[Intel-gfx] [PATCH 07/19] drm/i915: move pipe bpp computation to pipe_config
Daniel Vetter
daniel.vetter at ffwll.ch
Wed Feb 13 12:32:10 CET 2013
The procedure has now 3 steps:
1. Compute the bpp that the plane will output, this is done in
pipe_config_set_bpp and stored into pipe_config->pipe_bpp. Also,
this function clamps the pipe_bpp to whatever limit the EDID of any
connected output specifies.
2. Adjust the pipe_bpp in the encoder and crtc functions, according to
whatever constraints there are.
3. Decide whether to use dither by comparing the stored plane bpp with
computed pipe_bpp.
There are a few slight functional changes in this patch:
- LVDS connector are now also going through the EDID clamping. But in
a 2nd change we now unconditionally force the lvds bpc value - this
shouldn't matter in reality when the panel setup is consistent, but
better safe than sorry.
- HDMI now forces the pipe_bpp to the selected value - I think that's
what we actually want, since otherwise at least the pixelclock
computations are wrong (I'm not sure whether the port would accept
e.g. 10 bpc when in 12bpc mode). Contrary to the old code, we pick
the next higher bpc value, since otherwise there's no way to make
use of the 12 bpc mode (since the next patch will remove the 12bpc
plane format, it doesn't exist).
Both of these changes are due to the removal of the
pipe_bpp = min(display_bpp, plane_bpp);
statement.
Another slight change is the reworking of the dp bpc code:
- For the mode_valid callback it's sufficient to only check whether
the mode would fit at the lowest bpc.
- The bandwidth computation code is a bit restructured: It now walks
all available bpp values in an outer loop and the codeblock the
compute derived values (once a good configuration is found) has been
moved out of the for loop maze. This is prep work to allow us to
successively fall back on bpc values, and also correctly support bpc
values != 8 or 6.
If we ever get around to adding additional dithering (e.g. to squeeze
a mode into 2 fdi lanes), we need to add a flag that tells the crtc
configuration adjusting code that the bpp value selected by the output
can't be lowered. Since we don't have such logic for now, let it be.
v2: Rebased on top of Paulo Zanoni's little refactoring to use more
drm dp helper functions.
v3: Rebased on top of Jani's eDP bpp fix and Ville's limited color
range work.
v4: Remove the INTEL_MODE_DP_FORCE_6BPC #define, no longer needed.
Signed-off-by: Daniel Vetter <daniel.vetter at ffwll.ch>
---
drivers/gpu/drm/i915/intel_ddi.c | 11 +-
drivers/gpu/drm/i915/intel_display.c | 221 ++++++++++++-----------------------
drivers/gpu/drm/i915/intel_dp.c | 103 ++++++++--------
drivers/gpu/drm/i915/intel_drv.h | 8 +-
drivers/gpu/drm/i915/intel_hdmi.c | 15 +++
drivers/gpu/drm/i915/intel_lvds.c | 11 ++
6 files changed, 152 insertions(+), 217 deletions(-)
diff --git a/drivers/gpu/drm/i915/intel_ddi.c b/drivers/gpu/drm/i915/intel_ddi.c
index 0ae21be..a9b1b0e 100644
--- a/drivers/gpu/drm/i915/intel_ddi.c
+++ b/drivers/gpu/drm/i915/intel_ddi.c
@@ -924,7 +924,7 @@ void intel_ddi_set_pipe_settings(struct drm_crtc *crtc)
if (type == INTEL_OUTPUT_DISPLAYPORT || type == INTEL_OUTPUT_EDP) {
temp = TRANS_MSA_SYNC_CLK;
- switch (intel_crtc->bpp) {
+ switch (intel_crtc->config.pipe_bpp) {
case 18:
temp |= TRANS_MSA_6_BPC;
break;
@@ -938,9 +938,7 @@ void intel_ddi_set_pipe_settings(struct drm_crtc *crtc)
temp |= TRANS_MSA_12_BPC;
break;
default:
- temp |= TRANS_MSA_8_BPC;
- WARN(1, "%d bpp unsupported by DDI function\n",
- intel_crtc->bpp);
+ BUG();
}
I915_WRITE(TRANS_MSA_MISC(cpu_transcoder), temp);
