[Intel-gfx] [PATCH 3/5] drm/i915: properly set HSW WM_PIPE registers
Paulo Zanoni
przanoni at gmail.com
Sat May 25 00:00:42 CEST 2013
2013/5/24 Ville Syrjälä <ville.syrjala at linux.intel.com>:
> On Fri, May 24, 2013 at 11:59:19AM -0300, Paulo Zanoni wrote:
>> From: Paulo Zanoni <paulo.r.zanoni at intel.com>
>>
>> We were previously calling sandybridge_update_wm on HSW, but the SNB
>> function didn't really match the HSW specification, so we were just
>> writing the wrong values.
>>
>> With this patch, the haswell_update_wm function will set the correct
>> values for the WM_PIPE registers, but it will still keep all the LP
>> watermarks disabled.
>>
>> The patch may look a little bit over-complicated for now, but it's
>> because much of the infrastructure for setting the LP watermarks is
>> already in place, so we won't have too much code churn on the patch
>> that sets the LP watermarks.
>>
>> Signed-off-by: Paulo Zanoni <paulo.r.zanoni at intel.com>
>> ---
>> drivers/gpu/drm/i915/i915_reg.h | 3 +
>> drivers/gpu/drm/i915/intel_pm.c | 340 +++++++++++++++++++++++++++++++++++++---
>> 2 files changed, 325 insertions(+), 18 deletions(-)
>>
>> diff --git a/drivers/gpu/drm/i915/i915_reg.h b/drivers/gpu/drm/i915/i915_reg.h
>> index 55caedb..e86606c 100644
>> --- a/drivers/gpu/drm/i915/i915_reg.h
>> +++ b/drivers/gpu/drm/i915/i915_reg.h
>> @@ -4938,6 +4938,9 @@
>> #define SFUSE_STRAP_DDIC_DETECTED (1<<1)
>> #define SFUSE_STRAP_DDID_DETECTED (1<<0)
>>
>> +#define WM_MISC 0x45260
>> +#define WM_MISC_DATA_PARTITION_5_6 (1 << 0)
>> +
>> #define WM_DBG 0x45280
>> #define WM_DBG_DISALLOW_MULTIPLE_LP (1<<0)
>> #define WM_DBG_DISALLOW_MAXFIFO (1<<1)
>> diff --git a/drivers/gpu/drm/i915/intel_pm.c b/drivers/gpu/drm/i915/intel_pm.c
>> index 0b61a0e..2ee1d01 100644
>> --- a/drivers/gpu/drm/i915/intel_pm.c
>> +++ b/drivers/gpu/drm/i915/intel_pm.c
>> @@ -2072,19 +2072,173 @@ static void ivybridge_update_wm(struct drm_device *dev)
>> cursor_wm);
>> }
>>
>> -static void
>> -haswell_update_linetime_wm(struct drm_device *dev, struct drm_crtc *crtc)
>> +static uint32_t hsw_wm_get_pixel_rate(struct drm_device *dev,
>> + struct drm_crtc *crtc)
>> +{
>> + struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
>> + uint32_t pixel_rate, pfit_size;
>> +
>> + if (intel_crtc->config.pixel_target_clock)
>> + pixel_rate = intel_crtc->config.pixel_target_clock;
>> + else
>> + pixel_rate = intel_crtc->config.adjusted_mode.clock;
>> +
>> + /* We only use IF-ID interlacing. If we ever use PF-ID we'll need to
>> + * adjust the pixel_rate here. */
>> +
>> + pfit_size = intel_crtc->config.pch_pfit.size;
>> + if (pfit_size) {
>> + uint64_t x, y, crtc_x, crtc_y, hscale, vscale, totscale;
>> +
>> + x = (pfit_size >> 16) & 0xFFFF;
>> + y = pfit_size & 0xFFFF;
>> + crtc_x = intel_crtc->config.adjusted_mode.hdisplay;
>> + crtc_y = intel_crtc->config.adjusted_mode.vdisplay;
>> +
>> + hscale = crtc_x << 16;
>> + vscale = crtc_y << 16;
>> + do_div(hscale, x);
>> + do_div(vscale, y);
>> + hscale = (hscale < (1 << 16)) ? (1 << 16) : hscale;
>> + vscale = (vscale < (1 << 16)) ? (1 << 16) : vscale;
>> + totscale = (hscale * vscale) >> 16;
>> + pixel_rate = (pixel_rate * totscale) >> 16;
>
> No need for fixed point math if you go 64bits, and as stated before
> the scaling ratio is still being miscaclulated due to the use of
> adjusted_mode.
