[Intel-gfx] xf86-video-intel 2.20.5 does not detect PCI_CHIP_SANDYBRIDGE_M_GT1
Christian Gmeiner
christian.gmeiner at gmail.com
Thu Aug 30 10:23:04 CEST 2012
The problem is that xorg uses fbdev driver instead of the intel one.
[ 13.843] (**) FBDEV(1): claimed PCI slot 0 at 0:2:0
[ 13.843] (II) FBDEV(1): using default device
[ 13.843] (WW) VGA arbiter: cannot open kernel arbiter, no multi-card support
[ 13.843] (II) FBDEV(1): Creating default Display subsection in
Screen section
"Default Screen Section" for depth/fbbpp 24/32
[ 13.843] (==) FBDEV(1): Depth 24, (==) framebuffer bpp 32
[ 13.843] (==) FBDEV(1): RGB weight 888
[ 13.843] (==) FBDEV(1): Default visual is TrueColor
[ 13.843] (==) FBDEV(1): Using gamma correction (1.0, 1.0, 1.0)
[ 13.843] (II) FBDEV(1): hardware: VESA VGA (video memory: 1216kB)
[ 13.843] (II) FBDEV(1): checking modes against framebuffer device...
[ 13.843] (II) FBDEV(1): checking modes against monitor...
[ 13.843] (--) FBDEV(1): Virtual size is 640x480 (pitch 640)
[ 13.843] (**) FBDEV(1): Built-in mode "current": 30.7 MHz, 36.9
kHz, 73.3 Hz
[ 13.844] (II) FBDEV(1): Modeline "current"x0.0 30.72 640 672
752 832 480 484 488 504 -hsync -vsync -csync (36.9 kHz)
[ 13.844] (==) FBDEV(1): DPI set to (96, 96)
Christian Gmeiner, MSc
2012/8/30 Zhang, Xiong Y <xiong.y.zhang at intel.com>:
> I think vesafb driver should not run.
> But in following dmesg, I see vesafb driver running before drm driver.
>
> -----Original Message-----
> From: intel-gfx-bounces+xiong.y.zhang=intel.com at lists.freedesktop.org [mailto:intel-gfx-bounces+xiong.y.zhang=intel.com at lists.freedesktop.org] On Behalf Of Christian Gmeiner
> Sent: Thursday, August 30, 2012 3:43 PM
> To: intel-gfx at lists.freedesktop.org
> Subject: [Intel-gfx] xf86-video-intel 2.20.5 does not detect PCI_CHIP_SANDYBRIDGE_M_GT1
>
> Hi all,
>
> I am trying to get the following Intel hardware working with recent
> Intel driver.
>
> 00:02.0 VGA compatible controller [0300]: Intel Corporation Sandy
> Bridge Integrated Graphics Controller [8086:0106] (rev 09) (prog-if 00
> [VGA controller])
> Subsystem: Intel Corporation Device [8086:2010]
> Flags: bus master, fast devsel, latency 0, IRQ 42
> Memory at f7800000 (64-bit, non-prefetchable) [size=4M]
> Memory at e0000000 (64-bit, prefetchable) [size=256M]
> I/O ports at f000 [size=64]
> Expansion ROM at <unassigned> [disabled]
> Capabilities: [90] MSI: Enable+ Count=1/1 Maskable- 64bit-
> Capabilities: [d0] Power Management version 2
> Capabilities: [a4] PCI Advanced Features
> Kernel driver in use: i915
> Kernel modules: i915
>
> I think that all SW requirements are met :) Here are some detailed informations.
>
>
> root at OT:~# dmesg
> [ 0.000000] Initializing cgroup subsys cpu
> [ 0.000000] Linux version 3.5.3-bachmann (christian at chgm-pc) (gcc
> version 4.6.3 (Ubuntu/Linaro 4.6.3-1ubuntu5) ) #2 SMP PREEMPT Mon Aug
> 27 13:25:26 CEST 2012
> [ 0.000000] KERNEL supported cpus:
> [ 0.000000] Intel GenuineIntel
> [ 0.000000] AMD AuthenticAMD
> [ 0.000000] e820: BIOS-provided physical RAM map:
> [ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009d7ff] usable
> [ 0.000000] BIOS-e820: [mem 0x000000000009d800-0x000000000009ffff] reserved
> [ 0.000000] BIOS-e820: [mem 0x00000000000e0000-0x00000000000fffff] reserved
> [ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000001fffffff] usable
> [ 0.000000] BIOS-e820: [mem 0x0000000020000000-0x00000000201fffff] reserved
> [ 0.000000] BIOS-e820: [mem 0x0000000020200000-0x000000003fffffff] usable
> [ 0.000000] BIOS-e820: [mem 0x0000000040000000-0x00000000401fffff] reserved
> [ 0.000000] BIOS-e820: [mem 0x0000000040200000-0x00000000d9cd3fff] usable
> [ 0.000000] BIOS-e820: [mem 0x00000000d9cd4000-0x00000000da279fff] reserved
> [ 0.000000] BIOS-e820: [mem 0x00000000da27a000-0x00000000da303fff] usable
> [ 0.000000] BIOS-e820: [mem 0x00000000da304000-0x00000000da39cfff] ACPI NVS
> [ 0.000000] BIOS-e820: [mem 0x00000000da39d000-0x00000000da751fff] reserved
> [ 0.000000] BIOS-e820: [mem 0x00000000da752000-0x00000000da752fff] usable
> [ 0.000000] BIOS-e820: [mem 0x00000000da753000-0x00000000da795fff] ACPI NVS
> [ 0.000000] BIOS-e820: [mem 0x00000000da796000-0x00000000dadfefff] usable
> [ 0.000000] BIOS-e820: [mem 0x00000000dadff000-0x00000000daff1fff] reserved
> [ 0.000000] BIOS-e820: [mem 0x00000000daff2000-0x00000000daffffff] usable
> [ 0.000000] BIOS-e820: [mem 0x00000000db800000-0x00000000df9fffff] reserved
> [ 0.000000] BIOS-e820: [mem 0x00000000f8000000-0x00000000fbffffff] reserved
> [ 0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000fec00fff] reserved
> [ 0.000000] BIOS-e820: [mem 0x00000000fed00000-0x00000000fed03fff] reserved
> [ 0.000000] BIOS-e820: [mem 0x00000000fed1c000-0x00000000fed1ffff] reserved
> [ 0.000000] BIOS-e820: [mem 0x00000000fee00000-0x00000000fee00fff] reserved
> [ 0.000000] BIOS-e820: [mem 0x00000000ff000000-0x00000000ffffffff] reserved
> [ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000011f5fffff] usable
> [ 0.000000] Notice: NX (Execute Disable) protection cannot be
> enabled: non-PAE kernel!
> [ 0.000000] DMI 2.7 present.
> [ 0.000000] DMI: To be filled by O.E.M. To be filled by
> O.E.M./C6B-7S, BIOS X1.00b 08/14/2012
> [ 0.000000] e820: update [mem 0x00000000-0x0000ffff] usable ==> reserved
> [ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
> [ 0.000000] e820: last_pfn = 0xdb000 max_arch_pfn = 0x100000
> [ 0.000000] MTRR default type: uncachable
> [ 0.000000] MTRR fixed ranges enabled:
> [ 0.000000] 00000-9FFFF write-back
> [ 0.000000] A0000-BFFFF uncachable
> [ 0.000000] C0000-CFFFF write-protect
> [ 0.000000] D0000-E7FFF uncachable
> [ 0.000000] E8000-FFFFF write-protect
> [ 0.000000] MTRR variable ranges enabled:
> [ 0.000000] 0 base 000000000 mask F00000000 write-back
> [ 0.000000] 1 base 100000000 mask FE0000000 write-back
> [ 0.000000] 2 base 0E0000000 mask FE0000000 uncachable
> [ 0.000000] 3 base 0DC000000 mask FFC000000 uncachable
> [ 0.000000] 4 base 0DB800000 mask FFF800000 uncachable
> [ 0.000000] 5 base 11F800000 mask FFF800000 uncachable
> [ 0.000000] 6 base 11F600000 mask FFFE00000 uncachable
> [ 0.000000] 7 disabled
> [ 0.000000] 8 disabled
> [ 0.000000] 9 disabled
> [ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
> [ 0.000000] e820: update [mem 0xdb800000-0xffffffff] usable ==> reserved
> [ 0.000000] found SMP MP-table at [mem 0x000fd680-0x000fd68f]
> mapped at [c00fd680]
> [ 0.000000] initial memory mapped: [mem 0x00000000-0x017fffff]
> [ 0.000000] Base memory trampoline at [c0099000] 99000 size 16384
> [ 0.000000] init_memory_mapping: [mem 0x00000000-0x377fdfff]
> [ 0.000000] [mem 0x00000000-0x003fffff] page 4k
> [ 0.000000] [mem 0x00400000-0x373fffff] page 2M
> [ 0.000000] [mem 0x37400000-0x377fdfff] page 4k
> [ 0.000000] kernel direct mapping tables up to 0x377fdfff @ [mem
> 0x017fa000-0x017fffff]
> [ 0.000000] RAMDISK: [mem 0x16772000-0x1803ffff]
> [ 0.000000] ACPI: RSDP 000f0490 00024 (v02 ALASKA)
> [ 0.000000] ACPI: XSDT da38f078 0006C (v01 ALASKA A M I 01072009
> AMI 00010013)
> [ 0.000000] ACPI: FACP da398580 0010C (v05 ALASKA A M I 01072009
> AMI 00010013)
> [ 0.000000] ACPI: DSDT da38f178 09402 (v02 ALASKA A M I 00000022
> INTL 20051117)
> [ 0.000000] ACPI: FACS da39b080 00040
> [ 0.000000] ACPI: APIC da398690 00062 (v03 ALASKA A M I 01072009
> AMI 00010013)
> [ 0.000000] ACPI: FPDT da3986f8 00044 (v01 ALASKA A M I 01072009
> AMI 00010013)
> [ 0.000000] ACPI: ASF! da398740 000A5 (v32 INTEL HCG 00000001
> TFSM 000F4240)
> [ 0.000000] ACPI: MCFG da3987e8 0003C (v01 ALASKA A M I 01072009
> MSFT 00000097)
> [ 0.000000] ACPI: HPET da398828 00038 (v01 ALASKA A M I 01072009
> AMI. 00000005)
> [ 0.000000] ACPI: SSDT da398860 00315 (v01 SataRe SataTabl 00001000
> INTL 20091112)
> [ 0.000000] ACPI: SSDT da398b78 00692 (v01 PmRef Cpu0Ist 00003000
> INTL 20051117)
> [ 0.000000] ACPI: SSDT da399210 00A92 (v01 PmRef CpuPm 00003000
> INTL 20051117)
> [ 0.000000] ACPI: Local APIC address 0xfee00000
> [ 0.000000] 2616MB HIGHMEM available.