}
@@ -962,7 +960,7 @@ void intel_ddi_enable_pipe_func(struct drm_crtc *crtc)
temp = TRANS_DDI_FUNC_ENABLE;
temp |= TRANS_DDI_SELECT_PORT(port);
- switch (intel_crtc->bpp) {
+ switch (intel_crtc->config.pipe_bpp) {
case 18:
temp |= TRANS_DDI_BPC_6;
break;
@@ -976,8 +974,7 @@ void intel_ddi_enable_pipe_func(struct drm_crtc *crtc)
temp |= TRANS_DDI_BPC_12;
break;
default:
- WARN(1, "%d bpp unsupported by transcoder DDI function\n",
- intel_crtc->bpp);
+ BUG();
}
if (crtc->mode.flags & DRM_MODE_FLAG_PVSYNC)
diff --git a/drivers/gpu/drm/i915/intel_display.c b/drivers/gpu/drm/i915/intel_display.c
index 327d126..d686b26 100644
--- a/drivers/gpu/drm/i915/intel_display.c
+++ b/drivers/gpu/drm/i915/intel_display.c
@@ -3985,142 +3985,6 @@ static inline bool intel_panel_use_ssc(struct drm_i915_private *dev_priv)
&& !(dev_priv->quirks & QUIRK_LVDS_SSC_DISABLE);
}
-/**
- * intel_choose_pipe_bpp_dither - figure out what color depth the pipe should send
- * @crtc: CRTC structure
- * @mode: requested mode
- *
- * A pipe may be connected to one or more outputs. Based on the depth of the
- * attached framebuffer, choose a good color depth to use on the pipe.
- *
- * If possible, match the pipe depth to the fb depth. In some cases, this
- * isn't ideal, because the connected output supports a lesser or restricted
- * set of depths. Resolve that here:
- * LVDS typically supports only 6bpc, so clamp down in that case
- * HDMI supports only 8bpc or 12bpc, so clamp to 8bpc with dither for 10bpc
- * Displays may support a restricted set as well, check EDID and clamp as
- * appropriate.
- * DP may want to dither down to 6bpc to fit larger modes
- *
- * RETURNS:
- * Dithering requirement (i.e. false if display bpc and pipe bpc match,
- * true if they don't match).
- */
-static bool intel_choose_pipe_bpp_dither(struct drm_crtc *crtc,
- struct drm_framebuffer *fb,
- unsigned int *pipe_bpp,
- struct drm_display_mode *mode)
-{
- struct drm_device *dev = crtc->dev;
- struct drm_i915_private *dev_priv = dev->dev_private;
- struct drm_connector *connector;
- struct intel_encoder *intel_encoder;
- unsigned int display_bpc = UINT_MAX, bpc;
-
- /* Walk the encoders & connectors on this crtc, get min bpc */
- for_each_encoder_on_crtc(dev, crtc, intel_encoder) {
-
- if (intel_encoder->type == INTEL_OUTPUT_LVDS) {
- unsigned int lvds_bpc;
-
- if ((I915_READ(PCH_LVDS) & LVDS_A3_POWER_MASK) ==
- LVDS_A3_POWER_UP)
- lvds_bpc = 8;
- else
- lvds_bpc = 6;
-
- if (lvds_bpc < display_bpc) {
- DRM_DEBUG_KMS("clamping display bpc (was %d) to LVDS (%d)\n", display_bpc, lvds_bpc);
- display_bpc = lvds_bpc;
- }
- continue;
- }
-
- /* Not one of the known troublemakers, check the EDID */
- list_for_each_entry(connector, &dev->mode_config.connector_list,
- head) {
- if (connector->encoder != &intel_encoder->base)
- continue;
-
- /* Don't use an invalid EDID bpc value */
- if (connector->display_info.bpc &&
- connector->display_info.bpc < display_bpc) {
- DRM_DEBUG_KMS("clamping display bpc (was %d) to EDID reported max of %d\n", display_bpc, connector->display_info.bpc);
- display_bpc = connector->display_info.bpc;
- }
- }
-
- if (intel_encoder->type == INTEL_OUTPUT_EDP) {
- /* Use VBT settings if we have an eDP panel */
- unsigned int edp_bpc = dev_priv->edp.bpp / 3;
-
- if (edp_bpc && edp_bpc < display_bpc) {
- DRM_DEBUG_KMS("clamping display bpc (was %d) to eDP (%d)\n", display_bpc, edp_bpc);
- display_bpc = edp_bpc;
- }
- continue;
- }
-
- /*
- * HDMI is either 12 or 8, so if the display lets 10bpc sneak
- * through, clamp it down. (Note: >12bpc will be caught below.)
