300] [drm] radeon defaulting to kernel modesetting.
[ 1.356397] [drm] radeon kernel modesetting enabled.
[ 1.356537] VGA switcheroo: detected switching method \_SB_.PCI0.GFX0.ATPX handle
[ 1.356724] radeon 0000:01:00.0: enabling device (0000 -> 0003)
[ 1.356853] radeon 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 1.356980] radeon 0000:01:00.0: setting latency timer to 64
[ 1.357186] [drm] initializing kernel modesetting (CEDAR 0x1002:0x68E0).
[ 1.357316] [drm] register mmio base: 0xC4400000
[ 1.357398] [drm] register mmio size: 131072
[ 2.181089] Refined TSC clocksource calibration: 1196.999 MHz.
[ 2.181191] Switching to clocksource tsc
[ 7.227019] ACPI: Battery Slot [BAT0] (battery present)
[ 10.492599] ATOM BIOS: HP
[ 10.492747] radeon 0000:01:00.0: VRAM: 512M 0x0000000000000000 - 0x000000001FFFFFFF (512M used)
[ 10.492867] radeon 0000:01:00.0: GTT: 512M 0x0000000020000000 - 0x000000003FFFFFFF
[ 10.492987] mtrr: no more MTRRs available
[ 10.493064] [drm] Detected VRAM RAM=512M, BAR=256M
[ 10.493145] [drm] RAM width 64bits DDR
[ 10.493253] [TTM] Zone kernel: Available graphics memory: 1924404 kiB.
[ 10.493341] [TTM] Initializing pool allocator.
[ 10.493454] [drm] radeon: 512M of VRAM memory ready
[ 10.493536] [drm] radeon: 512M of GTT memory ready.
[ 10.493627] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[ 10.493745] [drm] Driver supports precise vblank timestamp query.
[ 10.493872] [drm] radeon: irq initialized.
[ 10.493955] [drm] GART: num cpu pages 131072, num gpu pages 131072
[ 10.494981] [drm] Loading CEDAR Microcode
[ 10.497545] radeon 0000:01:00.0: WB enabled
[ 10.514288] [drm] ring test succeeded in 1 usecs
[ 10.514468] [drm] radeon: ib pool ready.
[ 10.514681] [drm] ib test succeeded in 0 usecs
[ 10.515420] [drm] Radeon Display Connectors
[ 10.515499] [drm] Connector 0:
[ 10.515573] [drm] LVDS
[ 10.515646] [drm] DDC: 0x6560 0x6560 0x6564 0x6564 0x6568 0x6568 0x656c 0x656c
[ 10.515758] [drm] Encoders:
[ 10.515832] [drm] LCD1: INTERNAL_UNIPHY
[ 10.515911] [drm] Connector 1:
[ 10.515984] [drm] HDMI-A
[ 10.516057] [drm] HPD1
[ 10.516131] [drm] DDC: 0x6430 0x6430 0x6434 0x6434 0x6438 0x6438 0x643c 0x643c
[ 10.516244] [drm] Encoders:
[ 10.516318] [drm] DFP1: INTERNAL_UNIPHY1
[ 10.516396] [drm] Connector 2:
[ 10.516478] [drm] VGA
[ 10.516553] [drm] DDC: 0x64d8 0x64d8 0x64dc 0x64dc 0x64e0 0x64e0 0x64e4 0x64e4
[ 10.516666] [drm] Encoders:
[ 10.516740] [drm] CRT1: INTERNAL_KLDSCP_DAC1
[ 10.546667] [drm] Internal thermal controller with fan control
[ 10.546830] [drm] radeon: power management initialized
[ 10.578967] [drm] fb mappable at 0xA0141000
[ 10.579046] [drm] vram apper at 0xA0000000
[ 10.579124] [drm] size 4096000
[ 10.579198] [drm] fb depth is 24
[ 10.579273] [drm] pitch is 5120
[ 11.072575] Console: switching to colour frame buffer device 160x50
[ 11.076629] fb0: radeondrmfb frame buffer device
[ 11.076632] drm: registered panic notifier
[ 11.076644] [drm] Initialized radeon 2.9.0 20080528 for 0000:01:00.0 on minor 0
[ 11.076777] i915 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 11.076785] i915 0000:00:02.0: setting latency timer to 64
[ 11.131690] mtrr: no more MTRRs available
[ 11.131722] [drm] MTRR allocation failed. Graphics performance may suffer.
