[Intel-gfx] [PATCH v2] drm/i915: only enable sdvo hotplug irq if needed

[Jani Nikula]

Avoid constant wakeups caused by noisy irq lines when we don't even care
about the irq. This should be particularly useful for i945g/gm where the
hotplug has been disabled:

commit 768b107e4b3be0acf6f58e914afe4f337c00932b
Author: Daniel Vetter <daniel.vetter at ffwll.ch>
Date:   Fri May 4 11:29:56 2012 +0200

    drm/i915: disable sdvo hotplug on i945g/gm

v2: While at it, remove the bogus hotplug_active read, and do not mask
hotplug_active[0] before checking whether the irq is needed, per discussion
with Daniel on IRC.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=38442
Signed-off-by: Jani Nikula <jani.nikula at intel.com>

---

N.B. This really needs a Tested-by from the bug reporter.
---
 drivers/gpu/drm/i915/intel_sdvo.c |   15 ++++++---------
 1 file changed, 6 insertions(+), 9 deletions(-)

diff --git a/drivers/gpu/drm/i915/intel_sdvo.c b/drivers/gpu/drm/i915/intel_sdvo.c
index d81bb0b..123afd3 100644
--- a/drivers/gpu/drm/i915/intel_sdvo.c
+++ b/drivers/gpu/drm/i915/intel_sdvo.c
@@ -2573,7 +2573,6 @@ bool intel_sdvo_init(struct drm_device *dev, uint32_t sdvo_reg, bool is_sdvob)
 		hotplug_mask = intel_sdvo->is_sdvob ?
 			SDVOB_HOTPLUG_INT_STATUS_I915 : SDVOC_HOTPLUG_INT_STATUS_I915;
 	}
-	dev_priv->hotplug_supported_mask |= hotplug_mask;
 
 	drm_encoder_helper_add(&intel_encoder->base, &intel_sdvo_helper_funcs);
 
@@ -2581,14 +2580,6 @@ bool intel_sdvo_init(struct drm_device *dev, uint32_t sdvo_reg, bool is_sdvob)
 	if (!intel_sdvo_get_capabilities(intel_sdvo, &intel_sdvo->caps))
 		goto err;
 
-	/* Set up hotplug command - note paranoia about contents of reply.
-	 * We assume that the hardware is in a sane state, and only touch
-	 * the bits we think we understand.
-	 */
-	intel_sdvo_get_value(intel_sdvo, SDVO_CMD_GET_ACTIVE_HOT_PLUG,
-			     &intel_sdvo->hotplug_active, 2);
-	intel_sdvo->hotplug_active[0] &= ~0x3;
-
 	if (intel_sdvo_output_setup(intel_sdvo,
 				    intel_sdvo->caps.output_flags) != true) {
 		DRM_DEBUG_KMS("SDVO output failed to setup on %s\n",
@@ -2596,6 +2587,12 @@ bool intel_sdvo_init(struct drm_device *dev, uint32_t sdvo_reg, bool is_sdvob)
 		goto err;
 	}
 
+	/* Only enable the hotplug irq if we need it, to work around noisy
+	 * hotplug lines.
+	 */
+	if (intel_sdvo->hotplug_active[0])
+		dev_priv->hotplug_supported_mask |= hotplug_mask;
+
 	intel_sdvo_select_ddc_bus(dev_priv, intel_sdvo, sdvo_reg);
 
 	/* Set the input timing to the screen. Assume always input 0. */
-- 
1.7.9.5