- */
- if (intel_encoder->type == INTEL_OUTPUT_HDMI) {
- if (display_bpc > 8 && display_bpc < 12) {
- DRM_DEBUG_KMS("forcing bpc to 12 for HDMI\n");
- display_bpc = 12;
- } else {
- DRM_DEBUG_KMS("forcing bpc to 8 for HDMI\n");
- display_bpc = 8;
- }
- }
- }
-
- if (mode->private_flags & INTEL_MODE_DP_FORCE_6BPC) {
- DRM_DEBUG_KMS("Dithering DP to 6bpc\n");
- display_bpc = 6;
- }
-
- /*
- * We could just drive the pipe at the highest bpc all the time and
- * enable dithering as needed, but that costs bandwidth. So choose
- * the minimum value that expresses the full color range of the fb but
- * also stays within the max display bpc discovered above.
- */
-
- switch (fb->depth) {
- case 8:
- bpc = 8; /* since we go through a colormap */
- break;
- case 15:
- case 16:
- bpc = 6; /* min is 18bpp */
- break;
- case 24:
- bpc = 8;
- break;
- case 30:
- bpc = 10;
- break;
- case 48:
- bpc = 12;
- break;
- default:
- DRM_DEBUG("unsupported depth, assuming 24 bits\n");
- bpc = min((unsigned int)8, display_bpc);
- break;
- }
-
- display_bpc = min(display_bpc, bpc);
-
- DRM_DEBUG_KMS("setting pipe bpc to %d (max display bpc %d)\n",
- bpc, display_bpc);
-
- *pipe_bpp = display_bpc * 3;
-
- return display_bpc != bpc;
-}
-
static int vlv_get_refclk(struct drm_crtc *crtc)
{
struct drm_device *dev = crtc->dev;
@@ -4676,7 +4540,7 @@ static int i9xx_crtc_mode_set(struct drm_crtc *crtc,
/* default to 8bpc */
pipeconf &= ~(PIPECONF_BPC_MASK | PIPECONF_DITHER_EN);
if (is_dp) {
- if (adjusted_mode->private_flags & INTEL_MODE_DP_FORCE_6BPC) {
+ if (intel_crtc->config.dither) {
pipeconf |= PIPECONF_6BPC |
PIPECONF_DITHER_EN |
PIPECONF_DITHER_TYPE_SP;
@@ -4684,7 +4548,7 @@ static int i9xx_crtc_mode_set(struct drm_crtc *crtc,
}
if (IS_VALLEYVIEW(dev) && intel_pipe_has_type(crtc, INTEL_OUTPUT_EDP)) {
- if (adjusted_mode->private_flags & INTEL_MODE_DP_FORCE_6BPC) {
+ if (intel_crtc->config.dither) {
pipeconf |= PIPECONF_6BPC |
PIPECONF_ENABLE |
I965_PIPECONF_ACTIVE;
@@ -5073,7 +4937,7 @@ static void ironlake_set_pipeconf(struct drm_crtc *crtc,
val = I915_READ(PIPECONF(pipe));
val &= ~PIPECONF_BPC_MASK;
- switch (intel_crtc->bpp) {
+ switch (intel_crtc->config.pipe_bpp) {
case 18:
val |= PIPECONF_6BPC;
break;
@@ -5369,13 +5233,14 @@ static void ironlake_fdi_set_m_n(struct drm_crtc *crtc)
target_clock = adjusted_mode->clock;
lane = ironlake_get_lanes_required(target_clock, link_bw,
- intel_crtc->bpp);
+ intel_crtc->config.pipe_bpp);
intel_crtc->fdi_lanes = lane;
if (intel_crtc->config.pixel_multiplier > 1)
link_bw *= intel_crtc->config.pixel_multiplier;
- intel_link_compute_m_n(intel_crtc->bpp, lane, target_clock, link_bw, &m_n);
+ intel_link_compute_m_n(intel_crtc->config.pipe_bpp, lane, target_clock,
+ link_bw, &m_n);
intel_cpu_transcoder_set_m_n(intel_crtc, &m_n);
}