>
> Something like this ought to do it:
>
> in_w = req_mode.hdisplay;
> in_h = req_mode.vdisplay;
> out_w = (pfit_size >> 16) & 0xffff;
> out_h = pfit_size & 0xffff;
> if (in_w <= out_w)
> in_w = out_w;
> if (in_h <= out_h)
> in_h = out_h;
>
> pixel_rate = div_u64((uint64_t) pixel_rate * in_w * in_h, out_w * out_h);
Ok, I re-checked and you were right. Fixed. Sorry for insisting :(
>
>> + }
>> +
>> + return pixel_rate;
>> +}
>> +
>> +static uint32_t hsw_wm_method1(uint32_t pixel_rate, uint8_t bytes_per_pixel,
>> + uint32_t latency)
>> +{
>> + uint64_t tmp;
>> + uint32_t ret;
>> +
>> + tmp = pixel_rate * bytes_per_pixel * latency;
>
> Would need a cast to make the multiplications actually 64bit. 'ret' is
> also pointless.
Oops... Fixed.
>
>> + ret = DIV_ROUND_UP_ULL(tmp, 64 * 10000) + 2;
>> +
>> + return ret;
>> +}
>> +
>> +static uint32_t hsw_wm_method2(uint32_t pixel_rate, uint32_t pipe_htotal,
>> + uint32_t horiz_pixels, uint8_t bytes_per_pixel,
>> + uint32_t latency)
>> +{
>> + uint32_t ret;
>> +
>> + ret = DIV_ROUND_UP(pipe_htotal * 1000, pixel_rate);
>> + ret = ((latency / (ret * 10)) + 1) * horiz_pixels * bytes_per_pixel;
>
> w/ 64bit maths this could be:
>
> tmp = (uint64_t) latency * pixel_rate * 100;
> ret = (div_u64(tmp, pipe_htotal) + 1) * horiz_pixels * bytes_per_pixel
I did the math on a paper and your formula doesn't look correct. For
latency=10 rate=120000 pipe_htotal=2000 horiz_pixels=1500 bpp=4 the
correct value should be 96, but your formula gives me a really huge
value. Besides, I like having the formula match BSpec exactly. And I
can't see how the current code would give us overflows, that's why I
kept it using uint32_t.
>
>> + ret = DIV_ROUND_UP(ret, 64) + 2;
>> + return ret;
>> +}
>> +
>> +struct hsw_pipe_wm_parameters {
>> + bool active;
>> + bool sprite_enabled;
>> + uint8_t pri_bytes_per_pixel;
>> + uint8_t spr_bytes_per_pixel;
>> + uint8_t cur_bytes_per_pixel;
>> + uint32_t pri_horiz_pixels;
>> + uint32_t spr_horiz_pixels;
>> + uint32_t cur_horiz_pixels;
>> + uint32_t pipe_htotal;
>> + uint32_t pixel_rate;
>> +};
>> +
>> +struct hsw_wm_values {
>> + uint32_t wm_pipe[3];
>> + uint32_t wm_lp[3];
>> + uint32_t wm_lp_spr[3];
>> + uint32_t wm_linetime[3];
>> +};
>> +
>> +enum hsw_data_buf_partitioning {
>> + HSW_DATA_BUF_PART_1_2,
>> + HSW_DATA_BUF_PART_5_6,
>> +};
>> +
>> +/* Only for WM_PIPE. */
>> +static uint32_t hsw_compute_pri_wm_pipe(struct hsw_pipe_wm_parameters *params,
>> + uint32_t mem_value)
>> +{
>> + /* TODO: for now, assume the primary plane is always enabled. */
>> + if (!params->active)
>> + return 0;
>> +
>> + return hsw_wm_method1(params->pixel_rate,
>> + params->pri_bytes_per_pixel,
>> + mem_value);
>> +}
>> +
>> +/* For both WM_PIPE and WM_LP. */
>> +static uint32_t hsw_compute_spr_wm(struct hsw_pipe_wm_parameters *params,
>> + uint32_t mem_value)
>> +{
>> + uint32_t method1, method2;
>> +
>> + if (!params->active || !params->sprite_enabled)
>> + return 0;
>> +
>> + method1 = hsw_wm_method1(params->pixel_rate,
>> + params->spr_bytes_per_pixel,
>> + mem_value);
>> + method2 = hsw_wm_method2(params->pixel_rate,
>> + params->pipe_htotal,
>> + params->spr_horiz_pixels,
>> + params->spr_bytes_per_pixel,
>> + mem_value);
>> + return min(method1, method2);