[ 11.132166] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[ 11.132210] [drm] Driver supports precise vblank timestamp query.
[ 11.132434] vga_switcheroo: enabled
[ 11.132513] radeon atpx: version is 1
[ 11.132563] vgaarb: device changed decodes: PCI:0000:01:00.0,olddecodes=io+mem,decodes=none:owns=none
[ 11.132627] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=none:owns=io+mem
[ 11.447824] fbcon: inteldrmfb (fb1) is primary device
[ 11.447870] fbcon: Remapping primary device, fb1, to tty 1-63
[ 12.129424] fb1: inteldrmfb frame buffer device
[ 12.130257] [Firmware Bug]: ACPI: No _BQC method, cannot determine initial brightness
[ 12.130977] acpi device:02: registered as cooling_device5
[ 12.131359] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:00/input/input3
[ 12.131427] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no)
[ 12.131499] [Firmware Bug]: ACPI(PEGP) defines _DOD but not _DOS
[ 12.133122] acpi device:0b: registered as cooling_device6
[ 12.133495] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:09/LNXVIDEO:01/input/input4
[ 12.133564] ACPI: Video Device [PEGP] (multi-head: yes rom: no post: no)
[ 12.133689] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 1
[ 12.135849] brd: module loaded
[ 12.138747] loop: module loaded
[ 12.140775] ahci 0000:00:1f.2: version 3.0
[ 12.140795] ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 12.142774] ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 4 ports 3 Gbps 0x1 impl SATA mode
[ 12.144787] ahci 0000:00:1f.2: flags: 64bit ncq sntf ilck pm led clo pio slum part ems apst
[ 12.146758] ahci 0000:00:1f.2: setting latency timer to 64
[ 12.147455] scsi0 : ahci
[ 12.149604] scsi1 : ahci
[ 12.151722] scsi2 : ahci
[ 12.153784] scsi3 : ahci
[ 12.155890] ata1: SATA max UDMA/133 abar m2048 at 0xc4505000 port 0xc4505100 irq 19
[ 12.157925] ata2: DUMMY
[ 12.159977] ata3: DUMMY
[ 12.162020] ata4: DUMMY
[ 12.164204] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 12.166217] ehci_hcd: block sizes: qh 104 qtd 96 itd 192 sitd 96
[ 12.166241] ehci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 12.168274] ehci_hcd 0000:00:1a.0: setting latency timer to 64
[ 12.168280] ehci_hcd 0000:00:1a.0: EHCI Host Controller
[ 12.170295] ehci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1
[ 12.172358] ehci_hcd 0000:00:1a.0: reset hcs_params 0x200003 dbg=2 cc=0 pcc=0 ordered !ppc ports=3
[ 12.172364] ehci_hcd 0000:00:1a.0: reset hcc_params 36881 caching frame 1024 64 bit addr
[ 12.172380] ehci_hcd 0000:00:1a.0: support lpm
[ 12.172393] ehci_hcd 0000:00:1a.0: debug port 2
[ 12.174438] ehci_hcd 0000:00:1a.0: reset command 0080012 (park)=0 ithresh=8 Periodic period=1024 Reset HALT
[ 12.178389] ehci_hcd 0000:00:1a.0: cache line size of 64 is not supported
[ 12.178392] ehci_hcd 0000:00:1a.0: supports USB remote wakeup
[ 12.178403] ehci_hcd 0000:00:1a.0: irq 16, io mem 0xc4505c00
[ 12.180448] ehci_hcd 0000:00:1a.0: reset command 0080002 (park)=0 ithresh=8 period=1024 Reset HALT
[ 12.184364] ehci_hcd 0000:00:1a.0: init command 0010001 (park)=0 ithresh=1 period=1024 RUN
[ 12.195549] ehci_hcd 0000:00:1a.0: USB 2.0 started, EHCI 1.00
[ 12.197638] usb usb1: default language 0x0409
[ 12.197646] usb usb1: udev 1, busnum 1, minor = 0
[ 12.197650] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 12.199703] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 12.201760] usb usb1: Product: EHCI Host Controller
