[Intel-gfx] [PATCH 6/8] drm/i915: move intel_update_lvds to intel_lvds->pre_pll_enable
Daniel Vetter
daniel.vetter at ffwll.ch
Mon Nov 5 13:28:25 CET 2012
A few things needed to change:
- HAS_PCH_SPLIT since ilk+ is not yet converted to this.
- s/LVDS/intel_lvds->reg/ to prep for ilk conversion
- replace the clock.p2 == 7 check with a is_dual_link check
- s/adjusted_mode/intel_lvds->fixed_mode
v2: Rebase on top of Jani Nikula's panel rework. I'm wondering whether
we shouldn't add an attached_panel pointer to intel_encoder, to
replace the encoder private ->attached_connector pointers, since
that's essentially what we need.
Signed-off-by: Daniel Vetter <daniel.vetter at ffwll.ch>
---
drivers/gpu/drm/i915/intel_display.c | 59 ------------------------------------
drivers/gpu/drm/i915/intel_lvds.c | 57 ++++++++++++++++++++++++++++++++++
2 files changed, 57 insertions(+), 59 deletions(-)
diff --git a/drivers/gpu/drm/i915/intel_display.c b/drivers/gpu/drm/i915/intel_display.c
index 7309790..bd3fa2b 100644
--- a/drivers/gpu/drm/i915/intel_display.c
+++ b/drivers/gpu/drm/i915/intel_display.c
@@ -4259,51 +4259,6 @@ static void i9xx_update_pll_dividers(struct drm_crtc *crtc,
}
}
-static void intel_update_lvds(struct drm_crtc *crtc, intel_clock_t *clock,
- struct drm_display_mode *adjusted_mode)
-{
- struct drm_device *dev = crtc->dev;
- struct drm_i915_private *dev_priv = dev->dev_private;
- struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
- int pipe = intel_crtc->pipe;
- u32 temp;
-
- temp = I915_READ(LVDS);
- temp |= LVDS_PORT_EN | LVDS_A0A2_CLKA_POWER_UP;
- if (pipe == 1) {
- temp |= LVDS_PIPEB_SELECT;
- } else {
- temp &= ~LVDS_PIPEB_SELECT;
- }
- /* set the corresponsding LVDS_BORDER bit */
- temp |= dev_priv->lvds_border_bits;
- /* Set the B0-B3 data pairs corresponding to whether we're going to
- * set the DPLLs for dual-channel mode or not.
- */
- if (clock->p2 == 7)
- temp |= LVDS_B0B3_POWER_UP | LVDS_CLKB_POWER_UP;
- else
- temp &= ~(LVDS_B0B3_POWER_UP | LVDS_CLKB_POWER_UP);
-
- /* It would be nice to set 24 vs 18-bit mode (LVDS_A3_POWER_UP)
- * appropriately here, but we need to look more thoroughly into how
- * panels behave in the two modes.
- */
- /* set the dithering flag on LVDS as needed */
- if (INTEL_INFO(dev)->gen >= 4) {
- if (dev_priv->lvds_dither)
- temp |= LVDS_ENABLE_DITHER;
- else
- temp &= ~LVDS_ENABLE_DITHER;
- }
- temp &= ~(LVDS_HSYNC_POLARITY | LVDS_VSYNC_POLARITY);
- if (adjusted_mode->flags & DRM_MODE_FLAG_NHSYNC)
- temp |= LVDS_HSYNC_POLARITY;
- if (adjusted_mode->flags & DRM_MODE_FLAG_NVSYNC)
- temp |= LVDS_VSYNC_POLARITY;
- I915_WRITE(LVDS, temp);
-}
-
static void vlv_update_pll(struct drm_crtc *crtc,
struct drm_display_mode *mode,
struct drm_display_mode *adjusted_mode,
@@ -4486,13 +4441,6 @@ static void i9xx_update_pll(struct drm_crtc *crtc,
if (encoder->pre_pll_enable)
encoder->pre_pll_enable(encoder);
- /* The LVDS pin pair needs to be on before the DPLLs are enabled.
- * This is an exception to the general rule that mode_set doesn't turn
- * things on.
- */
- if (intel_pipe_has_type(crtc, INTEL_OUTPUT_LVDS))
- intel_update_lvds(crtc, clock, adjusted_mode);
-
if (intel_pipe_has_type(crtc, INTEL_OUTPUT_DISPLAYPORT))
intel_dp_set_m_n(crtc, mode, adjusted_mode);
@@ -4568,13 +4516,6 @@ static void i8xx_update_pll(struct drm_crtc *crtc,
if (encoder->pre_pll_enable)
encoder->pre_pll_enable(encoder);
- /* The LVDS pin pair needs to be on before the DPLLs are enabled.