>> +}
>> +
>> +/* For both WM_PIPE and WM_LP. */
>> +static uint32_t hsw_compute_cur_wm(struct hsw_pipe_wm_parameters *params,
>> + uint32_t mem_value)
>> +{
>> + if (!params->active)
>> + return 0;
>> +
>> + return hsw_wm_method2(params->pixel_rate,
>> + params->pipe_htotal,
>> + params->cur_horiz_pixels,
>> + params->cur_bytes_per_pixel,
>> + mem_value);
>> +}
>> +
>> +static uint32_t hsw_compute_wm_pipe(struct drm_i915_private *dev_priv,
>> + uint32_t mem_value, enum pipe pipe,
>> + struct hsw_pipe_wm_parameters *params)
>> +{
>> + uint32_t pri_val, cur_val, spr_val;
>> +
>> + pri_val = hsw_compute_pri_wm_pipe(params, mem_value);
>> + spr_val = hsw_compute_spr_wm(params, mem_value);
>> + cur_val = hsw_compute_cur_wm(params, mem_value);
>> +
>> + WARN(pri_val > 127,
>> + "Primary WM error, mode not supported for pipe %c\n",
>> + pipe_name(pipe));
>> + WARN(spr_val > 127,
>> + "Sprite WM error, mode not supported for pipe %c\n",
>> + pipe_name(pipe));
>> + WARN(cur_val > 63,
>> + "Cursor WM error, mode not supported for pipe %c\n",
>> + pipe_name(pipe));
>> +
>> + return (pri_val << WM0_PIPE_PLANE_SHIFT) |
>> + (spr_val << WM0_PIPE_SPRITE_SHIFT) |
>> + cur_val;
>> +}
>> +
>> +static uint32_t
>> +hsw_compute_linetime_wm(struct drm_device *dev, struct drm_crtc *crtc)
>> {
>> struct drm_i915_private *dev_priv = dev->dev_private;
>> struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
>> - enum pipe pipe = intel_crtc->pipe;
>> struct drm_display_mode *mode = &intel_crtc->config.adjusted_mode;
>> u32 linetime, ips_linetime;
>>
>> - if (!intel_crtc_active(crtc)) {
>> - I915_WRITE(PIPE_WM_LINETIME(pipe), 0);
>> - return;
>> - }
>> + if (!intel_crtc_active(crtc))
>> + return 0;
>>
>> /* The WM are computed with base on how long it takes to fill a single
>> * row at the given clock rate, multiplied by 8.
>> @@ -2093,29 +2247,179 @@ haswell_update_linetime_wm(struct drm_device *dev, struct drm_crtc *crtc)
>> ips_linetime = DIV_ROUND_CLOSEST(mode->htotal * 1000 * 8,
>> intel_ddi_get_cdclk_freq(dev_priv));
>>
>> - I915_WRITE(PIPE_WM_LINETIME(pipe),
>> - PIPE_WM_LINETIME_IPS_LINETIME(ips_linetime) |
>> - PIPE_WM_LINETIME_TIME(linetime));
>> + return PIPE_WM_LINETIME_IPS_LINETIME(ips_linetime) |
>> + PIPE_WM_LINETIME_TIME(linetime);
>> }
>>
>> -static void haswell_update_wm(struct drm_device *dev)
>> +static void hsw_compute_wm_parameters(struct drm_device *dev,
>> + struct hsw_pipe_wm_parameters *params,
>> + uint32_t *wm)
>> {
>> struct drm_i915_private *dev_priv = dev->dev_private;
>> struct drm_crtc *crtc;
>> + struct drm_plane *plane;
>> + uint64_t sskpd = I915_READ64(MCH_SSKPD);
>> enum pipe pipe;
>>
>> - /* Disable the LP WMs before changine the linetime registers. This is
>> - * just a temporary code that will be replaced soon. */
>> - I915_WRITE(WM3_LP_ILK, 0);
>> - I915_WRITE(WM2_LP_ILK, 0);
>> - I915_WRITE(WM1_LP_ILK, 0);
>> + if ((sskpd >> 56) & 0xFF)
>> + wm[0] = (sskpd >> 56) & 0xFF;
>> + else
>> + wm[0] = sskpd & 0xF;
>> + wm[1] = ((sskpd >> 4) & 0xFF) * 5;
>> + wm[2] = ((sskpd >> 12) & 0xFF) * 5;
>> + wm[3] = ((sskpd >> 20) & 0x1FF) * 5;
>> + wm[4] = ((sskpd >> 32) & 0x1FF) * 5;
>> +
>> + list_for_each_entry(crtc, &dev->mode_config.crtc_list, head) {
>> + struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