[ 12.203828] usb usb1: Manufacturer: Linux 2.6.39-rc7-next-20110517 ehci_hcd
[ 12.205921] usb usb1: SerialNumber: 0000:00:1a.0
[ 12.208094] usb usb1: usb_probe_device
[ 12.208099] usb usb1: configuration #1 chosen from 1 choice
[ 12.208109] usb usb1: adding 1-0:1.0 (config #1, interface 0)
[ 12.208169] hub 1-0:1.0: usb_probe_interface
[ 12.208172] hub 1-0:1.0: usb_probe_interface - got id
[ 12.208176] hub 1-0:1.0: USB hub found
[ 12.210284] hub 1-0:1.0: 3 ports detected
[ 12.212428] hub 1-0:1.0: standalone hub
[ 12.212430] hub 1-0:1.0: no power switching (usb 1.0)
[ 12.212433] hub 1-0:1.0: individual port over-current protection
[ 12.212436] hub 1-0:1.0: power on to power good time: 20ms
[ 12.212441] hub 1-0:1.0: local power source is good
[ 12.212444] hub 1-0:1.0: trying to enable port power on non-switchable hub
[ 12.212521] ehci_hcd 0000:00:1d.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
[ 12.214652] ehci_hcd 0000:00:1d.0: setting latency timer to 64
[ 12.214656] ehci_hcd 0000:00:1d.0: EHCI Host Controller
[ 12.216764] ehci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
[ 12.218867] ehci_hcd 0000:00:1d.0: reset hcs_params 0x200003 dbg=2 cc=0 pcc=0 ordered !ppc ports=3
[ 12.218872] ehci_hcd 0000:00:1d.0: reset hcc_params 36881 caching frame 1024 64 bit addr
[ 12.218887] ehci_hcd 0000:00:1d.0: support lpm
[ 12.218899] ehci_hcd 0000:00:1d.0: debug port 2
[ 12.220988] ehci_hcd 0000:00:1d.0: reset command 0080012 (park)=0 ithresh=8 Periodic period=1024 Reset HALT
[ 12.224912] ehci_hcd 0000:00:1d.0: cache line size of 64 is not supported
[ 12.224915] ehci_hcd 0000:00:1d.0: supports USB remote wakeup
[ 12.224935] ehci_hcd 0000:00:1d.0: irq 20, io mem 0xc4505800
[ 12.227010] ehci_hcd 0000:00:1d.0: reset command 0080002 (park)=0 ithresh=8 period=1024 Reset HALT
[ 12.230952] ehci_hcd 0000:00:1d.0: init command 0010001 (park)=0 ithresh=1 period=1024 RUN
[ 12.239516] ehci_hcd 0000:00:1d.0: USB 2.0 started, EHCI 1.00
[ 12.241655] usb usb2: default language 0x0409
[ 12.241663] usb usb2: udev 1, busnum 2, minor = 128
[ 12.241666] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 12.243742] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 12.245825] usb usb2: Product: EHCI Host Controller
[ 12.245828] usb usb2: Manufacturer: Linux 2.6.39-rc7-next-20110517 ehci_hcd
[ 12.245831] usb usb2: SerialNumber: 0000:00:1d.0
[ 12.245934] usb usb2: usb_probe_device
[ 12.245938] usb usb2: configuration #1 chosen from 1 choice
[ 12.245946] usb usb2: adding 2-0:1.0 (config #1, interface 0)
[ 12.246002] hub 2-0:1.0: usb_probe_interface
[ 12.246005] hub 2-0:1.0: usb_probe_interface - got id
[ 12.246007] hub 2-0:1.0: USB hub found
[ 12.246012] hub 2-0:1.0: 3 ports detected
[ 12.246014] hub 2-0:1.0: standalone hub
[ 12.246016] hub 2-0:1.0: no power switching (usb 1.0)
[ 12.246018] hub 2-0:1.0: individual port over-current protection
[ 12.246021] hub 2-0:1.0: power on to power good time: 20ms
[ 12.246025] hub 2-0:1.0: local power source is good
[ 12.246027] hub 2-0:1.0: trying to enable port power on non-switchable hub
[ 12.246128] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 12.246130] ohci_hcd: block sizes: ed 80 td 96
[ 12.246176] uhci_hcd: USB Universal Host Controller Interface driver
[ 12.246281] usbcore: registered new interface driver usblp
[ 12.246284] Initializing USB Mass Storage driver...