> [ 0.000000] 887MB LOWMEM available.
> [ 0.000000] mapped low ram: 0 - 377fe000
> [ 0.000000] low ram: 0 - 377fe000
> [ 0.000000] Zone ranges:
> [ 0.000000] DMA [mem 0x00010000-0x00ffffff]
> [ 0.000000] Normal [mem 0x01000000-0x377fdfff]
> [ 0.000000] HighMem [mem 0x377fe000-0xdaffffff]
> [ 0.000000] Movable zone start for each node
> [ 0.000000] Early memory node ranges
> [ 0.000000] node 0: [mem 0x00010000-0x0009cfff]
> [ 0.000000] node 0: [mem 0x00100000-0x1fffffff]
> [ 0.000000] node 0: [mem 0x20200000-0x3fffffff]
> [ 0.000000] node 0: [mem 0x40200000-0xd9cd3fff]
> [ 0.000000] node 0: [mem 0xda27a000-0xda303fff]
> [ 0.000000] node 0: [mem 0xda752000-0xda752fff]
> [ 0.000000] node 0: [mem 0xda796000-0xdadfefff]
> [ 0.000000] node 0: [mem 0xdaff2000-0xdaffffff]
> [ 0.000000] On node 0 totalpages: 892771
> [ 0.000000] free_area_init_node: node 0, pgdat c13e3280,
> node_mem_map f5c9d200
> [ 0.000000] DMA zone: 32 pages used for memmap
> [ 0.000000] DMA zone: 0 pages reserved
> [ 0.000000] DMA zone: 3949 pages, LIFO batch:0
> [ 0.000000] Normal zone: 1744 pages used for memmap
> [ 0.000000] Normal zone: 220974 pages, LIFO batch:31
> [ 0.000000] HighMem zone: 5233 pages used for memmap
> [ 0.000000] HighMem zone: 660839 pages, LIFO batch:31
> [ 0.000000] Using APIC driver default
> [ 0.000000] ACPI: Local APIC address 0xfee00000
> [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
> [ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled)
> [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0xff] high edge lint[0x1])
> [ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
> [ 0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
> [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
> [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
> [ 0.000000] ACPI: IRQ0 used by override.
> [ 0.000000] ACPI: IRQ2 used by override.
> [ 0.000000] ACPI: IRQ9 used by override.
> [ 0.000000] Using ACPI (MADT) for SMP configuration information
> [ 0.000000] ACPI: HPET id: 0x8086a701 base: 0xfed00000
> [ 0.000000] SMP: Allowing 2 CPUs, 0 hotplug CPUs
> [ 0.000000] nr_irqs_gsi: 40
> [ 0.000000] e820: [mem 0xdfa00000-0xf7ffffff] available for PCI devices
> [ 0.000000] setup_percpu: NR_CPUS:4 nr_cpumask_bits:4 nr_cpu_ids:2
> nr_node_ids:1
> [ 0.000000] PERCPU: Embedded 11 pages/cpu @f5c75000 s24256 r0 d20800 u45056
> [ 0.000000] pcpu-alloc: s24256 r0 d20800 u45056 alloc=11*4096
> [ 0.000000] pcpu-alloc: [0] 0 [0] 1
> [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.
> Total pages: 885762
> [ 0.000000] Kernel command line:
> BOOT_IMAGE=/boot/vmlinuz-3.5.3-bachmann root=/dev/sda2 ro rootwait
> splash vga=0x312 quiet
> [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
> [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
> [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
> [ 0.000000] __ex_table already sorted, skipping sort
> [ 0.000000] Initializing CPU#0
> [ 0.000000] xsave/xrstor: enabled xstate_bv 0x3, cntxt size 0x240
> [ 0.000000] Initializing HighMem for node 0 (000377fe:000db000)
> [ 0.000000] Memory: 3512120k/3588096k available (2798k kernel code,
> 58964k reserved, 1200k data, 320k init, 2664288k highmem)
> [ 0.000000] virtual kernel memory layout:
> [ 0.000000] fixmap : 0xfff66000 - 0xfffff000 ( 612 kB)
> [ 0.000000] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
> [ 0.000000] vmalloc : 0xf7ffe000 - 0xff7fe000 ( 120 MB)
> [ 0.000000] lowmem : 0xc0000000 - 0xf77fe000 ( 887 MB)
> [ 0.000000] .init : 0xc13e8000 - 0xc1438000 ( 320 kB)
> [ 0.000000] .data : 0xc12bb87e - 0xc13e7900 (1200 kB)
> [ 0.000000] .text : 0xc1000000 - 0xc12bb87e (2798 kB)
> [ 0.000000] Checking if this processor honours the WP bit even in
> supervisor mode...Ok.
> [ 0.000000] SLUB: Genslabs=15, HWalign=64, Order=0-3, MinObjects=0,
> CPUs=2, Nodes=1
> [ 0.000000] Preemptible hierarchical RCU implementation.
> [ 0.000000] NR_IRQS:2304 nr_irqs:512 16
> [ 0.000000] CPU 0 irqstacks, hard=f5408000 soft=f540a000
> [ 0.000000] Extended CMOS year: 2000
> [ 0.000000] Console: colour dummy device 80x25
> [ 0.000000] console [tty0] enabled
> [ 0.000000] hpet clockevent registered
> [ 0.000000] Fast TSC calibration using PIT
> [ 0.002000] Detected 1097.446 MHz processor.
> [ 0.000001] Calibrating delay loop (skipped), value calculated
> using timer frequency.. 2194.89 BogoMIPS (lpj=1097446)
> [ 0.000006] pid_max: default: 32768 minimum: 301
> [ 0.000052] Mount-cache hash table entries: 512
> [ 0.000354] CPU: Physical Processor ID: 0
> [ 0.000356] CPU: Processor Core ID: 0
> [ 0.000363] ENERGY_PERF_BIAS: Set to 'normal', was 'performance'
> [ 0.000363] ENERGY_PERF_BIAS: View and update with x86_energy_perf_policy(8)
> [ 0.000368] using mwait in idle threads.
> [ 0.000568] Freeing SMP alternatives: 12k freed
> [ 0.000573] ACPI: Core revision 20120320
> [ 0.011463] Enabling APIC mode: Flat. Using 1 I/O APICs
> [ 0.011884] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
> [ 0.021887] CPU0: Intel(R) Celeron(R) CPU 847E @ 1.10GHz stepping 07
> [ 0.224973] Performance Events: PEBS fmt1+, 16-deep LBR,
> SandyBridge events, Intel PMU driver.
> [ 0.224983] PEBS disabled due to CPU errata.
> [ 0.224987] ... version: 3
> [ 0.224989] ... bit width: 48
> [ 0.224990] ... generic registers: 8
> [ 0.224993] ... value mask: 0000ffffffffffff
> [ 0.224995] ... max period: 000000007fffffff
> [ 0.224997] ... fixed-purpose events: 3
> [ 0.224999] ... event mask: 00000007000000ff
> [ 0.234984] CPU 1 irqstacks, hard=f547c000 soft=f547e000
> [ 0.234987] Booting Node 0, Processors #1 Ok.
> [ 0.245424] Initializing CPU#1
> [ 0.248222] Brought up 2 CPUs
> [ 0.248227] Total of 2 processors activated (4389.78 BogoMIPS).