- * This is an exception to the general rule that mode_set doesn't turn
- * things on.
- */
- if (intel_pipe_has_type(crtc, INTEL_OUTPUT_LVDS))
- intel_update_lvds(crtc, clock, adjusted_mode);
-
I915_WRITE(DPLL(pipe), dpll);
/* Wait for the clocks to stabilize. */
diff --git a/drivers/gpu/drm/i915/intel_lvds.c b/drivers/gpu/drm/i915/intel_lvds.c
index 972ef12..057e29a 100644
--- a/drivers/gpu/drm/i915/intel_lvds.c
+++ b/drivers/gpu/drm/i915/intel_lvds.c
@@ -89,6 +89,62 @@ static bool intel_lvds_get_hw_state(struct intel_encoder *encoder,
return true;
}
+/* The LVDS pin pair needs to be on before the DPLLs are enabled.
+ * This is an exception to the general rule that mode_set doesn't turn
+ * things on.
+ */
+static void intel_pre_pll_enable_lvds(struct intel_encoder *encoder)
+{
+ struct intel_lvds_encoder *lvds_encoder = to_lvds_encoder(&encoder->base);
+ struct drm_device *dev = encoder->base.dev;
+ struct drm_i915_private *dev_priv = dev->dev_private;
+ struct intel_crtc *intel_crtc = to_intel_crtc(encoder->base.crtc);
+ struct drm_display_mode *fixed_mode =
+ lvds_encoder->attached_connector->base.panel.fixed_mode;
+ int pipe = intel_crtc->pipe;
+ u32 temp;
+
+ /* pch split platforms are not yet converted. */
+ if (HAS_PCH_SPLIT(dev))
+ return;
+
+ temp = I915_READ(lvds_encoder->reg);
+ temp |= LVDS_PORT_EN | LVDS_A0A2_CLKA_POWER_UP;
+ if (pipe == 1) {
+ temp |= LVDS_PIPEB_SELECT;
+ } else {
+ temp &= ~LVDS_PIPEB_SELECT;
+ }
+ /* set the corresponsding LVDS_BORDER bit */
+ temp |= dev_priv->lvds_border_bits;
+ /* Set the B0-B3 data pairs corresponding to whether we're going to
+ * set the DPLLs for dual-channel mode or not.
+ */
+ if (lvds_encoder->is_dual_link)
+ temp |= LVDS_B0B3_POWER_UP | LVDS_CLKB_POWER_UP;
+ else
+ temp &= ~(LVDS_B0B3_POWER_UP | LVDS_CLKB_POWER_UP);
+
+ /* It would be nice to set 24 vs 18-bit mode (LVDS_A3_POWER_UP)
+ * appropriately here, but we need to look more thoroughly into how
+ * panels behave in the two modes.
+ */
+ /* set the dithering flag on LVDS as needed */
+ if (INTEL_INFO(dev)->gen >= 4) {
+ if (dev_priv->lvds_dither)
+ temp |= LVDS_ENABLE_DITHER;
+ else
+ temp &= ~LVDS_ENABLE_DITHER;
+ }
+ temp &= ~(LVDS_HSYNC_POLARITY | LVDS_VSYNC_POLARITY);
+ if (fixed_mode->flags & DRM_MODE_FLAG_NHSYNC)
+ temp |= LVDS_HSYNC_POLARITY;
+ if (fixed_mode->flags & DRM_MODE_FLAG_NVSYNC)
+ temp |= LVDS_VSYNC_POLARITY;
+
+ I915_WRITE(lvds_encoder->reg, temp);
+}
+
/**
* Sets the power state for the panel.
*/
@@ -1038,6 +1094,7 @@ bool intel_lvds_init(struct drm_device *dev)
DRM_MODE_ENCODER_LVDS);
intel_encoder->enable = intel_enable_lvds;
+ intel_encoder->pre_pll_enable = intel_pre_pll_enable_lvds;
intel_encoder->disable = intel_disable_lvds;
intel_encoder->get_hw_state = intel_lvds_get_hw_state;
intel_connector->get_hw_state = intel_connector_get_hw_state;
--
1.7.11.7
More information about the Intel-gfx
mailing list