[ 12.246334] usbcore: registered new interface driver usb-storage
[ 12.246336] USB Mass Storage support registered.
[ 12.246386] usbcore: registered new interface driver libusual
[ 12.246505] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 12.250870] i8042: Detected active multiplexing controller, rev 1.1
[ 12.253414] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 12.253421] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[ 12.253424] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[ 12.253427] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[ 12.253430] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[ 12.253616] mousedev: PS/2 mouse device common for all mice
[ 12.254041] rtc_cmos 00:06: RTC can wake from S4
[ 12.254189] rtc_cmos 00:06: rtc core: registered rtc_cmos as rtc0
[ 12.254221] rtc0: alarms up to one year, y3k, 242 bytes nvram, hpet irqs
[ 12.254261] i2c /dev entries driver
[ 12.255170] i801_smbus 0000:00:1f.3: PCI INT C -> GSI 19 (level, low) -> IRQ 19
[ 12.255430] lirc_dev: IR Remote Control driver registered, major 252
[ 12.255433] IR NEC protocol handler initialized
[ 12.255435] IR RC5(x) protocol handler initialized
[ 12.255436] IR RC6 protocol handler initialized
[ 12.255438] IR JVC protocol handler initialized
[ 12.255440] IR Sony protocol handler initialized
[ 12.255441] IR RC5 (streamzap) protocol handler initialized
[ 12.255443] IR LIRC bridge handler initialized
[ 12.255444] Linux video capture interface: v2.00
[ 12.255478] gspca: v2.12.0 registered
[ 12.271903] coretemp coretemp.0: TjMax is 105 C.
[ 12.272114] coretemp coretemp.2: TjMax is 105 C.
[ 12.272233] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.06
[ 12.272416] iTCO_wdt: Found a HM55 TCO device (Version=2, TCOBASE=0x0460)
[ 12.272505] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 12.272510] iTCO_vendor_support: vendor-support=0
[ 12.273162] cpuidle: using governor ladder
[ 12.326719] cpuidle: using governor menu
[ 12.326723] EFI Variables Facility v0.08 2004-May-17
[ 12.327456] usbcore: registered new interface driver usbhid
[ 12.327459] usbhid: USB HID core driver
[ 12.327533] hp_accel: laptop model unknown, using default axes configuration
[ 12.328312] lis3lv02d: 8 bits sensor found
[ 12.343510] ehci_hcd 0000:00:1d.0: GetStatus port:1 status 001803 0 ACK POWER sig=j CSC CONNECT
[ 12.343516] hub 2-0:1.0: port 1: status 0501 change 0001
[ 12.346963] ehci_hcd 0000:00:1a.0: GetStatus port:1 status 001803 0 ACK POWER sig=j CSC CONNECT
[ 12.346970] hub 1-0:1.0: port 1: status 0501 change 0001
[ 12.347140] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input5
[ 12.372018] input: ST LIS3LV02DL Accelerometer as /devices/platform/lis3lv02d/input/input6
[ 12.376443] Registered led device: hp::hddprotect
[ 12.376598] hp_accel: driver loaded
[ 12.443487] hub 2-0:1.0: state 7 ports 3 chg 0002 evt 0000
[ 12.443502] hub 2-0:1.0: port 1, status 0501, change 0000, 480 Mb/s
[ 12.483477] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 12.486113] ata1.00: ATA-8: Hitachi HTS725050A9A364, PC4OC72E, max UDMA/100