> [ 0.250308] devtmpfs: initialized
> [ 0.250749] NET: Registered protocol family 16
> [ 0.251308] ACPI FADT declares the system doesn't support PCIe
> ASPM, so disable it
> [ 0.251311] ACPI: bus type pci registered
> [ 0.251428] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem
> 0xf8000000-0xfbffffff] (base 0xf8000000)
> [ 0.251433] PCI: MMCONFIG at [mem 0xf8000000-0xfbffffff] reserved in E820
> [ 0.251435] PCI: Using MMCONFIG for extended config space
> [ 0.251437] PCI: Using configuration type 1 for base access
> [ 0.254756] bio: create slab <bio-0> at 0
> [ 0.254902] ACPI: Added _OSI(Module Device)
> [ 0.254907] ACPI: Added _OSI(Processor Device)
> [ 0.254909] ACPI: Added _OSI(3.0 _SCP Extensions)
> [ 0.254912] ACPI: Added _OSI(Processor Aggregator Device)
> [ 0.257676] ACPI: EC: Look up EC in DSDT
> [ 0.271296] ACPI: Executed 1 blocks of module-level executable AML code
> [ 0.279794] ACPI: SSDT da227018 0083B (v01 PmRef Cpu0Cst 00003001
> INTL 20051117)
> [ 0.280541] ACPI: Dynamic OEM Table Load:
> [ 0.280545] ACPI: SSDT (null) 0083B (v01 PmRef Cpu0Cst 00003001
> INTL 20051117)
> [ 0.283483] ACPI: SSDT da228a98 00303 (v01 PmRef ApIst 00003000
> INTL 20051117)
> [ 0.284293] ACPI: Dynamic OEM Table Load:
> [ 0.284297] ACPI: SSDT (null) 00303 (v01 PmRef ApIst 00003000
> INTL 20051117)
> [ 0.287180] ACPI: SSDT da229c18 00119 (v01 PmRef ApCst 00003000
> INTL 20051117)
> [ 0.287898] ACPI: Dynamic OEM Table Load:
> [ 0.287902] ACPI: SSDT (null) 00119 (v01 PmRef ApCst 00003000
> INTL 20051117)
> [ 0.301040] ACPI: Interpreter enabled
> [ 0.301043] ACPI: (supports S0 S5)
> [ 0.301062] ACPI: Using IOAPIC for interrupt routing
> [ 0.336865] PCI: Using host bridge windows from ACPI; if necessary,
> use "pci=nocrs" and report a bug
> [ 0.337564] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-3e])
> [ 0.338516] pci_root PNP0A08:00: host bridge window [io 0x0000-0x0cf7]
> [ 0.338521] pci_root PNP0A08:00: host bridge window [io 0x0d00-0xffff]
> [ 0.338525] pci_root PNP0A08:00: host bridge window [mem
> 0x000a0000-0x000bffff]
> [ 0.338529] pci_root PNP0A08:00: host bridge window [mem
> 0x000d0000-0x000d3fff]
> [ 0.338532] pci_root PNP0A08:00: host bridge window [mem
> 0x000d4000-0x000d7fff]
> [ 0.338536] pci_root PNP0A08:00: host bridge window [mem
> 0x000d8000-0x000dbfff]
> [ 0.338539] pci_root PNP0A08:00: host bridge window [mem
> 0x000dc000-0x000dffff]
> [ 0.338542] pci_root PNP0A08:00: host bridge window [mem
> 0x000e0000-0x000e3fff]
> [ 0.338546] pci_root PNP0A08:00: host bridge window [mem
> 0x000e4000-0x000e7fff]
> [ 0.338550] pci_root PNP0A08:00: host bridge window [mem
> 0xdfa00000-0xfeafffff]
> [ 0.338620] PCI host bridge to bus 0000:00
> [ 0.338628] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7]
> [ 0.338632] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff]
> [ 0.338636] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff]
> [ 0.338640] pci_bus 0000:00: root bus resource [mem 0x000d0000-0x000d3fff]
> [ 0.338643] pci_bus 0000:00: root bus resource [mem 0x000d4000-0x000d7fff]
> [ 0.338646] pci_bus 0000:00: root bus resource [mem 0x000d8000-0x000dbfff]
> [ 0.338650] pci_bus 0000:00: root bus resource [mem 0x000dc000-0x000dffff]
> [ 0.338653] pci_bus 0000:00: root bus resource [mem 0x000e0000-0x000e3fff]
> [ 0.338657] pci_bus 0000:00: root bus resource [mem 0x000e4000-0x000e7fff]
> [ 0.338660] pci_bus 0000:00: root bus resource [mem 0xdfa00000-0xfeafffff]
> [ 0.338676] pci 0000:00:00.0: [8086:0104] type 00 class 0x060000
> [ 0.338744] pci 0000:00:02.0: [8086:0106] type 00 class 0x030000
> [ 0.338766] pci 0000:00:02.0: reg 10: [mem 0xf7800000-0xf7bfffff 64bit]
> [ 0.338780] pci 0000:00:02.0: reg 18: [mem 0xe0000000-0xefffffff 64bit pref]
> [ 0.338790] pci 0000:00:02.0: reg 20: [io 0xf000-0xf03f]
> [ 0.338883] pci 0000:00:16.0: [8086:1e3a] type 00 class 0x078000
> [ 0.338915] pci 0000:00:16.0: reg 10: [mem 0xf7c2b000-0xf7c2b00f 64bit]
> [ 0.339019] pci 0000:00:16.0: PME# supported from D0 D3hot D3cold
> [ 0.339066] pci 0000:00:19.0: [8086:1502] type 00 class 0x020000
> [ 0.339093] pci 0000:00:19.0: reg 10: [mem 0xf7c00000-0xf7c1ffff]
> [ 0.339106] pci 0000:00:19.0: reg 14: [mem 0xf7c29000-0xf7c29fff]
> [ 0.339119] pci 0000:00:19.0: reg 18: [io 0xf080-0xf09f]
> [ 0.339223] pci 0000:00:19.0: PME# supported from D0 D3hot D3cold
> [ 0.339259] pci 0000:00:1a.0: [8086:1e2d] type 00 class 0x0c0320
> [ 0.339288] pci 0000:00:1a.0: reg 10: [mem 0xf7c28000-0xf7c283ff]
> [ 0.339414] pci 0000:00:1a.0: PME# supported from D0 D3hot D3cold
> [ 0.339451] pci 0000:00:1b.0: [8086:1e20] type 00 class 0x040300
> [ 0.339474] pci 0000:00:1b.0: reg 10: [mem 0xf7c20000-0xf7c23fff 64bit]
> [ 0.339573] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
> [ 0.339610] pci 0000:00:1d.0: [8086:1e26] type 00 class 0x0c0320
> [ 0.339640] pci 0000:00:1d.0: reg 10: [mem 0xf7c27000-0xf7c273ff]
> [ 0.339766] pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold
> [ 0.339800] pci 0000:00:1f.0: [8086:1e59] type 00 class 0x060100
> [ 0.339966] pci 0000:00:1f.2: [8086:1e03] type 00 class 0x010601
> [ 0.339994] pci 0000:00:1f.2: reg 10: [io 0xf0d0-0xf0d7]
> [ 0.340006] pci 0000:00:1f.2: reg 14: [io 0xf0c0-0xf0c3]
> [ 0.340019] pci 0000:00:1f.2: reg 18: [io 0xf0b0-0xf0b7]
> [ 0.340031] pci 0000:00:1f.2: reg 1c: [io 0xf0a0-0xf0a3]
> [ 0.340043] pci 0000:00:1f.2: reg 20: [io 0xf060-0xf07f]
> [ 0.340056] pci 0000:00:1f.2: reg 24: [mem 0xf7c26000-0xf7c267ff]
> [ 0.340125] pci 0000:00:1f.2: PME# supported from D3hot
> [ 0.340151] pci 0000:00:1f.3: [8086:1e22] type 00 class 0x0c0500
> [ 0.340174] pci 0000:00:1f.3: reg 10: [mem 0xf7c25000-0xf7c250ff 64bit]
> [ 0.340207] pci 0000:00:1f.3: reg 20: [io 0xf040-0xf05f]
> [ 0.340247] pci_bus 0000:00: on NUMA node 0
> [ 0.340252] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
> [ 0.340943] pci0000:00: Unable to request _OSC control (_OSC
> support mask: 0x19)
> [ 0.348050] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 10 *11 12 14 15)
> [ 0.348139] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 10 11 12
> 14 15) *0, disabled.
> [ 0.348234] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 10 11 12
> 14 15) *0, disabled.
> [ 0.348318] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 10 11 12
> 14 15) *0, disabled.
> [ 0.348400] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 10 *11 12 14 15)
> [ 0.348482] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 *10 11 12 14 15)
> [ 0.348565] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 10 *11 12 14 15)
> [ 0.348645] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 *10 11 12 14 15)
> [ 0.349002] SCSI subsystem initialized
> [ 0.349133] libata version 3.00 loaded.
> [ 0.349416] PCI: Using ACPI for IRQ routing
> [ 0.351780] PCI: pci_cache_line_size set to 64 bytes
> [ 0.351839] e820: reserve RAM buffer [mem 0x0009d800-0x0009ffff]
> [ 0.351843] e820: reserve RAM buffer [mem 0xd9cd4000-0xdbffffff]
> [ 0.351850] e820: reserve RAM buffer [mem 0xda304000-0xdbffffff]
> [ 0.351855] e820: reserve RAM buffer [mem 0xda753000-0xdbffffff]
> [ 0.351860] e820: reserve RAM buffer [mem 0xdadff000-0xdbffffff]
> [ 0.351864] e820: reserve RAM buffer [mem 0xdb000000-0xdbffffff]
> [ 0.352218] Switching to clocksource hpet
> [ 0.352310] pnp: PnP ACPI init
> [ 0.352318] ACPI: bus type pnp registered
> [ 0.352821] pnp 00:00: [bus 00-3e]
> [ 0.352825] pnp 00:00: [io 0x0000-0x0cf7 window]
> [ 0.352829] pnp 00:00: [io 0x0cf8-0x0cff]
> [ 0.352833] pnp 00:00: [io 0x0d00-0xffff window]
> [ 0.352839] pnp 00:00: [mem 0x000a0000-0x000bffff window]
> [ 0.352843] pnp 00:00: [mem 0x000c0000-0x000c3fff window]
> [ 0.352846] pnp 00:00: [mem 0x000c4000-0x000c7fff window]
> [ 0.352850] pnp 00:00: [mem 0x000c8000-0x000cbfff window]
> [ 0.352853] pnp 00:00: [mem 0x000cc000-0x000cffff window]
> [ 0.352857] pnp 00:00: [mem 0x000d0000-0x000d3fff window]
> [ 0.352860] pnp 00:00: [mem 0x000d4000-0x000d7fff window]
> [ 0.352864] pnp 00:00: [mem 0x000d8000-0x000dbfff window]
> [ 0.352867] pnp 00:00: [mem 0x000dc000-0x000dffff window]
> [ 0.352870] pnp 00:00: [mem 0x000e0000-0x000e3fff window]
> [ 0.352874] pnp 00:00: [mem 0x000e4000-0x000e7fff window]
> [ 0.352877] pnp 00:00: [mem 0x000e8000-0x000ebfff window]
> [ 0.352881] pnp 00:00: [mem 0x000ec000-0x000effff window]
> [ 0.352884] pnp 00:00: [mem 0x000f0000-0x000fffff window]
> [ 0.352888] pnp 00:00: [mem 0xdfa00000-0xfeafffff window]
> [ 0.352891] pnp 00:00: [mem 0x00010000-0x0001ffff window]
