[Intel-gfx] [PATCH 5/7] drm/i915: store adjusted dotclock in adjusted_mode->clock
Paulo Zanoni
przanoni at gmail.com
Mon Jun 3 18:54:40 CEST 2013
2013/6/1 Daniel Vetter <daniel.vetter at ffwll.ch>:
> ... not the port clock. This allows us to kill the funny semantics
> around pixel_target_clock.
>
> Since the dpll code still needs the real port clock, add a new
> port_clock field to the pipe configuration. Handling the default case
> for that one is a bit tricky, since encoders might not consistently
> overwrite it when retrying the crtc/encoder bw arbitrage step in the
> compute config stage. Hence we need to always clear port_clock and
> update it again if the encoder hasn't put in something more specific.
> This can't be done in one step since the encoder might want to adjust
> the mode first.
>
> I was a bit on the fence whether I should subsume the pixel multiplier
> handling into the port_clock, too. But then I decided against this
> since it's on an abstract level still the dotclock of the adjusted
> mode, and only our hw makes it a bit special due to the separate pixel
> mulitplier setting (which requires that the dpll runs at the
> non-multiplied dotclock).
>
> So after this patch the adjusted_mode accurately describes the mode we
> feed into the port, after the panel fitter and pixel multiplier (or
> line doubling, if we ever bother with that) have done their job.
> Since the fdi link is between the pfit and the pixel multiplier steps
> we need to be careful with calculating the fdi link config.
>
> v2: Fix up ilk cpu pll handling.
>
> v3: Introduce an fdi_dotclock variable in ironlake_fdi_compute_config
> to make it clearer that we transmit the adjusted_mode without the
> pixel multiplier taken into account. The old code multiplied the the
> available link bw with the pixel multiplier, which results in the same
> fdi configuration, but is much more confusing.
>
> v4: Rebase on top of Imre's is_cpu_edp removal.
>
> v5: Rebase on top of Paulo's haswell watermark fixes, which introduce
> a new place which looked at the pixel_clock and so needed conversion.
>
> v6: Split out prep patches as requested by Paulo Zanoni. Also rebase
> on top of the fdi dotclock handling fix in the fdi lanes/bw
> computation code.
>
> Reviewed-by: Jesse Barnes <jbarnes at virtuousgeek.org> (v3)
> Signed-off-by: Daniel Vetter <daniel.vetter at ffwll.ch>
Due to my comments on patch 3, there's a possibility you may need to
rebase this patch.
My only optional bikeshed is to print port_clock inside
intel_dump_pipe_config. If you rebase, you may consider doing it :)
Reviewed-by: Paulo Zanoni <paulo.r.zanoni at intel.com> (v6)
> ---
> drivers/gpu/drm/i915/intel_ddi.c | 3 ++-
> drivers/gpu/drm/i915/intel_display.c | 32 +++++++++++++++++---------------
> drivers/gpu/drm/i915/intel_dp.c | 18 +++++++-----------
> drivers/gpu/drm/i915/intel_drv.h | 13 +++++++------
> drivers/gpu/drm/i915/intel_hdmi.c | 4 +---
> drivers/gpu/drm/i915/intel_pm.c | 5 +----
> 6 files changed, 35 insertions(+), 40 deletions(-)
>
> diff --git a/drivers/gpu/drm/i915/intel_ddi.c b/drivers/gpu/drm/i915/intel_ddi.c
> index 9649df8..486c46b 100644
> --- a/drivers/gpu/drm/i915/intel_ddi.c
> +++ b/drivers/gpu/drm/i915/intel_ddi.c
> @@ -624,7 +624,7 @@ intel_ddi_calculate_wrpll(int clock /* in Hz */,
> clock, *p_out, *n2_out, *r2_out);
> }
>
> -bool intel_ddi_pll_mode_set(struct drm_crtc *crtc, int clock)
> +bool intel_ddi_pll_mode_set(struct drm_crtc *crtc)
> {
> struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
> struct intel_encoder *intel_encoder = intel_ddi_get_crtc_encoder(crtc);
> @@ -634,6 +634,7 @@ bool intel_ddi_pll_mode_set(struct drm_crtc *crtc, int clock)
> int type = intel_encoder->type;
> enum pipe pipe = intel_crtc->pipe;
> uint32_t reg, val;
> + int clock = intel_crtc->config.port_clock;
>
> /* TODO: reuse PLLs when possible (compare values) */
>
> diff --git a/drivers/gpu/drm/i915/intel_display.c b/drivers/gpu/drm/i915/intel_display.c
> index 761254d..103f4e9 100644
> --- a/drivers/gpu/drm/i915/intel_display.c
> +++ b/drivers/gpu/drm/i915/intel_display.c
> @@ -3992,7 +3992,7 @@ static int ironlake_fdi_compute_config(struct intel_crtc *intel_crtc,
> {
> struct drm_device *dev = intel_crtc->base.dev;
> struct drm_display_mode *adjusted_mode = &pipe_config->adjusted_mode;
> - int target_clock, lane, link_bw, fdi_dotclock;
> + int lane, link_bw, fdi_dotclock;
> bool setup_ok, needs_recompute = false;
>
> retry:
> @@ -4005,12 +4005,7 @@ retry:
> */
> link_bw = intel_fdi_link_freq(dev) * MHz(100)/KHz(1)/10;
>
> - if (pipe_config->pixel_target_clock)
> - target_clock = pipe_config->pixel_target_clock;
> - else
> - target_clock = adjusted_mode->clock;
> -
> - fdi_dotclock = target_clock;
> + fdi_dotclock = adjusted_mode->clock;
In the patch you sent Friday, you used adjusted_mode->clock instead of
fdi_dotclock as the parameter to ironlake_get_lanes_required, you only
initialized fdi_dotclock before calling intel_link_compute_m_n. This
doesn't change the code behavior, I'm just pointing in case you
changed without noticing and prefer the older version.