[ 12.487814] ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[ 12.490660] ata1.00: configured for UDMA/100
[ 12.494309] scsi 0:0:0:0: Direct-Access ATA Hitachi HTS72505 PC4O PQ: 0 ANSI: 5
[ 12.496883] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/465 GiB)
[ 12.500515] sd 0:0:0:0: [sda] Write Protect is off
[ 12.500589] ehci_hcd 0000:00:1d.0: port 1 high speed
[ 12.500598] ehci_hcd 0000:00:1d.0: GetStatus port:1 status 001005 0 ACK POWER sig=se0 PE CONNECT
[ 12.503834] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 12.503890] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 12.507527] sda: detected capacity change from 0 to 500107862016
[ 12.559388] usb 2-1: new high speed USB device number 2 using ehci_hcd
[ 12.615650] ehci_hcd 0000:00:1d.0: port 1 high speed
[ 12.615659] ehci_hcd 0000:00:1d.0: GetStatus port:1 status 001005 0 ACK POWER sig=se0 PE CONNECT
[ 12.691585] ehci_hcd 0000:00:1d.0: set dev address 2 for port 1
[ 12.691593] ehci_hcd 0000:00:1d.0: LPM: no device attached
[ 12.691945] usb 2-1: udev 2, busnum 2, minor = 129
[ 12.691951] usb 2-1: New USB device found, idVendor=8087, idProduct=0020
[ 12.693656] usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 12.695749] usb 2-1: usb_probe_device
[ 12.695759] usb 2-1: configuration #1 chosen from 1 choice
[ 12.696004] usb 2-1: adding 2-1:1.0 (config #1, interface 0)
[ 12.696205] hub 2-1:1.0: usb_probe_interface
[ 12.696213] hub 2-1:1.0: usb_probe_interface - got id
[ 12.696220] hub 2-1:1.0: USB hub found
[ 12.699847] hub 2-1:1.0: 8 ports detected
[ 12.701555] hub 2-1:1.0: standalone hub
[ 12.701557] hub 2-1:1.0: individual port power switching
[ 12.701559] hub 2-1:1.0: individual port over-current protection
[ 12.701561] hub 2-1:1.0: Single TT
[ 12.701563] hub 2-1:1.0: TT requires at most 8 FS bit times (666 ns)
[ 12.701565] hub 2-1:1.0: Port indicators are supported
[ 12.701567] hub 2-1:1.0: power on to power good time: 100ms
[ 12.701933] hub 2-1:1.0: local power source is good
[ 12.701943] hub 2-1:1.0: enabling power on all ports
[ 12.702998] hub 1-0:1.0: state 7 ports 3 chg 0002 evt 0000
[ 12.703016] hub 1-0:1.0: port 1, status 0501, change 0000, 480 Mb/s
[ 12.755573] ehci_hcd 0000:00:1a.0: port 1 high speed
[ 12.755582] ehci_hcd 0000:00:1a.0: GetStatus port:1 status 001005 0 ACK POWER sig=se0 PE CONNECT
[ 12.791917] input: HP WMI hotkeys as /devices/virtual/input/input7
[ 12.800555] hub 2-1:1.0: port 5: status 0101 change 0001
[ 12.800864] hub 2-1:1.0: port 6: status 0101 change 0001
[ 12.811323] usb 1-1: new high speed USB device number 2 using ehci_hcd
[ 12.867515] ehci_hcd 0000:00:1a.0: port 1 high speed
[ 12.867531] ehci_hcd 0000:00:1a.0: GetStatus port:1 status 001005 0 ACK POWER sig=se0 PE CONNECT
[ 12.868828] sda: sda1 sda2 sda3 sda4 < sda5 sda6 >
[ 12.871606] sd 0:0:0:0: [sda] Attached SCSI disk
[ 12.899234] usb 2-1: link qh256-0001/ffff88015347fb00 start 1 [1/0 us]
[ 12.943445] ehci_hcd 0000:00:1a.0: set dev address 2 for port 1
[ 12.943452] ehci_hcd 0000:00:1a.0: LPM: no device attached
[ 12.943816] usb 1-1: udev 2, busnum 1, minor = 1
[ 12.943821] usb 1-1: New USB device found, idVendor=8087, idProduct=0020