@@ -5537,8 +5402,7 @@ static int ironlake_crtc_mode_set(struct drm_crtc *crtc,
intel_crtc_update_cursor(crtc, true);
/* determine panel color depth */
- dither = intel_choose_pipe_bpp_dither(crtc, fb, &intel_crtc->bpp,
- adjusted_mode);
+ dither = intel_crtc->config.dither;
if (is_lvds && dev_priv->lvds_dither)
dither = true;
@@ -5705,8 +5569,7 @@ static int haswell_crtc_mode_set(struct drm_crtc *crtc,
intel_crtc_update_cursor(crtc, true);
/* determine panel color depth */
- dither = intel_choose_pipe_bpp_dither(crtc, fb, &intel_crtc->bpp,
- adjusted_mode);
+ dither = intel_crtc->config.dither;
DRM_DEBUG_KMS("Mode for pipe %d:\n", pipe);
drm_mode_debug_printmodeline(mode);
@@ -7392,14 +7255,72 @@ static void intel_modeset_commit_output_state(struct drm_device *dev)
}
}
+static int
+pipe_config_set_bpp(struct drm_crtc *crtc,
+ struct drm_framebuffer *fb,
+ struct intel_crtc_config *pipe_config)
+{
+ struct drm_device *dev = crtc->dev;
+ struct drm_connector *connector;
+ int bpp;
+
+ switch (fb->depth) {
+ case 8:
+ bpp = 8*3; /* since we go through a colormap */
+ break;
+ case 15:
+ case 16:
+ bpp = 6*3; /* min is 18bpp */
+ break;
+ case 24:
+ bpp = 8*3;
+ break;
+ case 30:
+ bpp = 10*3;
+ break;
+ case 48:
+ bpp = 12*3;
+ break;
+ default:
+ DRM_DEBUG_KMS("unsupported depth\n");
+ return -EINVAL;
+ }
+
+ if (fb->depth > 24 && !HAS_PCH_SPLIT(dev)) {
+ DRM_DEBUG_KMS("high depth not supported on gmch platforms\n");
+ return -EINVAL;
+ }
+
+ pipe_config->pipe_bpp = bpp;
+
+ /* Clamp display bpp to did value */
+ list_for_each_entry(connector, &dev->mode_config.connector_list,
+ head) {
+ if (connector->encoder && connector->encoder->crtc != crtc)
+ continue;
+
+ /* Don't use an invalid EDID bpc value */
+ if (connector->display_info.bpc &&
+ connector->display_info.bpc * 3 < bpp) {
+ DRM_DEBUG_KMS("clamping display bpp (was %d) to EDID reported max of %d\n",
+ bpp, connector->display_info.bpc*3);
+ pipe_config->pipe_bpp = connector->display_info.bpc*3;
+ }
+ }
+
+ return bpp;
+}
+
static struct intel_crtc_config *
intel_modeset_pipe_config(struct drm_crtc *crtc,
+ struct drm_framebuffer *fb,
struct drm_display_mode *mode)
{
struct drm_device *dev = crtc->dev;
struct drm_encoder_helper_funcs *encoder_funcs;
struct intel_encoder *encoder;
struct intel_crtc_config *pipe_config;
+ int bpp;
pipe_config = kzalloc(sizeof(*pipe_config), GFP_KERNEL);
if (!pipe_config)
@@ -7410,6 +7331,10 @@ intel_modeset_pipe_config(struct drm_crtc *crtc,
pipe_config->requested_mode = *mode;
pipe_config->requested_mode.base.id = 0;
+ bpp = pipe_config_set_bpp(crtc, fb, pipe_config);
+ if (bpp < 0)
+ goto fail;
+
/* Pass our mode to the connectors and the CRTC to give them a chance to
* adjust it according to limitations or connector properties, and also
* a chance to reject the mode entirely.