> if (pipe_config->pixel_multiplier > 1)
> fdi_dotclock /= pipe_config->pixel_multiplier;
>
> @@ -4360,8 +4355,6 @@ static void vlv_update_pll(struct intel_crtc *crtc)
> {
> struct drm_device *dev = crtc->base.dev;
> struct drm_i915_private *dev_priv = dev->dev_private;
> - struct drm_display_mode *adjusted_mode =
> - &crtc->config.adjusted_mode;
> struct intel_encoder *encoder;
> int pipe = crtc->pipe;
> u32 dpll, mdiv;
> @@ -4414,7 +4407,7 @@ static void vlv_update_pll(struct intel_crtc *crtc)
> vlv_dpio_write(dev_priv, DPIO_DIV(pipe), mdiv);
>
> /* Set HBR and RBR LPF coefficients */
> - if (adjusted_mode->clock == 162000 ||
> + if (crtc->config.port_clock == 162000 ||
> intel_pipe_has_type(&crtc->base, INTEL_OUTPUT_HDMI))
> vlv_dpio_write(dev_priv, DPIO_LFP_COEFF(pipe),
> 0x005f0021);
> @@ -4859,7 +4852,8 @@ static int i9xx_crtc_mode_set(struct drm_crtc *crtc,
> * reflck * (5 * (m1 + 2) + (m2 + 2)) / (n + 2) / p1 / p2.
> */
> limit = intel_limit(crtc, refclk);
> - ok = dev_priv->display.find_dpll(limit, crtc, adjusted_mode->clock,
> + ok = dev_priv->display.find_dpll(limit, crtc,
> + intel_crtc->config.port_clock,
> refclk, NULL, &clock);
> if (!ok) {
> DRM_ERROR("Couldn't find PLL settings for mode!\n");
> @@ -5467,7 +5461,6 @@ static void haswell_set_pipeconf(struct drm_crtc *crtc)
> }
>
> static bool ironlake_compute_clocks(struct drm_crtc *crtc,
> - struct drm_display_mode *adjusted_mode,
> intel_clock_t *clock,
> bool *has_reduced_clock,
> intel_clock_t *reduced_clock)
> @@ -5495,7 +5488,8 @@ static bool ironlake_compute_clocks(struct drm_crtc *crtc,
> * reflck * (5 * (m1 + 2) + (m2 + 2)) / (n + 2) / p1 / p2.