[ 12.946205] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 12.950078] usb 1-1: usb_probe_device
[ 12.950089] usb 1-1: configuration #1 chosen from 1 choice
[ 12.950334] usb 1-1: adding 1-1:1.0 (config #1, interface 0)
[ 12.950533] hub 1-1:1.0: usb_probe_interface
[ 12.950541] hub 1-1:1.0: usb_probe_interface - got id
[ 12.950548] hub 1-1:1.0: USB hub found
[ 12.954200] hub 1-1:1.0: 6 ports detected
[ 12.955937] hub 1-1:1.0: standalone hub
[ 12.955940] hub 1-1:1.0: individual port power switching
[ 12.955942] hub 1-1:1.0: individual port over-current protection
[ 12.955944] hub 1-1:1.0: Single TT
[ 12.955946] hub 1-1:1.0: TT requires at most 8 FS bit times (666 ns)
[ 12.955948] hub 1-1:1.0: Port indicators are supported
[ 12.955951] hub 1-1:1.0: power on to power good time: 100ms
[ 12.956464] hub 1-1:1.0: local power source is good
[ 12.956474] hub 1-1:1.0: enabling power on all ports
[ 12.957347] hub 2-1:1.0: state 7 ports 8 chg 0060 evt 0000
[ 12.957543] hub 2-1:1.0: port 5, status 0101, change 0000, 12 Mb/s
[ 13.027312] usb 2-1.5: new full speed USB device number 3 using ehci_hcd
[ 13.055814] hub 1-1:1.0: port 3: status 0101 change 0001
[ 13.056096] hub 1-1:1.0: port 4: status 0101 change 0001
[ 13.123140] usb 2-1.5: ep0 maxpacket = 8
[ 13.125083] usb 2-1.5: skipped 1 descriptor after interface
[ 13.125094] usb 2-1.5: skipped 1 descriptor after interface
[ 13.125311] usb 2-1.5: default language 0x0409
[ 13.126068] usb 2-1.5: udev 3, busnum 2, minor = 130
[ 13.126077] usb 2-1.5: New USB device found, idVendor=056a, idProduct=00e3
[ 13.129564] usb 2-1.5: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 13.133160] usb 2-1.5: Product: ISD-V4
[ 13.136578] usb 2-1.5: Manufacturer: Tablet
[ 13.140440] usb 2-1.5: usb_probe_device
[ 13.140449] usb 2-1.5: configuration #1 chosen from 1 choice
[ 13.140773] usb 2-1.5: adding 2-1.5:1.0 (config #1, interface 0)
[ 13.140994] usbhid 2-1.5:1.0: usb_probe_interface
[ 13.141002] usbhid 2-1.5:1.0: usb_probe_interface - got id
[ 13.141079] usb 2-1.5: adding 2-1.5:1.1 (config #1, interface 1)
[ 13.141286] usbhid 2-1.5:1.1: usb_probe_interface
[ 13.141294] usbhid 2-1.5:1.1: usb_probe_interface - got id
[ 13.141554] hub 2-1:1.0: port 6, status 0101, change 0000, 12 Mb/s
[ 13.155076] usb 1-1: link qh256-0001/ffff8801577d5180 start 1 [1/0 us]
[ 13.211211] usb 2-1.6: new high speed USB device number 4 using ehci_hcd
[ 13.288278] Synaptics Touchpad, model: 1, fw: 7.4, id: 0x1e0b1, caps: 0xd04773/0xe40000/0x5a0400
[ 13.321240] usb 2-1.6: skipped 1 descriptor after configuration
[ 13.321246] usb 2-1.6: skipped 6 descriptors after interface
[ 13.321251] usb 2-1.6: skipped 1 descriptor after endpoint
[ 13.321255] usb 2-1.6: skipped 6 descriptors after interface
[ 13.321780] usb 2-1.6: default language 0x0409
[ 13.324753] usb 2-1.6: udev 4, busnum 2, minor = 131
[ 13.324763] usb 2-1.6: New USB device found, idVendor=10f1, idProduct=1a16
[ 13.327295] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio4/input/input8
[ 13.329624] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[ 13.329697] HDA Intel 0000:00:1b.0: setting latency timer to 64