> [ 0.353014] pnp 00:00: Plug and Play ACPI device, IDs PNP0a08
> PNP0a03 (active)
> [ 0.353064] pnp 00:01: [mem 0xfed40000-0xfed44fff]
> [ 0.353151] system 00:01: [mem 0xfed40000-0xfed44fff] has been reserved
> [ 0.353156] system 00:01: Plug and Play ACPI device, IDs PNP0c01 (active)
> [ 0.353253] pnp 00:02: [io 0x0000-0x001f]
> [ 0.353256] pnp 00:02: [io 0x0081-0x0091]
> [ 0.353272] pnp 00:02: [io 0x0093-0x009f]
> [ 0.353275] pnp 00:02: [io 0x00c0-0x00df]
> [ 0.353279] pnp 00:02: [dma 4]
> [ 0.353346] pnp 00:02: Plug and Play ACPI device, IDs PNP0200 (active)
> [ 0.353361] pnp 00:03: [mem 0xff000000-0xffffffff]
> [ 0.353426] pnp 00:03: Plug and Play ACPI device, IDs INT0800 (active)
> [ 0.353549] pnp 00:04: [mem 0xfed00000-0xfed003ff]
> [ 0.353620] pnp 00:04: Plug and Play ACPI device, IDs PNP0103 (active)
> [ 0.353647] pnp 00:05: [io 0x002e-0x002f]
> [ 0.353651] pnp 00:05: [io 0x004e-0x004f]
> [ 0.353654] pnp 00:05: [io 0x0061]
> [ 0.353657] pnp 00:05: [io 0x0063]
> [ 0.353660] pnp 00:05: [io 0x0065]
> [ 0.353663] pnp 00:05: [io 0x0067]
> [ 0.353666] pnp 00:05: [io 0x0070]
> [ 0.353669] pnp 00:05: [io 0x0080]
> [ 0.353672] pnp 00:05: [io 0x0092]
> [ 0.353675] pnp 00:05: [io 0x00b2-0x00b3]
> [ 0.353678] pnp 00:05: [io 0x0680-0x069f]
> [ 0.353681] pnp 00:05: [io 0x1000-0x100f]
> [ 0.353684] pnp 00:05: [io 0xffff]
> [ 0.353687] pnp 00:05: [io 0xffff]
> [ 0.353690] pnp 00:05: [io 0x0400-0x0453]
> [ 0.353694] pnp 00:05: [io 0x0458-0x047f]
> [ 0.353697] pnp 00:05: [io 0x0500-0x057f]
> [ 0.353700] pnp 00:05: [io 0x164e-0x164f]
> [ 0.353800] system 00:05: [io 0x0680-0x069f] has been reserved
> [ 0.353804] system 00:05: [io 0x1000-0x100f] has been reserved
> [ 0.353808] system 00:05: [io 0xffff] has been reserved
> [ 0.353812] system 00:05: [io 0xffff] has been reserved
> [ 0.353816] system 00:05: [io 0x0400-0x0453] has been reserved
> [ 0.353820] system 00:05: [io 0x0458-0x047f] has been reserved
> [ 0.353827] system 00:05: [io 0x0500-0x057f] has been reserved
> [ 0.353831] system 00:05: [io 0x164e-0x164f] has been reserved
> [ 0.353836] system 00:05: Plug and Play ACPI device, IDs PNP0c02 (active)
> [ 0.353852] pnp 00:06: [io 0x0070-0x0077]
> [ 0.353863] pnp 00:06: [irq 8]
> [ 0.353934] pnp 00:06: Plug and Play ACPI device, IDs PNP0b00 (active)
> [ 0.353985] pnp 00:07: [io 0x0454-0x0457]
> [ 0.354069] system 00:07: [io 0x0454-0x0457] has been reserved
> [ 0.354075] system 00:07: Plug and Play ACPI device, IDs INT3f0d
> PNP0c02 (active)
> [ 0.375558] pnp 00:08: [io 0x0010-0x001f]
> [ 0.375562] pnp 00:08: [io 0x0022-0x003f]
> [ 0.375566] pnp 00:08: [io 0x0044-0x005f]
> [ 0.375569] pnp 00:08: [io 0x0072-0x007f]
> [ 0.375572] pnp 00:08: [io 0x0080]
> [ 0.375575] pnp 00:08: [io 0x0084-0x0086]
> [ 0.375578] pnp 00:08: [io 0x0088]
> [ 0.375581] pnp 00:08: [io 0x008c-0x008e]
> [ 0.375584] pnp 00:08: [io 0x0090-0x009f]
> [ 0.375587] pnp 00:08: [io 0x00a2-0x00bf]
> [ 0.375590] pnp 00:08: [io 0x00e0-0x00ef]
> [ 0.375593] pnp 00:08: [io 0x04d0-0x04d1]
> [ 0.375693] system 00:08: [io 0x04d0-0x04d1] has been reserved
> [ 0.375698] system 00:08: Plug and Play ACPI device, IDs PNP0c02 (active)
> [ 0.375716] pnp 00:09: [io 0x00f0-0x00ff]
> [ 0.375725] pnp 00:09: [irq 13]
> [ 0.375795] pnp 00:09: Plug and Play ACPI device, IDs PNP0c04 (active)
> [ 0.376163] pnp 00:0a: [mem 0xfed1c000-0xfed1ffff]
> [ 0.376167] pnp 00:0a: [mem 0xfed10000-0xfed17fff]
> [ 0.376170] pnp 00:0a: [mem 0xfed18000-0xfed18fff]
> [ 0.376174] pnp 00:0a: [mem 0xfed19000-0xfed19fff]
> [ 0.376177] pnp 00:0a: [mem 0xf8000000-0xfbffffff]
> [ 0.376180] pnp 00:0a: [mem 0xfed20000-0xfed3ffff]
> [ 0.376183] pnp 00:0a: [mem 0xfed90000-0xfed93fff]
> [ 0.376186] pnp 00:0a: [mem 0xfed45000-0xfed8ffff]
> [ 0.376190] pnp 00:0a: [mem 0xff000000-0xffffffff]
> [ 0.376193] pnp 00:0a: [mem 0xfee00000-0xfeefffff]
> [ 0.376196] pnp 00:0a: [mem 0xdfa00000-0xdfa00fff]
> [ 0.376302] system 00:0a: [mem 0xfed1c000-0xfed1ffff] has been reserved
> [ 0.376307] system 00:0a: [mem 0xfed10000-0xfed17fff] has been reserved
> [ 0.376311] system 00:0a: [mem 0xfed18000-0xfed18fff] has been reserved
> [ 0.376315] system 00:0a: [mem 0xfed19000-0xfed19fff] has been reserved
> [ 0.376319] system 00:0a: [mem 0xf8000000-0xfbffffff] has been reserved
> [ 0.376323] system 00:0a: [mem 0xfed20000-0xfed3ffff] has been reserved
> [ 0.376327] system 00:0a: [mem 0xfed90000-0xfed93fff] has been reserved
> [ 0.376331] system 00:0a: [mem 0xfed45000-0xfed8ffff] has been reserved
> [ 0.376335] system 00:0a: [mem 0xff000000-0xffffffff] has been reserved
> [ 0.376340] system 00:0a: [mem 0xfee00000-0xfeefffff] could not be reserved
> [ 0.376344] system 00:0a: [mem 0xdfa00000-0xdfa00fff] has been reserved
> [ 0.376348] system 00:0a: Plug and Play ACPI device, IDs PNP0c02 (active)
> [ 0.376615] pnp 00:0b: [mem 0x20000000-0x201fffff]
> [ 0.376619] pnp 00:0b: [mem 0x40000000-0x401fffff]
> [ 0.376731] system 00:0b: [mem 0x20000000-0x201fffff] has been reserved
> [ 0.376735] system 00:0b: [mem 0x40000000-0x401fffff] has been reserved
> [ 0.376740] system 00:0b: Plug and Play ACPI device, IDs PNP0c01 (active)
> [ 0.376788] pnp: PnP ACPI: found 12 devices
> [ 0.376790] ACPI: ACPI bus type pnp unregistered
> [ 0.380904] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
> [ 0.380908] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]
> [ 0.380912] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
> [ 0.380916] pci_bus 0000:00: resource 7 [mem 0x000d0000-0x000d3fff]
> [ 0.380919] pci_bus 0000:00: resource 8 [mem 0x000d4000-0x000d7fff]
> [ 0.380922] pci_bus 0000:00: resource 9 [mem 0x000d8000-0x000dbfff]
> [ 0.380926] pci_bus 0000:00: resource 10 [mem 0x000dc000-0x000dffff]
> [ 0.380930] pci_bus 0000:00: resource 11 [mem 0x000e0000-0x000e3fff]
> [ 0.380933] pci_bus 0000:00: resource 12 [mem 0x000e4000-0x000e7fff]
> [ 0.380937] pci_bus 0000:00: resource 13 [mem 0xdfa00000-0xfeafffff]
> [ 0.380983] NET: Registered protocol family 2
> [ 0.381053] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
> [ 0.381187] TCP established hash table entries: 131072 (order: 8,
> 1048576 bytes)
> [ 0.381661] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
> [ 0.381866] TCP: Hash tables configured (established 131072 bind 65536)
> [ 0.381869] TCP: reno registered
> [ 0.381873] UDP hash table entries: 512 (order: 2, 16384 bytes)
> [ 0.381882] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
> [ 0.381952] NET: Registered protocol family 1
> [ 0.381974] pci 0000:00:02.0: Boot video device
> [ 0.413296] PCI: CLS 64 bytes, default 64
> [ 0.413380] Unpacking initramfs...
> [ 1.467343] Freeing initrd memory: 25400k freed
> [ 1.474218] highmem bounce pool size: 64 pages
> [ 1.478699] fuse init (API version 7.19)
> [ 1.478903] msgmni has been set to 1705
> [ 1.479021] io scheduler noop registered (default)
> [ 1.479447] vesafb: mode is 640x480x32, linelength=2560, pages=0
> [ 1.479449] vesafb: scrolling: redraw
> [ 1.479453] vesafb: Truecolor: size=8:8:8:8, shift=24:16:8:0
> [ 1.479625] vesafb: framebuffer at 0xe0000000, mapped to
> 0xf8080000, using 1216k, total 1216k
> [ 1.523807] Console: switching to colour frame buffer device 80x30
> [ 1.562290] fb0: VESA VGA frame buffer device
> [ 1.566886] Monitor-Mwait will be used to enter C-1 state
> [ 1.567924] Monitor-Mwait will be used to enter C-2 state
> [ 1.567942] ACPI: acpi_idle registered with cpuidle
> [ 1.595068] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
> [ 1.615741] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
> [ 1.617473] loop: module loaded
> [ 1.617650] ahci 0000:00:1f.2: version 3.0
> [ 1.617728] ahci 0000:00:1f.2: irq 40 for MSI/MSI-X
> [ 1.628259] ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 6 ports 3
> Gbps 0x8 impl SATA mode
> [ 1.628267] ahci 0000:00:1f.2: flags: 64bit ncq pm led clo pio slum
> part ems apst
> [ 1.628275] ahci 0000:00:1f.2: setting latency timer to 64
> [ 1.629288] scsi0 : ahci
> [ 1.629439] scsi1 : ahci
> [ 1.629567] scsi2 : ahci
> [ 1.629692] scsi3 : ahci
> [ 1.629818] scsi4 : ahci
> [ 1.629944] scsi5 : ahci
> [ 1.630497] ata1: DUMMY
> [ 1.630500] ata2: DUMMY
> [ 1.630502] ata3: DUMMY
> [ 1.630505] ata4: SATA max UDMA/133 abar m2048 at 0xf7c26000 port
> 0xf7c26280 irq 40
> [ 1.630508] ata5: DUMMY
> [ 1.630510] ata6: DUMMY
> [ 1.630904] e100: Intel(R) PRO/100 Network Driver, 3.5.24-k2-NAPI
> [ 1.630906] e100: Copyright(c) 1999-2006 Intel Corporation
> [ 1.630954] e1000e: Intel(R) PRO/1000 Network Driver - 2.0.0-k
> [ 1.630956] e1000e: Copyright(c) 1999 - 2012 Intel Corporation.