@@ -7444,6 +7369,8 @@ intel_modeset_pipe_config(struct drm_crtc *crtc,
}
DRM_DEBUG_KMS("[CRTC:%d]\n", crtc->base.id);
+ pipe_config->dither = pipe_config->pipe_bpp != bpp;
+
return pipe_config;
fail:
kfree(pipe_config);
@@ -7736,7 +7663,7 @@ int intel_set_mode(struct drm_crtc *crtc,
* changing their mode at the same time. */
pipe_config = NULL;
if (modeset_pipes) {
- pipe_config = intel_modeset_pipe_config(crtc, mode);
+ pipe_config = intel_modeset_pipe_config(crtc, fb, mode);
if (IS_ERR(pipe_config)) {
goto out;
}
@@ -8175,8 +8102,6 @@ static void intel_crtc_init(struct drm_device *dev, int pipe)
dev_priv->plane_to_crtc_mapping[intel_crtc->plane] = &intel_crtc->base;
dev_priv->pipe_to_crtc_mapping[intel_crtc->pipe] = &intel_crtc->base;
- intel_crtc->bpp = 24; /* default for pre-Ironlake */
-
drm_crtc_helper_add(&intel_crtc->base, &intel_helper_funcs);
}
diff --git a/drivers/gpu/drm/i915/intel_dp.c b/drivers/gpu/drm/i915/intel_dp.c
index 1da5518..0ccaeb3 100644
--- a/drivers/gpu/drm/i915/intel_dp.c
+++ b/drivers/gpu/drm/i915/intel_dp.c
@@ -177,34 +177,6 @@ intel_dp_max_data_rate(int max_link_clock, int max_lanes)
return (max_link_clock * max_lanes * 8) / 10;
}
-static bool
-intel_dp_adjust_dithering(struct intel_dp *intel_dp,
- struct drm_display_mode *mode,
- bool adjust_mode)
-{
- int max_link_clock =
- drm_dp_bw_code_to_link_rate(intel_dp_max_link_bw(intel_dp));
- int max_lanes = drm_dp_max_lane_count(intel_dp->dpcd);
- int max_rate, mode_rate;
-
- mode_rate = intel_dp_link_required(mode->clock, 24);
- max_rate = intel_dp_max_data_rate(max_link_clock, max_lanes);
-
- if (mode_rate > max_rate) {
- mode_rate = intel_dp_link_required(mode->clock, 18);
- if (mode_rate > max_rate)
- return false;
-
- if (adjust_mode)
- mode->private_flags
- |= INTEL_MODE_DP_FORCE_6BPC;
-
- return true;
- }
-
- return true;
-}
-
static int
intel_dp_mode_valid(struct drm_connector *connector,
struct drm_display_mode *mode)
@@ -212,6 +184,8 @@ intel_dp_mode_valid(struct drm_connector *connector,
struct intel_dp *intel_dp = intel_attached_dp(connector);
struct intel_connector *intel_connector = to_intel_connector(connector);
struct drm_display_mode *fixed_mode = intel_connector->panel.fixed_mode;
+ int target_clock = mode->clock;
+ int max_rate, mode_rate, max_lanes, max_link_clock;
if (is_edp(intel_dp) && fixed_mode) {
if (mode->hdisplay > fixed_mode->hdisplay)
@@ -221,7 +195,13 @@ intel_dp_mode_valid(struct drm_connector *connector,
return MODE_PANEL;
}
- if (!intel_dp_adjust_dithering(intel_dp, mode, false))
+ max_link_clock = drm_dp_bw_code_to_link_rate(intel_dp_max_link_bw(intel_dp));
+ max_lanes = drm_dp_max_lane_count(intel_dp->dpcd);
+
+ max_rate = intel_dp_max_data_rate(max_link_clock, max_lanes);
+ mode_rate = intel_dp_link_required(target_clock, 18);
+
+ if (mode_rate > max_rate)
return MODE_CLOCK_HIGH;
if (mode->clock < 10000)
@@ -735,6 +715,7 @@ intel_dp_compute_config(struct intel_encoder *encoder,
struct intel_crtc_config *pipe_config)
{
struct drm_device *dev = encoder->base.dev;
+ struct drm_i915_private *dev_priv = dev->dev_private;
struct drm_display_mode *adjusted_mode = &pipe_config->adjusted_mode;
struct drm_display_mode *mode = &pipe_config->requested_mode;
struct intel_dp *intel_dp = enc_to_intel_dp(&encoder->base);
@@ -744,6 +725,7 @@ intel_dp_compute_config(struct intel_encoder *encoder,
