[Intel-gfx] [PATCH 2/2] drm/i915: Prevent loading of uninitialized context garbage

[Abdiel Janulgue]

On Wednesday, August 21, 2013 11:12:36 PM Daniel Vetter wrote:
> On Wed, Aug 21, 2013 at 06:31:07PM +0300, Ville Syrjälä wrote:
> > On Wed, Aug 21, 2013 at 04:43:33PM +0300, Ville Syrjälä wrote:
> > > On Thu, Aug 08, 2013 at 08:00:26PM +0100, Chris Wilson wrote:
> > > > The extended state bits are stored in the LCA register and affect all
> > > > updates to the LCA register - i.e. the state on the old context is
> > > > saved
> > > > when SAVE_EX_STATE_EN  is currently set in the old context address
> > > > before
> > > > the update, and the new context is restored when RESTORE_EX_STATE_EN
> > > > is
> > > > set in the new context address. This is irrespective of the
> > > > RESTORE_INHIBIT flag in the MI_SET_CONTEXT.
> > > > 
> > > > Hence, upon initial loading the contents of the extended state is read
> > > > from uninitialised data. To workaround this, on first load we do a
> > > > dummy
> > > > load without the mandatory RESTORE_EX_STATE_EN bit so that the real
> > > > load
> > > > causes us to initialise the extended state of the context before it is
> > > > then loaded by the LCA update.
> > > > 
> > > > v2: Split out the introduction of the variable length MI_SET_CONTEXT
> > > > command sequence.
> > > > 
> > > > References: https://bugs.freedesktop.org/show_bug.cgi?id=64073
> > > > Signed-off-by: Chris Wilson <chris at chris-wilson.co.uk>
> > > > Cc: Ben Widawsky <ben at bwidawsk.net>
> > > > ---
> > > > 
> > > >  drivers/gpu/drm/i915/i915_gem_context.c | 18 ++++++++++++++++++
> > > >  1 file changed, 18 insertions(+)
> > > > 
> > > > diff --git a/drivers/gpu/drm/i915/i915_gem_context.c
> > > > b/drivers/gpu/drm/i915/i915_gem_context.c index 8a7b61e..a57d49a
> > > > 100644
> > > > --- a/drivers/gpu/drm/i915/i915_gem_context.c
> > > > +++ b/drivers/gpu/drm/i915/i915_gem_context.c
> > > > @@ -367,6 +367,8 @@ mi_set_context(struct intel_ring_buffer *ring,
> > > > 
> > > >  	case 5: len += 2;
> > > >  	
> > > >  		break;
> > > >  	
> > > >  	}
> > > > 
> > > > +	if (!new_context->is_initialized)
> > > > +		len += 2;
> > > > 
> > > >  	ret = intel_ring_begin(ring, len);
> > > >  	if (ret)
> > > > 
> > > > @@ -382,6 +384,22 @@ mi_set_context(struct intel_ring_buffer *ring,
> > > > 
> > > >  		break;
> > > >  	
> > > >  	}
> > > > 
> > > > +	if (!new_context->is_initialized) {
> > > > +		/* The GPU tries to restore the extended state irrespective
> > > > +		 * of RestoreInhibit (since it is part of the LCA switch
> > > > +		 * itself rather than the MI_SET_CONTEXT command).
> > > > +		 * Since the initial contents may be garbage we do a dummy
> > > > +		 * load first then set the mandatory flag for any future
> > > > +		 * ring context switches.
> > > > +		 */
> > > > +		intel_ring_emit(ring, MI_SET_CONTEXT);
> > > > +		intel_ring_emit(ring,
> > > > +				i915_gem_obj_ggtt_offset(new_context->obj) |
> > > > +				MI_MM_SPACE_GTT |
> > > > +				MI_SAVE_EXT_STATE_EN |
> > > > +				hw_flags);
> > > > +	}
> > > 
> > > Hmm. Couldn't we just do this w/ one MI_SET_CONTEXT? Just drop the
> > > MI_RESTORE_EXT_STATE_EN flag if the context is not initialized. The
> > > MI_SAVE_EXT_STATE_EN will be saved in the CCID, so when we switch to
> > > another context the extended state will be saved. And for the next
> > > switch to this context we will set the MI_RESTORE_EXT_STATE_EN bit
> > > in MI_SET_CONTEXT so it should get restored.
> > > 
> > > But I must admit BSpec is a bit confusing on the topic. It says the
> > > restore bit affects the switch to the context specified in the
> > > logical context address. I take that to mean that the effect of the
> > > restore bit is immediate. But BSpec also says that the bit is stored in
> > > CCID to control the subsequent switch to the same context. So does that
> > > actually mean that 'effective.restore_ext = CCID.restore_ext |
> > > MI_SET_CONTEXT.restore_ext'?
> > > 
> > > Oh, but BSpec also says that both bits must be set when RS2 power state
> > > is enabled. I think that's the same as RC6, or is it? So I guess the
> > > hardware might consult these bits when entering/leaving RC6. So I
> > > suppose
> > > we really need to make sure both bits are always set in case we hit RC6.
> > > So based on that reasoning the patch would seem correct.
> > > 
> > > I guess I'll give it an r-b regardless :)
> > > 
> > > Reviewed-by: Ville Syrjälä <ville.syrjala at linux.intel.com>
> > 
> > I just noticed that on HSW these bits control the resource streamer
> > state save/restore. The spec says we should always set the RS
> > restore bit if we set the RS save bit. So maybe we need some
> > !IS_HASWELL checks in there...
> 
> Looks like we're lucky since we don't have RS support yet ;-) Can you
> please poke Abdiel about this so we make sure to test/check for this?
> Cc'ing him.

The RS State Save/Restore bits on MI_SET_CONTEXT should probably be switched 
on only when we have the RS enabled. Basically it saves RS state (hw-bt 
images, gather image) and would not make sense to enable this bit without RS 
filling this data. I am not sure of the behaviour though when this bit is set 
and the RS switched off.

-Abdiel