> [ 1.630990] e1000e 0000:00:19.0: setting latency timer to 64
> [ 1.631070] e1000e 0000:00:19.0: (unregistered net_device):
> Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode
> [ 1.631113] e1000e 0000:00:19.0: irq 41 for MSI/MSI-X
> [ 1.880531] e1000e 0000:00:19.0: eth0: (PCI Express:2.5GT/s:Width
> x1) 00:30:d6:08:96:48
> [ 1.880537] e1000e 0000:00:19.0: eth0: Intel(R) PRO/1000 Network Connection
> [ 1.880573] e1000e 0000:00:19.0: eth0: MAC: 10, PHY: 11, PBA No: FFFFFF-0FF
> [ 1.880758] rtc_cmos 00:06: RTC can wake from S4
> [ 1.880921] rtc_cmos 00:06: rtc core: registered rtc_cmos as rtc0
> [ 1.880955] rtc0: alarms up to one month, y3k, 242 bytes nvram, hpet irqs
> [ 1.880994] i2c /dev entries driver
> [ 1.881124] cpuidle: using governor ladder
> [ 1.881216] TCP: cubic registered
> [ 1.881230] NET: Registered protocol family 17
> [ 1.881247] Key type dns_resolver registered
> [ 1.881315] Using IPI Shortcut mode
> [ 1.935273] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
> [ 1.937011] ata4.00: ACPI cmd ef/10:06:00:00:00:00 (SET FEATURES)
> rejected by device (Stat=0x51 Err=0x04)
> [ 1.937022] ata4.00: ACPI cmd f5/00:00:00:00:00:00 (SECURITY FREEZE
> LOCK) filtered out
> [ 1.937028] ata4.00: ACPI cmd b1/c1:00:00:00:00:00 (DEVICE
> CONFIGURATION OVERLAY) filtered out
> [ 1.937049] ata4.00: ATA-8: 4GB SATA Flash Drive, SFI2101D, max UDMA/133
> [ 1.937053] ata4.00: 7719264 sectors, multi 1: LBA48
> [ 1.938832] ata4.00: ACPI cmd ef/10:06:00:00:00:00 (SET FEATURES)
> rejected by device (Stat=0x51 Err=0x04)
> [ 1.938854] ata4.00: ACPI cmd f5/00:00:00:00:00:00 (SECURITY FREEZE
> LOCK) filtered out
> [ 1.938858] ata4.00: ACPI cmd b1/c1:00:00:00:00:00 (DEVICE
> CONFIGURATION OVERLAY) filtered out
> [ 1.938866] ata4.00: configured for UDMA/133
> [ 1.939100] scsi 3:0:0:0: Direct-Access ATA 4GB SATA Flash
> D SFI2 PQ: 0 ANSI: 5
> [ 1.939648] sd 3:0:0:0: [sda] 7719264 512-byte logical blocks:
> (3.95 GB/3.68 GiB)
> [ 1.939810] Freeing unused kernel memory: 320k freed
> [ 1.939980] Write protecting the kernel text: 2800k
> [ 1.940014] Write protecting the kernel read-only data: 1048k
> [ 1.940093] sd 3:0:0:0: [sda] Write Protect is off
> [ 1.940098] sd 3:0:0:0: [sda] Mode Sense: 00 3a 00 00
> [ 1.940125] sd 3:0:0:0: [sda] Write cache: enabled, read cache:
> enabled, doesn't support DPO or FUA
> [ 1.941783] sda: sda1 sda2
> [ 1.942375] sd 3:0:0:0: [sda] Attached SCSI disk
> [ 1.960567] udev[1105]: starting version 164
> [ 2.003652] Linux agpgart interface v0.103
> [ 2.007357] input: Power Button as
> /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input0
> [ 2.024315] ACPI: bus type usb registered
> [ 2.024367] usbcore: registered new interface driver usbfs
> [ 2.024386] usbcore: registered new interface driver hub
> [ 2.025014] agpgart-intel 0000:00:00.0: Intel Sandybridge Chipset
> [ 2.025105] agpgart-intel 0000:00:00.0: detected gtt size: 2097152K
> total, 262144K mappable
> [ 2.026044] agpgart-intel 0000:00:00.0: detected 65536K stolen memory
> [ 2.032627] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xe0000000
> [ 2.032677] usbcore: registered new device driver usb
> [ 2.033440] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
> [ 2.033499] ehci_hcd 0000:00:1a.0: setting latency timer to 64
> [ 2.033505] ehci_hcd 0000:00:1a.0: EHCI Host Controller
> [ 2.033517] ehci_hcd 0000:00:1a.0: new USB bus registered, assigned
> bus number 1
> [ 2.033548] ehci_hcd 0000:00:1a.0: debug port 2
> [ 2.037286] ACPI: Power Button [PWRB]
> [ 2.037378] input: Lid Switch as
> /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input1
> [ 2.039055] ACPI: Lid Switch [LID0]
> [ 2.039130] input: Sleep Button as
> /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input2
> [ 2.040956] ACPI: Sleep Button [SLPB]
> [ 2.041041] input: Power Button as
> /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
> [ 2.041443] ACPI: Power Button [PWRF]
> [ 2.048419] ehci_hcd 0000:00:1a.0: cache line size of 64 is not supported
> [ 2.048453] ehci_hcd 0000:00:1a.0: irq 21, io mem 0xf7c28000
> [ 2.054255] ehci_hcd 0000:00:1a.0: USB 2.0 started, EHCI 1.00
> [ 2.055233] hub 1-0:1.0: USB hub found
> [ 2.055242] hub 1-0:1.0: 2 ports detected
> [ 2.055354] ehci_hcd 0000:00:1d.0: setting latency timer to 64
> [ 2.055360] ehci_hcd 0000:00:1d.0: EHCI Host Controller
> [ 2.055369] ehci_hcd 0000:00:1d.0: new USB bus registered, assigned
> bus number 2
> [ 2.055400] ehci_hcd 0000:00:1d.0: debug port 2
> [ 2.064084] ehci_hcd 0000:00:1d.0: cache line size of 64 is not supported
> [ 2.064118] ehci_hcd 0000:00:1d.0: irq 23, io mem 0xf7c27000
> [ 2.069241] ehci_hcd 0000:00:1d.0: USB 2.0 started, EHCI 1.00
> [ 2.070089] hub 2-0:1.0: USB hub found
> [ 2.070098] hub 2-0:1.0: 2 ports detected
> [ 2.133599] [drm] Initialized drm 1.1.0 20060810
> [ 2.142163] checking generic (e0000000 130000) vs hw (e0000000 10000000)
> [ 2.142169] fb: conflicting fb hw usage inteldrmfb vs VESA VGA -
> removing generic driver
> [ 2.142179] i915 0000:00:02.0: setting latency timer to 64
> [ 2.143064] i915 0000:00:02.0: irq 42 for MSI/MSI-X
> [ 2.143078] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
> [ 2.143081] [drm] Driver supports precise vblank timestamp query.
> [ 2.357276] usb 1-1: new high-speed USB device number 2 using ehci_hcd
> [ 2.472022] hub 1-1:1.0: USB hub found
> [ 2.472156] hub 1-1:1.0: 6 ports detected
> [ 2.475222] Refined TSC clocksource calibration: 1097.506 MHz.
> [ 2.475230] Switching to clocksource tsc
> [ 2.568938] [drm] Enabling RC6 states: RC6 on, RC6p off, RC6pp off
> [ 2.576234] usb 2-1: new high-speed USB device number 2 using ehci_hcd
> [ 2.687418] checking generic (e0000000 130000) vs hw (e0000000 10000000)
> [ 2.687424] fb: conflicting fb hw usage inteldrmfb vs VESA VGA -
> removing generic driver
> [ 2.687604] fbcon: inteldrmfb (fb1) is primary device
> [ 2.687610] fbcon: Remapping primary device, fb1, to tty 1-63
> [ 2.691079] hub 2-1:1.0: USB hub found
> [ 2.691239] hub 2-1:1.0: 6 ports detected
> [ 2.967421] usb 2-1.2: new low-speed USB device number 3 using ehci_hcd
> [ 3.056618] usbcore: registered new interface driver usbhid
> [ 3.056620] usbhid: USB HID core driver
> [ 10.308019] fb1: inteldrmfb frame buffer device
> [ 10.308022] drm: registered panic notifier
> [ 10.310228] acpi device:49: registered as cooling_device2
> [ 10.310507] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no)
> [ 10.310579] input: Video Bus as
> /devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:00/input/input4
> [ 10.310671] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
> [ 11.239942] EXT3-fs (sda2): recovery required on readonly filesystem
> [ 11.239950] EXT3-fs (sda2): write access will be enabled during recovery
> [ 12.024127] kjournald starting. Commit interval 5 seconds
> [ 12.026491] EXT3-fs (sda2): recovery complete
> [ 12.026499] EXT3-fs (sda2): mounted filesystem with ordered data mode
> [ 12.253989] udev[1326]: starting version 164
> [ 12.432057] input: Logitech USB-PS/2 Optical Mouse as
> /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.2/2-1.2:1.0/input/input5
> [ 12.432128] hid-generic 0003:046D:C03E.0001: input: USB HID v1.10
> Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:1d.0-1.2/input0
> [ 12.655841] EXT3-fs (sda2): using internal journal
> [ 13.118473] kjournald starting. Commit interval 5 seconds
> [ 13.118594] EXT3-fs (sda1): using internal journal
> [ 13.118598] EXT3-fs (sda1): mounted filesystem with ordered data mode
> [ 13.489211] e1000e 0000:00:19.0: irq 41 for MSI/MSI-X
> [ 13.590022] e1000e 0000:00:19.0: irq 41 for MSI/MSI-X
> [ 13.622888] sshd (2013): /proc/2013/oom_adj is deprecated, please
> use /proc/2013/oom_score_adj instead.