int max_clock = intel_dp_max_link_bw(intel_dp) == DP_LINK_BW_2_7 ? 1 : 0;
int bpp, mode_rate;
static int bws[2] = { DP_LINK_BW_1_62, DP_LINK_BW_2_7 };
+ int target_clock, link_avail, link_clock;
if (HAS_PCH_SPLIT(dev) && !IS_HASWELL(dev) && !is_cpu_edp(intel_dp))
pipe_config->has_pch_encoder = true;
@@ -755,6 +737,8 @@ intel_dp_compute_config(struct intel_encoder *encoder,
intel_connector->panel.fitting_mode,
mode, adjusted_mode);
}
+ /* We need to take the panel's fixed mode into account. */
+ target_clock = adjusted_mode->clock;
if (adjusted_mode->flags & DRM_MODE_FLAG_DBLCLK)
return false;
@@ -763,11 +747,31 @@ intel_dp_compute_config(struct intel_encoder *encoder,
"max bw %02x pixel clock %iKHz\n",
max_lane_count, bws[max_clock], adjusted_mode->clock);
- if (!intel_dp_adjust_dithering(intel_dp, adjusted_mode, true))
- return false;
+ /* Walk through all bpp values. Luckily they're all nicely space with 2
+ * bpc in between. */
+ bpp = 8*3;
+ if (is_edp(intel_dp))
+ bpp = min_t(int, bpp, dev_priv->edp.bpp);
+
+ for (; bpp >= 6*3; bpp -= 2*3) {
+ mode_rate = intel_dp_link_required(target_clock, bpp);
+
+ for (clock = 0; clock <= max_clock; clock++) {
+ for (lane_count = 1; lane_count <= max_lane_count; lane_count <<= 1) {
+ link_clock = drm_dp_bw_code_to_link_rate(bws[clock]);
+ link_avail = intel_dp_max_data_rate(link_clock,
+ lane_count);
+
+ if (mode_rate <= link_avail) {
+ goto found;
+ }
+ }
+ }
+ }
- bpp = adjusted_mode->private_flags & INTEL_MODE_DP_FORCE_6BPC ? 18 : 24;
+ return false;
+found:
if (intel_dp->color_range_auto) {
/*
* See:
@@ -783,31 +787,18 @@ intel_dp_compute_config(struct intel_encoder *encoder,
if (intel_dp->color_range)
adjusted_mode->private_flags |= INTEL_MODE_LIMITED_COLOR_RANGE;
- mode_rate = intel_dp_link_required(adjusted_mode->clock, bpp);
-
- for (clock = 0; clock <= max_clock; clock++) {
- for (lane_count = 1; lane_count <= max_lane_count; lane_count <<= 1) {
- int link_bw_clock =
- drm_dp_bw_code_to_link_rate(bws[clock]);
- int link_avail = intel_dp_max_data_rate(link_bw_clock,
- lane_count);
-
- if (mode_rate <= link_avail) {
- intel_dp->link_bw = bws[clock];
- intel_dp->lane_count = lane_count;
- adjusted_mode->clock = link_bw_clock;
- DRM_DEBUG_KMS("DP link bw %02x lane "
- "count %d clock %d bpp %d\n",
- intel_dp->link_bw, intel_dp->lane_count,
- adjusted_mode->clock, bpp);
- DRM_DEBUG_KMS("DP link bw required %i available %i\n",
- mode_rate, link_avail);
- return true;
- }
- }
- }
+ intel_dp->link_bw = bws[clock];
+ intel_dp->lane_count = lane_count;
+ adjusted_mode->clock = drm_dp_bw_code_to_link_rate(intel_dp->link_bw);
+ pipe_config->pipe_bpp = bpp;
- return false;
+ DRM_DEBUG_KMS("DP link bw %02x lane count %d clock %d bpp %d\n",
+ intel_dp->link_bw, intel_dp->lane_count,
+ adjusted_mode->clock, bpp);
+ DRM_DEBUG_KMS("DP link bw required %i available %i\n",
+ mode_rate, link_avail);
+
+ return true;
}
void
diff --git a/drivers/gpu/drm/i915/intel_drv.h b/drivers/gpu/drm/i915/intel_drv.h
index caebdae..341d117 100644
--- a/drivers/gpu/drm/i915/intel_drv.h
+++ b/drivers/gpu/drm/i915/intel_drv.h
@@ -101,12 +101,6 @@
#define INTEL_DVO_CHIP_TMDS 2
#define INTEL_DVO_CHIP_TVOUT 4
-/* drm_display_mode->private_flags */
-#define INTEL_MODE_DP_FORCE_6BPC (0x10)
-/*
- * Set when limited 16-235 (as opposed to full 0-255) RGB color range is
- * to be used.