[ 13.335966] usb 2-1.6: New USB device strings: Mfr=2, Product=1, SerialNumber=0
[ 13.339844] usb 2-1.6: Product: HP Webcam
[ 13.343679] usb 2-1.6: Manufacturer: Importek
[ 13.347829] usb 2-1.6: usb_probe_device
[ 13.347834] usb 2-1.6: configuration #1 chosen from 1 choice
[ 13.348371] usb 2-1.6: adding 2-1.6:1.0 (config #1, interface 0)
[ 13.349967] usb 2-1.6: adding 2-1.6:1.1 (config #1, interface 1)
[ 13.350249] hub 2-1:1.0: state 7 ports 8 chg 0000 evt 0040
[ 13.350459] hub 1-1:1.0: state 7 ports 6 chg 0018 evt 0000
[ 13.350590] hub 1-1:1.0: port 3, status 0101, change 0000, 12 Mb/s
[ 13.423209] usb 1-1.3: new full speed USB device number 3 using ehci_hcd
[ 13.521816] usb 1-1.3: skipped 1 descriptor after interface
[ 13.522053] usb 1-1.3: default language 0x0409
[ 13.522817] usb 1-1.3: udev 3, busnum 1, minor = 2
[ 13.522821] usb 1-1.3: New USB device found, idVendor=03f0, idProduct=231d
[ 13.524932] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 13.527052] usb 1-1.3: Product: HP Integrated Module
[ 13.529144] usb 1-1.3: Manufacturer: Broadcom Corp
[ 13.531353] usb 1-1.3: usb_probe_device
[ 13.531357] usb 1-1.3: configuration #1 chosen from 1 choice
[ 13.531564] usb 1-1.3: adding 1-1.3:1.0 (config #1, interface 0)
[ 13.531687] usb 1-1.3: adding 1-1.3:1.1 (config #1, interface 1)
[ 13.531787] usb 1-1.3: adding 1-1.3:1.2 (config #1, interface 2)
[ 13.531877] usb 1-1.3: adding 1-1.3:1.3 (config #1, interface 3)
[ 13.532067] hub 1-1:1.0: port 4, status 0101, change 0000, 12 Mb/s
[ 13.602915] usb 1-1.4: new full speed USB device number 4 using ehci_hcd
[ 13.694696] usb 1-1.4: ep0 maxpacket = 8
[ 13.696233] usb 1-1.4: default language 0x0409
[ 13.696621] usb 1-1.4: udev 4, busnum 1, minor = 3
[ 13.696625] usb 1-1.4: New USB device found, idVendor=138a, idProduct=0005
[ 13.698775] usb 1-1.4: New USB device strings: Mfr=0, Product=0, SerialNumber=1
[ 13.700907] usb 1-1.4: SerialNumber: 0510f9f55000
[ 13.703156] usb 1-1.4: usb_probe_device
[ 13.703161] usb 1-1.4: configuration #1 chosen from 1 choice
[ 13.703352] usb 1-1.4: adding 1-1.4:1.0 (config #1, interface 0)
[ 13.703492] hub 1-1:1.0: state 7 ports 6 chg 0000 evt 0008
[ 14.385598] HDA Intel 0000:01:00.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 14.389570] HDA Intel 0000:01:00.1: setting latency timer to 64
[ 14.402490] hda-intel: Enable sync_write for AMD chipset
[ 14.407263] usbcore: registered new interface driver snd-usb-audio
[ 14.411299] ALSA device list:
[ 14.415216] #0: HDA Intel at 0xc4500000 irq 22
[ 14.419120] #1: HD-Audio Generic at 0xc4420000 irq 17
[ 14.423114] IPv4 over IPv4 tunneling driver
[ 14.427731] tunl0: Features changed: 0x00007800 -> 0x00007000
[ 14.431770] TCP cubic registered
[ 14.436527] NET: Registered protocol family 10
[ 14.440982] IPv6 over IPv4 tunneling driver
[ 14.445327] sit0: Features changed: 0x00007800 -> 0x00007000
[ 14.449278] NET: Registered protocol family 17
[ 14.452919] lib80211: common routines for IEEE802.11 drivers
[ 14.456513] lib80211_crypt: registered algorithm 'NULL'
[ 14.457224] PM: Hibernation image not present or could not be loaded.