> [ 17.184440] e1000e: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow
> Control: Rx/Tx
> [ 56.001074] usb 2-1.4: new low-speed USB device number 4 using ehci_hcd
> [ 56.094540] input: HID 046a:0001 as
> /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.4/2-1.4:1.0/input/input6
> [ 56.094639] hid-generic 0003:046A:0001.0002: input: USB HID v1.00
> Keyboard [HID 046a:0001] on usb-0000:00:1d.0-1.4/input0
>
>
>
>
> root at OT:~# cat /var/log/Xorg.0.log
> [ 13.551]
> X.Org X Server 1.10.4
> Release Date: 2011-08-19
> [ 13.551] X Protocol Version 11, Revision 0
> [ 13.551] Build Operating System: Linux 2.6.32-5-amd64 i686 Debian
> [ 13.551] Current Operating System: Linux OT 3.5.3-bachmann #2 SMP
> PREEMPT Mon Aug 27 13:25:26 CEST 2012 i686
> [ 13.551] Kernel command line:
> BOOT_IMAGE=/boot/vmlinuz-3.5.3-bachmann root=/dev/sda2 ro rootwait
> splash vga=0x312 quiet
> [ 13.552] Build Date: 29 August 2011 12:12:25AM
> [ 13.552] xorg-server 2:1.10.4-1~bpo60+1 (Cyril Brulebois <kibi at debian.org>)
> [ 13.552] Current version of pixman: 0.24.0
> [ 13.552] Before reporting problems, check http://wiki.x.org
> to make sure that you have the latest version.
> [ 13.552] Markers: (--) probed, (**) from config file, (==) default setting,
> (++) from command line, (!!) notice, (II) informational,
> (WW) warning, (EE) error, (NI) not implemented, (??) unknown.
> [ 13.552] (==) Log file: "/var/log/Xorg.0.log", Time: Sun Jan 1
> 00:00:21 2012
> [ 13.554] (==) Using system config directory "/usr/share/X11/xorg.conf.d"
> [ 13.555] (==) No Layout section. Using the first Screen section.
> [ 13.555] (==) No screen section available. Using defaults.
> [ 13.555] (**) |-->Screen "Default Screen Section" (0)
> [ 13.555] (**) | |-->Monitor "<default monitor>"
> [ 13.557] (==) No monitor specified for screen "Default Screen Section".
> Using a default monitor configuration.
> [ 13.557] (==) Automatically adding devices
> [ 13.557] (==) Automatically enabling devices
> [ 13.559] (WW) The directory "/usr/share/fonts/X11/cyrillic" does not exist.
> [ 13.559] Entry deleted from font path.
> [ 13.562] (WW) The directory
> "/var/lib/defoma/x-ttcidfont-conf.d/dirs/TrueType" does not exist.
> [ 13.562] Entry deleted from font path.
> [ 13.562] (==) FontPath set to:
> /usr/share/fonts/X11/misc,
> /usr/share/fonts/X11/100dpi/:unscaled,
> /usr/share/fonts/X11/75dpi/:unscaled,
> /usr/share/fonts/X11/Type1,
> /usr/share/fonts/X11/100dpi,
> /usr/share/fonts/X11/75dpi,
> built-ins
> [ 13.562] (==) ModulePath set to "/usr/lib/xorg/modules"
> [ 13.562] (II) The server relies on udev to provide the list of
> input devices.
> If no devices become available, reconfigure udev or disable
> AutoAddDevices.
> [ 13.562] (II) Loader magic: 0x81fa6c0
> [ 13.562] (II) Module ABI versions:
> [ 13.562] X.Org ANSI C Emulation: 0.4
> [ 13.562] X.Org Video Driver: 10.0
> [ 13.562] X.Org XInput driver : 12.2
> [ 13.562] X.Org Server Extension : 5.0
> [ 13.562] (--) PCI:*(0:0:2:0) 8086:0106:8086:2010 rev 9, Mem @
> 0xf7800000/4194304, 0xe0000000/268435456, I/O @ 0x0000f000/64
> [ 13.562] (WW) Open ACPI failed (/var/run/acpid.socket) (No such
> file or directory)
> [ 13.562] (II) LoadModule: "extmod"
> [ 13.568] (II) Loading /usr/lib/xorg/modules/extensions/libextmod.so
> [ 13.570] (II) Module extmod: vendor="X.Org Foundation"
> [ 13.570] compiled for 1.10.4, module version = 1.0.0
> [ 13.570] Module class: X.Org Server Extension
> [ 13.570] ABI class: X.Org Server Extension, version 5.0
> [ 13.570] (II) Loading extension SELinux
> [ 13.570] (II) Loading extension MIT-SCREEN-SAVER
> [ 13.570] (II) Loading extension XFree86-VidModeExtension
> [ 13.570] (II) Loading extension XFree86-DGA
> [ 13.570] (II) Loading extension DPMS
> [ 13.570] (II) Loading extension XVideo
> [ 13.570] (II) Loading extension XVideo-MotionCompensation
> [ 13.570] (II) Loading extension X-Resource
> [ 13.570] (II) LoadModule: "dbe"
> [ 13.571] (II) Loading /usr/lib/xorg/modules/extensions/libdbe.so
> [ 13.571] (II) Module dbe: vendor="X.Org Foundation"
> [ 13.571] compiled for 1.10.4, module version = 1.0.0
> [ 13.571] Module class: X.Org Server Extension
> [ 13.571] ABI class: X.Org Server Extension, version 5.0
> [ 13.571] (II) Loading extension DOUBLE-BUFFER
> [ 13.571] (II) LoadModule: "glx"
> [ 13.571] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
> [ 13.573] (II) Module glx: vendor="X.Org Foundation"
> [ 13.573] compiled for 1.10.4, module version = 1.0.0
> [ 13.573] ABI class: X.Org Server Extension, version 5.0
> [ 13.576] (==) AIGLX enabled
> [ 13.576] (II) Loading extension GLX
> [ 13.576] (II) LoadModule: "record"
> [ 13.576] (II) Loading /usr/lib/xorg/modules/extensions/librecord.so
> [ 13.576] (II) Module record: vendor="X.Org Foundation"
> [ 13.576] compiled for 1.10.4, module version = 1.13.0
> [ 13.577] Module class: X.Org Server Extension
> [ 13.577] ABI class: X.Org Server Extension, version 5.0
> [ 13.577] (II) Loading extension RECORD
> [ 13.577] (II) LoadModule: "dri"
> [ 13.577] (II) Loading /usr/lib/xorg/modules/extensions/libdri.so
> [ 13.579] (II) Module dri: vendor="X.Org Foundation"
> [ 13.579] compiled for 1.10.4, module version = 1.0.0
> [ 13.580] ABI class: X.Org Server Extension, version 5.0
> [ 13.580] (II) Loading extension XFree86-DRI
> [ 13.580] (II) LoadModule: "dri2"
> [ 13.580] (II) Loading /usr/lib/xorg/modules/extensions/libdri2.so
> [ 13.581] (II) Module dri2: vendor="X.Org Foundation"
> [ 13.581] compiled for 1.10.4, module version = 1.2.0
> [ 13.581] ABI class: X.Org Server Extension, version 5.0
> [ 13.581] (II) Loading extension DRI2
> [ 13.581] (==) Matched intel as autoconfigured driver 0
> [ 13.581] (==) Matched vesa as autoconfigured driver 1
> [ 13.581] (==) Matched fbdev as autoconfigured driver 2
> [ 13.581] (==) Assigned the driver to the xf86ConfigLayout
> [ 13.581] (II) LoadModule: "intel"
> [ 13.581] (II) Loading /usr/lib/xorg/modules/drivers/intel_drv.so
> [ 13.590] (II) Module intel: vendor="X.Org Foundation"
> [ 13.590] compiled for 1.10.4, module version = 2.20.5
> [ 13.590] Module class: X.Org Video Driver
> [ 13.590] ABI class: X.Org Video Driver, version 10.0
> [ 13.590] (II) LoadModule: "vesa"
> [ 13.590] (II) Loading /usr/lib/xorg/modules/drivers/vesa_drv.so
> [ 13.591] (II) Module vesa: vendor="X.Org Foundation"
> [ 13.591] compiled for 1.10.3, module version = 2.3.0
> [ 13.591] Module class: X.Org Video Driver
> [ 13.591] ABI class: X.Org Video Driver, version 10.0
> [ 13.591] (II) LoadModule: "fbdev"
> [ 13.591] (II) Loading /usr/lib/xorg/modules/drivers/fbdev_drv.so
> [ 13.592] (II) Module fbdev: vendor="X.Org Foundation"
> [ 13.592] compiled for 1.10.3, module version = 0.4.2
> [ 13.592] ABI class: X.Org Video Driver, version 10.0
> [ 13.592] (II) intel: Driver for Intel Integrated Graphics Chipsets: i810,
> i810-dc100, i810e, i815, i830M, 845G, 854, 852GM/855GM, 865G, 915G,
> E7221 (i915), 915GM, 945G, 945GM, 945GME, Pineview GM, Pineview G,
> 965G, G35, 965Q, 946GZ, 965GM, 965GME/GLE, G33, Q35, Q33, GM45,
> 4 Series, G45/G43, Q45/Q43, G41, B43, B43, Clarkdale, Arrandale,
> Sandybridge Desktop (GT1), Sandybridge Desktop (GT2),
> Sandybridge Desktop (GT2+), Sandybridge Mobile (GT1),