> */
> limit = intel_limit(crtc, refclk);
> - ret = dev_priv->display.find_dpll(limit, crtc, adjusted_mode->clock,
> + ret = dev_priv->display.find_dpll(limit, crtc,
> + to_intel_crtc(crtc)->config.port_clock,
> refclk, NULL, clock);
> if (!ret)
> return false;
> @@ -5695,7 +5689,7 @@ static int ironlake_crtc_mode_set(struct drm_crtc *crtc,
> WARN(!(HAS_PCH_IBX(dev) || HAS_PCH_CPT(dev)),
> "Unexpected PCH type %d\n", INTEL_PCH_TYPE(dev));
>
> - ok = ironlake_compute_clocks(crtc, adjusted_mode, &clock,
> + ok = ironlake_compute_clocks(crtc, &clock,
> &has_reduced_clock, &reduced_clock);
> if (!ok) {
> DRM_ERROR("Couldn't find PLL settings for mode!\n");
> @@ -5898,7 +5892,7 @@ static int haswell_crtc_mode_set(struct drm_crtc *crtc,
> WARN(num_connectors != 1, "%d connectors attached to pipe %c\n",
> num_connectors, pipe_name(pipe));
>
> - if (!intel_ddi_pll_mode_set(crtc, adjusted_mode->clock))
> + if (!intel_ddi_pll_mode_set(crtc))
> return -EINVAL;
>
> /* Ensure that the cursor is valid for the new mode before changing... */
> @@ -7789,6 +7783,9 @@ intel_modeset_pipe_config(struct drm_crtc *crtc,
> goto fail;
>
> encoder_retry:
> + /* Ensure the port clock default is reset when retrying. */
> + pipe_config->port_clock = 0;
> +
> /* Pass our mode to the connectors and the CRTC to give them a chance to
> * adjust it according to limitations or connector properties, and also
> * a chance to reject the mode entirely.
> @@ -7817,6 +7814,11 @@ encoder_retry:
> }
> }
>
> + /* Set default port clock if not overwritten by the encoder. Needs to be
> + * done afterwards in case the encoder adjusts the mode. */
> + if (!pipe_config->port_clock)
> + pipe_config->port_clock = pipe_config->adjusted_mode.clock;
> +
> ret = intel_crtc_compute_config(crtc, pipe_config);
> if (ret < 0) {
> DRM_DEBUG_KMS("CRTC fixup failed\n");
> diff --git a/drivers/gpu/drm/i915/intel_dp.c b/drivers/gpu/drm/i915/intel_dp.c
> index 647cc2b..c92eeeb 100644
> --- a/drivers/gpu/drm/i915/intel_dp.c
> +++ b/drivers/gpu/drm/i915/intel_dp.c
> @@ -677,7 +677,7 @@ intel_dp_compute_config(struct intel_encoder *encoder,
> int max_clock = intel_dp_max_link_bw(intel_dp) == DP_LINK_BW_2_7 ? 1 : 0;
> int bpp, mode_rate;
> static int bws[2] = { DP_LINK_BW_1_62, DP_LINK_BW_2_7 };
> - int target_clock, link_avail, link_clock;
> + int link_avail, link_clock;
>
> if (HAS_PCH_SPLIT(dev) && !HAS_DDI(dev) && port != PORT_A)
> pipe_config->has_pch_encoder = true;
> @@ -694,8 +694,6 @@ intel_dp_compute_config(struct intel_encoder *encoder,
> intel_pch_panel_fitting(intel_crtc, pipe_config,
> intel_connector->panel.fitting_mode);
> }
> - /* We need to take the panel's fixed mode into account. */
> - target_clock = adjusted_mode->clock;
>
> if (adjusted_mode->flags & DRM_MODE_FLAG_DBLCLK)
> return false;
> @@ -711,7 +709,7 @@ intel_dp_compute_config(struct intel_encoder *encoder,
> bpp = min_t(int, bpp, dev_priv->vbt.edp_bpp);
>
> for (; bpp >= 6*3; bpp -= 2*3) {
> - mode_rate = intel_dp_link_required(target_clock, bpp);
> + mode_rate = intel_dp_link_required(adjusted_mode->clock, bpp);
>
> for (clock = 0; clock <= max_clock; clock++) {
> for (lane_count = 1; lane_count <= max_lane_count; lane_count <<= 1) {
> @@ -746,18 +744,17 @@ found:
>
> intel_dp->link_bw = bws[clock];
> intel_dp->lane_count = lane_count;
> - adjusted_mode->clock = drm_dp_bw_code_to_link_rate(intel_dp->link_bw);
> pipe_config->pipe_bpp = bpp;
> - pipe_config->pixel_target_clock = target_clock;
> + pipe_config->port_clock = drm_dp_bw_code_to_link_rate(intel_dp->link_bw);
>
> DRM_DEBUG_KMS("DP link bw %02x lane count %d clock %d bpp %d\n",
> intel_dp->link_bw, intel_dp->lane_count,
> - adjusted_mode->clock, bpp);
> + pipe_config->port_clock, bpp);
> DRM_DEBUG_KMS("DP link bw required %i available %i\n",
> mode_rate, link_avail);
>
> intel_link_compute_m_n(bpp, lane_count,
> - target_clock, adjusted_mode->clock,
> + adjusted_mode->clock, pipe_config->port_clock,
> &pipe_config->dp_m_n);
>
> intel_dp_set_clock(encoder, pipe_config, intel_dp->link_bw);
> @@ -788,12 +785,11 @@ static void ironlake_set_pll_cpu_edp(struct intel_dp *intel_dp)
> struct drm_i915_private *dev_priv = dev->dev_private;
> u32 dpa_ctl;
>
> - DRM_DEBUG_KMS("eDP PLL enable for clock %d\n",
> - crtc->config.adjusted_mode.clock);
> + DRM_DEBUG_KMS("eDP PLL enable for clock %d\n", crtc->config.port_clock);
> dpa_ctl = I915_READ(DP_A);
> dpa_ctl &= ~DP_PLL_FREQ_MASK;
>
> - if (crtc->config.adjusted_mode.clock == 162000) {
> + if (crtc->config.port_clock == 162000) {
> /* For a long time we've carried around a ILK-DevA w/a for the
> * 160MHz clock. If we're really unlucky, it's still required.