- */
#define INTEL_MODE_LIMITED_COLOR_RANGE (0x40)
struct intel_framebuffer {
@@ -195,6 +189,8 @@ struct intel_crtc_config {
/* DP has a bunch of special case unfortunately, so mark the pipe
* accordingly. */
bool has_dp_encoder;
+ bool dither;
+ int pipe_bpp;
struct intel_link_m_n dp_m_n;
/* Used by SDVO (and if we ever fix it, HDMI). */
unsigned pixel_multiplier;
diff --git a/drivers/gpu/drm/i915/intel_hdmi.c b/drivers/gpu/drm/i915/intel_hdmi.c
index f6ba57b..48cb9f2 100644
--- a/drivers/gpu/drm/i915/intel_hdmi.c
+++ b/drivers/gpu/drm/i915/intel_hdmi.c
@@ -599,6 +599,9 @@ static void intel_hdmi_mode_set(struct drm_encoder *encoder,
struct intel_hdmi *intel_hdmi = enc_to_intel_hdmi(encoder);
u32 sdvox;
+ WARN_ON(intel_crtc->config.pipe_bpp != 8*3 &&
+ intel_crtc->config.pipe_bpp != 12*3);
+
sdvox = SDVO_ENCODING_HDMI;
if (!HAS_PCH_SPLIT(dev))
sdvox |= intel_hdmi->color_range;
@@ -794,6 +797,18 @@ bool intel_hdmi_compute_config(struct intel_encoder *encoder,
if (HAS_PCH_SPLIT(dev) && !IS_HASWELL(dev))
pipe_config->has_pch_encoder = true;
+ /*
+ * HDMI is either 12 or 8, so if the display lets 10bpc sneak
+ * through, clamp it down.
+ */
+ if (pipe_config->pipe_bpp > 8*3) {
+ DRM_DEBUG_KMS("forcing bpc to 12 for HDMI\n");
+ pipe_config->pipe_bpp = 12*3;
+ } else {
+ DRM_DEBUG_KMS("forcing bpc to 8 for HDMI\n");
+ pipe_config->pipe_bpp = 8*3;
+ }
+
return true;
}
diff --git a/drivers/gpu/drm/i915/intel_lvds.c b/drivers/gpu/drm/i915/intel_lvds.c
index c0a1659..47ff403 100644
--- a/drivers/gpu/drm/i915/intel_lvds.c
+++ b/drivers/gpu/drm/i915/intel_lvds.c
@@ -310,6 +310,7 @@ static bool intel_lvds_compute_config(struct intel_encoder *intel_encoder,
struct drm_display_mode *mode = &pipe_config->requested_mode;
struct intel_crtc *intel_crtc = lvds_encoder->base.new_crtc;
u32 pfit_control = 0, pfit_pgm_ratios = 0, border = 0;
+ unsigned int lvds_bpp;
int pipe;
/* Should never happen!! */
@@ -321,6 +322,16 @@ static bool intel_lvds_compute_config(struct intel_encoder *intel_encoder,
if (intel_encoder_check_is_cloned(&lvds_encoder->base))
return false;
+ if (lvds_encoder->is_dual_link)
+ lvds_bpp = 8*3;
+ else
+ lvds_bpp = 6*3;
+
+ if (lvds_bpp != pipe_config->pipe_bpp) {
+ DRM_DEBUG_KMS("forcing display bpp (was %d) to LVDS (%d)\n",
+ pipe_config->pipe_bpp, lvds_bpp);
+ pipe_config->pipe_bpp = lvds_bpp;
+ }
/*
* We have timings from the BIOS for the panel, put them in
* to the adjusted mode. The CRTC will be set up for this mode,
--
1.7.11.7
More information about the Intel-gfx
mailing list