> Sandybridge Mobile (GT2), Sandybridge Mobile (GT2+),
> Sandybridge Server, Ivybridge Mobile (GT1), Ivybridge Mobile (GT2),
> Ivybridge Desktop (GT1), Ivybridge Desktop (GT2), Ivybridge Server,
> Ivybridge Server (GT2), Haswell Desktop (GT1), Haswell Desktop (GT2),
> Haswell Desktop (GT2+), Haswell Mobile (GT1), Haswell Mobile (GT2),
> Haswell Mobile (GT2+), Haswell Server (GT1), Haswell Server (GT2),
> Haswell Server (GT2+), Haswell SDV Desktop (GT1),
> Haswell SDV Desktop (GT2), Haswell SDV Desktop (GT2+),
> Haswell SDV Mobile (GT1), Haswell SDV Mobile (GT2),
> Haswell SDV Mobile (GT2+), Haswell SDV Server (GT1),
> Haswell SDV Server (GT2), Haswell SDV Server (GT2+),
> Haswell ULT Desktop (GT1), Haswell ULT Desktop (GT2),
> Haswell ULT Desktop (GT2+), Haswell ULT Mobile (GT1),
> Haswell ULT Mobile (GT2), Haswell ULT Mobile (GT2+),
> Haswell ULT Server (GT1), Haswell ULT Server (GT2),
> Haswell ULT Server (GT2+), Haswell CRW Desktop (GT1),
> Haswell CRW Desktop (GT2), Haswell CRW Desktop (GT2+),
> Haswell CRW Mobile (GT1), Haswell CRW Mobile (GT2),
> Haswell CRW Mobile (GT2+), Haswell CRW Server (GT1),
> Haswell CRW Server (GT2), Haswell CRW Server (GT2+)
> [ 13.593] (II) VESA: driver for VESA chipsets: vesa
> [ 13.593] (II) FBDEV: driver for framebuffer: fbdev
> [ 13.593] (--) using VT number 2
>
> [ 13.840] drmOpenDevice: node name is /dev/dri/card0
> [ 13.840] drmOpenDevice: open result is 7, (OK)
> [ 13.840] drmOpenByBusid: Searching for BusID pci:0000:00:02.0
> [ 13.840] drmOpenDevice: node name is /dev/dri/card0
> [ 13.840] drmOpenDevice: open result is 7, (OK)
> [ 13.840] drmOpenByBusid: drmOpenMinor returns 7
> [ 13.840] drmOpenByBusid: Interface 1.4 failed, trying 1.1
> [ 13.840] drmOpenByBusid: drmGetBusid reports
> [ 13.840] drmOpenDevice: node name is /dev/dri/card1
> [ 13.840] drmOpenDevice: open result is -1, (No such device)
> [ 13.840] drmOpenDevice: open result is -1, (No such device)
> [ 13.840] drmOpenDevice: Open failed
> [ 13.840] drmOpenByBusid: drmOpenMinor returns -19
> [ 13.840] drmOpenDevice: node name is /dev/dri/card2
> [ 13.840] drmOpenDevice: open result is -1, (No such device)
> [ 13.840] drmOpenDevice: open result is -1, (No such device)
> [ 13.840] drmOpenDevice: Open failed
> [ 13.840] drmOpenByBusid: drmOpenMinor returns -19
> [ 13.840] drmOpenDevice: node name is /dev/dri/card3
> [ 13.840] drmOpenDevice: open result is -1, (No such device)
> [ 13.840] drmOpenDevice: open result is -1, (No such device)
> [ 13.840] drmOpenDevice: Open failed
> [ 13.840] drmOpenByBusid: drmOpenMinor returns -19
> [ 13.840] drmOpenDevice: node name is /dev/dri/card4
> [ 13.840] drmOpenDevice: open result is -1, (No such device)
> [ 13.840] drmOpenDevice: open result is -1, (No such device)
> [ 13.840] drmOpenDevice: Open failed
> [ 13.840] drmOpenByBusid: drmOpenMinor returns -19
> [ 13.840] drmOpenDevice: node name is /dev/dri/card5
> [ 13.840] drmOpenDevice: open result is -1, (No such device)
> [ 13.841] drmOpenDevice: open result is -1, (No such device)
> [ 13.841] drmOpenDevice: Open failed
> [ 13.841] drmOpenByBusid: drmOpenMinor returns -19
> [ 13.841] drmOpenDevice: node name is /dev/dri/card6
> [ 13.841] drmOpenDevice: open result is -1, (No such device)
> [ 13.841] drmOpenDevice: open result is -1, (No such device)
> [ 13.841] drmOpenDevice: Open failed
> [ 13.841] drmOpenByBusid: drmOpenMinor returns -19
> [ 13.841] drmOpenDevice: node name is /dev/dri/card7
> [ 13.841] drmOpenDevice: open result is -1, (No such device)
> [ 13.841] drmOpenDevice: open result is -1, (No such device)
> [ 13.841] drmOpenDevice: Open failed
> [ 13.841] drmOpenByBusid: drmOpenMinor returns -19
> [ 13.841] drmOpenDevice: node name is /dev/dri/card8
> [ 13.841] drmOpenDevice: open result is -1, (No such device)
> [ 13.841] drmOpenDevice: open result is -1, (No such device)
> [ 13.841] drmOpenDevice: Open failed
> [ 13.841] drmOpenByBusid: drmOpenMinor returns -19
> [ 13.841] drmOpenDevice: node name is /dev/dri/card9
> [ 13.841] drmOpenDevice: open result is -1, (No such device)
> [ 13.841] drmOpenDevice: open result is -1, (No such device)
> [ 13.841] drmOpenDevice: Open failed
> [ 13.841] drmOpenByBusid: drmOpenMinor returns -19
> [ 13.841] drmOpenDevice: node name is /dev/dri/card10
> [ 13.841] drmOpenDevice: open result is -1, (No such device)
> [ 13.841] drmOpenDevice: open result is -1, (No such device)
> [ 13.841] drmOpenDevice: Open failed
> [ 13.841] drmOpenByBusid: drmOpenMinor returns -19
> [ 13.841] drmOpenDevice: node name is /dev/dri/card11
> [ 13.841] drmOpenDevice: open result is -1, (No such device)
> [ 13.841] drmOpenDevice: open result is -1, (No such device)
> [ 13.841] drmOpenDevice: Open failed
> [ 13.841] drmOpenByBusid: drmOpenMinor returns -19
> [ 13.841] drmOpenDevice: node name is /dev/dri/card12
> [ 13.841] drmOpenDevice: open result is -1, (No such device)
> [ 13.841] drmOpenDevice: open result is -1, (No such device)
> [ 13.841] drmOpenDevice: Open failed
> [ 13.841] drmOpenByBusid: drmOpenMinor returns -19
> [ 13.841] drmOpenDevice: node name is /dev/dri/card13
> [ 13.842] drmOpenDevice: open result is -1, (No such device)
> [ 13.842] drmOpenDevice: open result is -1, (No such device)
> [ 13.842] drmOpenDevice: Open failed
> [ 13.842] drmOpenByBusid: drmOpenMinor returns -19
> [ 13.842] drmOpenDevice: node name is /dev/dri/card14
> [ 13.842] drmOpenDevice: open result is -1, (No such device)
> [ 13.842] drmOpenDevice: open result is -1, (No such device)
> [ 13.842] drmOpenDevice: Open failed
> [ 13.842] drmOpenByBusid: drmOpenMinor returns -19
> [ 13.842] drmOpenDevice: node name is /dev/dri/card15
> [ 13.842] drmOpenDevice: open result is -1, (No such device)
> [ 13.842] drmOpenDevice: open result is -1, (No such device)
> [ 13.842] drmOpenDevice: Open failed
> [ 13.842] drmOpenByBusid: drmOpenMinor returns -19
> [ 13.842] (II) Loading /usr/lib/xorg/modules/drivers/vesa_drv.so
> [ 13.842] vesa: Ignoring device with a bound kernel driver
> [ 13.842] (WW) Falling back to old probe method for vesa
> [ 13.842] (II) Loading sub module "fbdevhw"
> [ 13.842] (II) LoadModule: "fbdevhw"
> [ 13.842] (II) Loading /usr/lib/xorg/modules/libfbdevhw.so
> [ 13.843] (II) Module fbdevhw: vendor="X.Org Foundation"
> [ 13.843] compiled for 1.10.4, module version = 0.0.2
> [ 13.843] ABI class: X.Org Video Driver, version 10.0
> [ 13.843] (II) Loading /usr/lib/xorg/modules/drivers/fbdev_drv.so
> [ 13.843] (II) Loading /usr/lib/xorg/modules/libfbdevhw.so
> [ 13.843] (**) FBDEV(1): claimed PCI slot 0 at 0:2:0
> [ 13.843] (II) FBDEV(1): using default device
> [ 13.843] (WW) VGA arbiter: cannot open kernel arbiter, no multi-card support
> [ 13.843] (II) FBDEV(1): Creating default Display subsection in
> Screen section
> "Default Screen Section" for depth/fbbpp 24/32
> [ 13.843] (==) FBDEV(1): Depth 24, (==) framebuffer bpp 32
> [ 13.843] (==) FBDEV(1): RGB weight 888
> [ 13.843] (==) FBDEV(1): Default visual is TrueColor
> [ 13.843] (==) FBDEV(1): Using gamma correction (1.0, 1.0, 1.0)
> [ 13.843] (II) FBDEV(1): hardware: VESA VGA (video memory: 1216kB)
> [ 13.843] (II) FBDEV(1): checking modes against framebuffer device...
> [ 13.843] (II) FBDEV(1): checking modes against monitor...