> */
> diff --git a/drivers/gpu/drm/i915/intel_drv.h b/drivers/gpu/drm/i915/intel_drv.h
> index fdf6303..afda71f 100644
> --- a/drivers/gpu/drm/i915/intel_drv.h
> +++ b/drivers/gpu/drm/i915/intel_drv.h
> @@ -243,12 +243,13 @@ struct intel_crtc_config {
>
> int pipe_bpp;
> struct intel_link_m_n dp_m_n;
> - /**
> - * This is currently used by DP and HDMI encoders since those can have a
> - * target pixel clock != the port link clock (which is currently stored
> - * in adjusted_mode->clock).
> +
> + /*
> + * Frequence the dpll for the port should run at. Differs from the
> + * adjusted dotclock e.g. for DP or 12bpc hdmi mode.
> */
> - int pixel_target_clock;
> + int port_clock;
> +
> /* Used by SDVO (and if we ever fix it, HDMI). */
> unsigned pixel_multiplier;
>
> @@ -786,7 +787,7 @@ extern void intel_ddi_disable_transcoder_func(struct drm_i915_private *dev_priv,
> extern void intel_ddi_enable_pipe_clock(struct intel_crtc *intel_crtc);
> extern void intel_ddi_disable_pipe_clock(struct intel_crtc *intel_crtc);
> extern void intel_ddi_setup_hw_pll_state(struct drm_device *dev);
> -extern bool intel_ddi_pll_mode_set(struct drm_crtc *crtc, int clock);
> +extern bool intel_ddi_pll_mode_set(struct drm_crtc *crtc);
> extern void intel_ddi_put_crtc_pll(struct drm_crtc *crtc);
> extern void intel_ddi_set_pipe_settings(struct drm_crtc *crtc);
> extern void intel_ddi_prepare_link_retrain(struct drm_encoder *encoder);
> diff --git a/drivers/gpu/drm/i915/intel_hdmi.c b/drivers/gpu/drm/i915/intel_hdmi.c
> index 8062a92..bc12518 100644
> --- a/drivers/gpu/drm/i915/intel_hdmi.c
> +++ b/drivers/gpu/drm/i915/intel_hdmi.c
> @@ -835,9 +835,7 @@ bool intel_hdmi_compute_config(struct intel_encoder *encoder,
> desired_bpp = 12*3;
>
> /* Need to adjust the port link by 1.5x for 12bpc. */
> - adjusted_mode->clock = clock_12bpc;
> - pipe_config->pixel_target_clock =
> - pipe_config->requested_mode.clock;
> + pipe_config->port_clock = clock_12bpc;
> } else {
> DRM_DEBUG_KMS("picking bpc to 8 for HDMI output\n");
> desired_bpp = 8*3;
> diff --git a/drivers/gpu/drm/i915/intel_pm.c b/drivers/gpu/drm/i915/intel_pm.c
> index 49a1887..4126fb1 100644
> --- a/drivers/gpu/drm/i915/intel_pm.c
> +++ b/drivers/gpu/drm/i915/intel_pm.c
> @@ -2078,10 +2078,7 @@ static uint32_t hsw_wm_get_pixel_rate(struct drm_device *dev,
> struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
> uint32_t pixel_rate, pfit_size;
>
> - if (intel_crtc->config.pixel_target_clock)
> - pixel_rate = intel_crtc->config.pixel_target_clock;
> - else
> - pixel_rate = intel_crtc->config.adjusted_mode.clock;
> + pixel_rate = intel_crtc->config.adjusted_mode.clock;
>
> /* We only use IF-ID interlacing. If we ever use PF-ID we'll need to
> * adjust the pixel_rate here. */
> --
> 1.7.11.7
>
--
Paulo Zanoni
More information about the Intel-gfx
mailing list