[ 14.458153] rtc_cmos 00:06: setting system clock to 2011-05-18 12:41:26 UTC (1305722486)
[ 14.479960] EXT3-fs: barriers not enabled
[ 14.490031] kjournald starting. Commit interval 5 seconds
[ 14.490076] EXT3-fs (sda1): mounted filesystem with ordered data mode
[ 14.490092] VFS: Mounted root (ext3 filesystem) readonly on device 8:1.
[ 14.496428] Freeing unused kernel memory: 448k freed
[ 15.715260] udev: starting version 151
[ 15.715393] udevd (1264): /proc/1264/oom_adj is deprecated, please use /proc/1264/oom_score_adj instead.
[ 15.862265] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[ 15.862295] r8169 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 15.862361] r8169 0000:02:00.0: setting latency timer to 64
[ 15.862374] r8169 0000:02:00.0: no MSI. Back to INTx.
[ 15.862475] r8169 0000:02:00.0: eth0: Features changed: 0x20004980 -> 0x20004180
[ 15.862567] r8169 0000:02:00.0: eth0: RTL8168d/8111d at 0xffffc900101f8000, d8:d3:85:39:89:fb, XID 083000c0 IRQ 16
[ 15.873734] brcmutil: module is from the staging directory, the quality is unknown, you have been warned.
[ 15.927370] brcmsmac: module is from the staging directory, the quality is unknown, you have been warned.
[ 15.928798] brcmsmac 0000:03:00.0: bus 3 slot 0 func 0 irq 10
[ 15.928820] brcmsmac 0000:03:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 15.928829] brcmsmac 0000:03:00.0: setting latency timer to 64
[ 15.983858] wacom 2-1.5:1.0: usb_probe_interface
[ 15.983864] wacom 2-1.5:1.0: usb_probe_interface - got id
[ 15.988408] input: Wacom ISDv4 E3 Finger as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.5/2-1.5:1.0/input/input9
[ 15.992389] wacom 2-1.5:1.1: usb_probe_interface
[ 15.992401] wacom 2-1.5:1.1: usb_probe_interface - got id
[ 15.994875] input: Wacom ISDv4 E3 Pen as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.5/2-1.5:1.1/input/input10
[ 15.998675] usbcore: registered new interface driver wacom
[ 15.998682] wacom: v1.52:USB Wacom tablet driver
[ 16.129446] Found chip type AI (0x13814313)
[ 16.139070] Applying 4313 WARs
[ 16.140160] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 16.140333] brcmsmac 0000:03:00.0: wlan0: Features changed: 0x00004800 -> 0x00004000
[ 17.427894] EXT3-fs (sda1): using internal journal
[ 17.545863] EXT3-fs: barriers not enabled
[ 17.560183] kjournald starting. Commit interval 5 seconds
[ 17.560350] EXT3-fs (sda3): warning: maximal mount count reached, running e2fsck is recommended
[ 17.560602] EXT3-fs (sda3): using internal journal
[ 17.560610] EXT3-fs (sda3): mounted filesystem with ordered data mode
[ 17.578158] EXT3-fs: barriers not enabled
[ 17.578518] kjournald starting. Commit interval 5 seconds
[ 17.578791] EXT3-fs (sda5): using internal journal
[ 17.578801] EXT3-fs (sda5): mounted filesystem with ordered data mode
[ 19.409477] r8169 0000:02:00.0: eth0: unable to load firmware patch rtl_nic/rtl8168d-2.fw (-2)
[ 19.416715] r8169 0000:02:00.0: eth0: link down
[ 19.417830] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 19.633889] ieee80211 phy0: wl_ops_bss_info_changed: BSS idle: true (implement)
[ 19.633911] ieee80211 phy0: wl_ops_config: change monitor mode: false (implement)
[ 19.633919] ieee80211 phy0: wl_ops_config: change power-save mode: false (implement)
[ 19.634497] ieee80211 phy0: wl_ops_bss_info_changed: qos enabled: false (implement)
[ 19.635637] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 20.019692] ieee80211 phy0: wl_ops_bss_info_changed: BSS idle: false (implement)
[ 20.106275] Adding 4000180k swap on /dev/sda2. Priority:-1 extents:1 across:4000180k
More information about the Intel-gfx
mailing list