> [ 13.843] (--) FBDEV(1): Virtual size is 640x480 (pitch 640)
> [ 13.843] (**) FBDEV(1): Built-in mode "current": 30.7 MHz, 36.9
> kHz, 73.3 Hz
> [ 13.844] (II) FBDEV(1): Modeline "current"x0.0 30.72 640 672
> 752 832 480 484 488 504 -hsync -vsync -csync (36.9 kHz)
> [ 13.844] (==) FBDEV(1): DPI set to (96, 96)
> [ 13.844] (II) Loading sub module "fb"
> [ 13.844] (II) LoadModule: "fb"
> [ 13.845] (II) Loading /usr/lib/xorg/modules/libfb.so
> [ 13.847] (II) Module fb: vendor="X.Org Foundation"
> [ 13.847] compiled for 1.10.4, module version = 1.0.0
> [ 13.847] ABI class: X.Org ANSI C Emulation, version 0.4
> [ 13.847] (**) FBDEV(1): using shadow framebuffer
> [ 13.847] (II) Loading sub module "shadow"
> [ 13.847] (II) LoadModule: "shadow"
> [ 13.847] (II) Loading /usr/lib/xorg/modules/libshadow.so
> [ 13.848] (II) Module shadow: vendor="X.Org Foundation"
> [ 13.848] compiled for 1.10.4, module version = 1.1.0
> [ 13.848] ABI class: X.Org ANSI C Emulation, version 0.4
> [ 13.848] (II) UnloadModule: "vesa"
> [ 13.848] (II) Unloading vesa
> [ 13.848] (==) Depth 24 pixmap format is 32 bpp
> [ 13.848] (EE) FBDEV(0): FBIOBLANK: Invalid argument
> [ 13.851] (==) FBDEV(0): Backing store disabled
> [ 13.852] (==) FBDEV(0): DPMS enabled
> [ 13.852] (==) RandR enabled
> [ 13.852] (II) Initializing built-in extension Generic Event Extension
> [ 13.852] (II) Initializing built-in extension SHAPE
> [ 13.852] (II) Initializing built-in extension MIT-SHM
> [ 13.852] (II) Initializing built-in extension XInputExtension
> [ 13.852] (II) Initializing built-in extension XTEST
> [ 13.852] (II) Initializing built-in extension BIG-REQUESTS
> [ 13.852] (II) Initializing built-in extension SYNC
> [ 13.852] (II) Initializing built-in extension XKEYBOARD
> [ 13.852] (II) Initializing built-in extension XC-MISC
> [ 13.852] (II) Initializing built-in extension SECURITY
> [ 13.852] (II) Initializing built-in extension XINERAMA
> [ 13.852] (II) Initializing built-in extension XFIXES
> [ 13.852] (II) Initializing built-in extension RENDER
> [ 13.852] (II) Initializing built-in extension RANDR
> [ 13.852] (II) Initializing built-in extension COMPOSITE
> [ 13.852] (II) Initializing built-in extension DAMAGE
> [ 13.853] (II) SELinux: Disabled on system
> [ 13.869] (II) AIGLX: Screen 0 is not DRI2 capable
> [ 13.870] (II) AIGLX: Screen 0 is not DRI capable
> [ 13.886] (II) AIGLX: Loaded and initialized /usr/lib/dri/swrast_dri.so
> [ 13.886] (II) GLX: Initialized DRISWRAST GL provider for screen 0
> [ 13.999] (II) config/udev: Adding input device Power Button
> (/dev/input/event3)
> [ 13.999] (**) Power Button: Applying InputClass "evdev keyboard catchall"
> [ 13.999] (II) LoadModule: "evdev"
> [ 14.001] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
> [ 14.002] (II) Module evdev: vendor="X.Org Foundation"
> [ 14.002] compiled for 1.10.3, module version = 2.6.0
> [ 14.002] Module class: X.Org XInput Driver
> [ 14.002] ABI class: X.Org XInput driver, version 12.2
> [ 14.002] (II) Using input driver 'evdev' for 'Power Button'
> [ 14.002] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
> [ 14.002] (**) Power Button: always reports core events
> [ 14.002] (**) Power Button: Device: "/dev/input/event3"
> [ 14.002] (--) Power Button: Found keys
> [ 14.002] (II) Power Button: Configuring as keyboard
> [ 14.002] (**) Option "config_info"
> "udev:/sys/devices/LNXSYSTM:00/LNXPWRBN:00/input/input3/event3"
> [ 14.002] (II) XINPUT: Adding extended input device "Power Button"
> (type: KEYBOARD)
> [ 14.002] (**) Option "xkb_rules" "evdev"
> [ 14.002] (**) Option "xkb_model" "pc105"
> [ 14.002] (**) Option "xkb_layout" "us"
> [ 14.003] (II) config/udev: Adding input device Video Bus (/dev/input/event4)
> [ 14.003] (**) Video Bus: Applying InputClass "evdev keyboard catchall"
> [ 14.003] (II) Using input driver 'evdev' for 'Video Bus'
> [ 14.003] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
> [ 14.003] (**) Video Bus: always reports core events
> [ 14.003] (**) Video Bus: Device: "/dev/input/event4"
> [ 14.003] (--) Video Bus: Found keys
> [ 14.003] (II) Video Bus: Configuring as keyboard
> [ 14.004] (**) Option "config_info"
> "udev:/sys/devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:00/input/input4/event4"
> [ 14.004] (II) XINPUT: Adding extended input device "Video Bus"
> (type: KEYBOARD)
> [ 14.004] (**) Option "xkb_rules" "evdev"
> [ 14.004] (**) Option "xkb_model" "pc105"
> [ 14.004] (**) Option "xkb_layout" "us"
> [ 14.008] (II) config/udev: Adding input device Power Button
> (/dev/input/event0)
> [ 14.008] (**) Power Button: Applying InputClass "evdev keyboard catchall"
> [ 14.008] (II) Using input driver 'evdev' for 'Power Button'
> [ 14.008] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
> [ 14.008] (**) Power Button: always reports core events
> [ 14.008] (**) Power Button: Device: "/dev/input/event0"
> [ 14.008] (--) Power Button: Found keys
> [ 14.008] (II) Power Button: Configuring as keyboard
> [ 14.008] (**) Option "config_info"
> "udev:/sys/devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input0/event0"
> [ 14.008] (II) XINPUT: Adding extended input device "Power Button"
> (type: KEYBOARD)
> [ 14.008] (**) Option "xkb_rules" "evdev"
> [ 14.008] (**) Option "xkb_model" "pc105"
> [ 14.008] (**) Option "xkb_layout" "us"
> [ 14.009] (II) config/udev: Adding input device Lid Switch
> (/dev/input/event1)
> [ 14.009] (II) No input driver/identifier specified (ignoring)
> [ 14.010] (II) config/udev: Adding input device Sleep Button
> (/dev/input/event2)
> [ 14.010] (**) Sleep Button: Applying InputClass "evdev keyboard catchall"
> [ 14.010] (II) Using input driver 'evdev' for 'Sleep Button'
> [ 14.010] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
> [ 14.010] (**) Sleep Button: always reports core events
> [ 14.010] (**) Sleep Button: Device: "/dev/input/event2"
> [ 14.010] (--) Sleep Button: Found keys
> [ 14.010] (II) Sleep Button: Configuring as keyboard
> [ 14.010] (**) Option "config_info"
> "udev:/sys/devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input2/event2"
> [ 14.010] (II) XINPUT: Adding extended input device "Sleep Button"
> (type: KEYBOARD)
> [ 14.010] (**) Option "xkb_rules" "evdev"
> [ 14.010] (**) Option "xkb_model" "pc105"
> [ 14.010] (**) Option "xkb_layout" "us"
> [ 14.014] (II) config/udev: Adding input device Logitech USB-PS/2
> Optical Mouse (/dev/input/event5)
> [ 14.014] (**) Logitech USB-PS/2 Optical Mouse: Applying InputClass
> "evdev pointer catchall"
> [ 14.015] (II) Using input driver 'evdev' for 'Logitech USB-PS/2
> Optical Mouse'
> [ 14.015] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
> [ 14.015] (**) Logitech USB-PS/2 Optical Mouse: always reports core events
> [ 14.015] (**) Logitech USB-PS/2 Optical Mouse: Device: "/dev/input/event5"
> [ 14.015] (--) Logitech USB-PS/2 Optical Mouse: Found 3 mouse buttons
> [ 14.015] (--) Logitech USB-PS/2 Optical Mouse: Found scroll wheel(s)
> [ 14.015] (--) Logitech USB-PS/2 Optical Mouse: Found relative axes
> [ 14.015] (--) Logitech USB-PS/2 Optical Mouse: Found x and y relative axes
> [ 14.015] (II) Logitech USB-PS/2 Optical Mouse: Configuring as mouse
> [ 14.015] (II) Logitech USB-PS/2 Optical Mouse: Adding scrollwheel support
> [ 14.015] (**) Logitech USB-PS/2 Optical Mouse: YAxisMapping: buttons 4 and 5
> [ 14.015] (**) Logitech USB-PS/2 Optical Mouse: EmulateWheelButton:
> 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
> [ 14.015] (**) Option "config_info"
> "udev:/sys/devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.2/2-1.2:1.0/input/input5/event5"
> [ 14.015] (II) XINPUT: Adding extended input device "Logitech
> USB-PS/2 Optical Mouse" (type: MOUSE)
> [ 14.015] (II) Logitech USB-PS/2 Optical Mouse: initialized for
> relative axes.
> [ 14.015] (**) Logitech USB-PS/2 Optical Mouse: (accel) keeping
> acceleration scheme 1
> [ 14.015] (**) Logitech USB-PS/2 Optical Mouse: (accel)
> acceleration profile 0
> [ 14.015] (**) Logitech USB-PS/2 Optical Mouse: (accel)
> acceleration factor: 2.000
> [ 14.015] (**) Logitech USB-PS/2 Optical Mouse: (accel)
> acceleration threshold: 4
> [ 14.060] (EE) FBDEV(0): FBIOBLANK: Invalid argument
> [ 15.227] (EE) FBDEV(0): FBIOBLANK: Invalid argument
> [ 56.003] (II) config/udev: Adding input device HID 046a:0001
> (/dev/input/event6)
> [ 56.003] (**) HID 046a:0001: Applying InputClass "evdev keyboard catchall"
> [ 56.003] (II) Using input driver 'evdev' for 'HID 046a:0001'
> [ 56.003] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
> [ 56.003] (**) HID 046a:0001: always reports core events
> [ 56.003] (**) HID 046a:0001: Device: "/dev/input/event6"
> [ 56.003] (--) HID 046a:0001: Found keys
> [ 56.003] (II) HID 046a:0001: Configuring as keyboard
> [ 56.003] (**) Option "config_info"
> "udev:/sys/devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.4/2-1.4:1.0/input/input6/event6"
> [ 56.003] (II) XINPUT: Adding extended input device "HID 046a:0001"
> (type: KEYBOARD)
> [ 56.003] (**) Option "xkb_rules" "evdev"
> [ 56.003] (**) Option "xkb_model" "pc105"
> [ 56.003] (**) Option "xkb_layout" "us"
>
>
> Thanks
> ---
> Christian Gmeiner, MSc
> _______________________________________________
> Intel-gfx mailing list
> Intel-gfx at lists.freedesktop.org
> http://lists.freedesktop.org/mailman/listinfo/intel-gfx
More information about the Intel-gfx
mailing list