>> + struct hsw_pipe_wm_parameters *p;
>> +
>> + pipe = intel_crtc->pipe;
>> + p = ¶ms[pipe];
>> +
>> + p->active = intel_crtc_active(crtc);
>> + if (!p->active)
>> + continue;
>> +
>> + p->pipe_htotal = intel_crtc->config.adjusted_mode.htotal;
>> + p->pixel_rate = hsw_wm_get_pixel_rate(dev, crtc);
>> + p->pri_bytes_per_pixel = crtc->fb->bits_per_pixel / 8;
>> + p->cur_bytes_per_pixel = 4;
>> + p->pri_horiz_pixels = intel_crtc->config.adjusted_mode.hdisplay;
>> + p->cur_horiz_pixels = 64;
>> + }
>> +
>> + list_for_each_entry(plane, &dev->mode_config.plane_list, head) {
>> + struct intel_plane *intel_plane = to_intel_plane(plane);
>> + struct hsw_pipe_wm_parameters *p;
>> +
>> + pipe = intel_plane->pipe;
>> + p = ¶ms[pipe];
>> +
>> + p->sprite_enabled = intel_plane->wm.enable;
>> + p->spr_bytes_per_pixel = intel_plane->wm.bytes_per_pixel;
>> + p->spr_horiz_pixels = intel_plane->wm.horiz_pixels;
>> + }
>> +}
>> +
>> +static void hsw_compute_wm_results(struct drm_device *dev,
>> + struct hsw_pipe_wm_parameters *params,
>> + uint32_t *wm,
>> + struct hsw_wm_values *results)
>> +{
>> + struct drm_i915_private *dev_priv = dev->dev_private;
>> + struct drm_crtc *crtc;
>> + enum pipe pipe;
>> +
>> + /* No support for LP WMs yet. */
>> + results->wm_lp[2] = 0;
>> + results->wm_lp[1] = 0;
>> + results->wm_lp[0] = 0;
>> + results->wm_lp_spr[2] = 0;
>> + results->wm_lp_spr[1] = 0;
>> + results->wm_lp_spr[0] = 0;
>> +
>> + for_each_pipe(pipe)
>> + results->wm_pipe[pipe] = hsw_compute_wm_pipe(dev_priv, wm[0],
>> + pipe,
>> + ¶ms[pipe]);
>>
>> for_each_pipe(pipe) {
>> crtc = dev_priv->pipe_to_crtc_mapping[pipe];
>> - haswell_update_linetime_wm(dev, crtc);
>> + results->wm_linetime[pipe] = hsw_compute_linetime_wm(dev, crtc);
>> }
>> +}
>> +
>> +/*
>> + * The spec says we shouldn't write when we don't need, because every write
>> + * causes WMs to be re-evaluated, expending some power.
>> + */
>> +static void hsw_write_wm_values(struct drm_i915_private *dev_priv,
>> + struct hsw_wm_values *results,
>> + enum hsw_data_buf_partitioning partitioning)
>> +{
>> + struct hsw_wm_values previous;
>> + uint32_t val;
>> + enum hsw_data_buf_partitioning prev_partitioning;
>> +
>> + previous.wm_pipe[0] = I915_READ(WM0_PIPEA_ILK);
>> + previous.wm_pipe[1] = I915_READ(WM0_PIPEB_ILK);
>> + previous.wm_pipe[2] = I915_READ(WM0_PIPEC_IVB);
>> + previous.wm_lp[0] = I915_READ(WM1_LP_ILK);
>> + previous.wm_lp[1] = I915_READ(WM2_LP_ILK);
>> + previous.wm_lp[2] = I915_READ(WM3_LP_ILK);
>> + previous.wm_lp_spr[0] = I915_READ(WM1S_LP_ILK);
>> + previous.wm_lp_spr[1] = I915_READ(WM2S_LP_IVB);
>> + previous.wm_lp_spr[2] = I915_READ(WM3S_LP_IVB);
>> + previous.wm_linetime[0] = I915_READ(PIPE_WM_LINETIME(PIPE_A));
>> + previous.wm_linetime[1] = I915_READ(PIPE_WM_LINETIME(PIPE_B));
>> + previous.wm_linetime[2] = I915_READ(PIPE_WM_LINETIME(PIPE_C));
>> +
>> + prev_partitioning = (I915_READ(WM_MISC) & WM_MISC_DATA_PARTITION_5_6) ?
>> + HSW_DATA_BUF_PART_5_6 : HSW_DATA_BUF_PART_1_2;
>> +
>> + if (memcmp(results->wm_pipe, previous.wm_pipe, 3) == 0 &&
>> + memcmp(results->wm_lp, previous.wm_lp, 3) == 0 &&
>> + memcmp(results->wm_lp_spr, previous.wm_lp_spr, 3) == 0 &&
>> + memcmp(results->wm_linetime, previous.wm_linetime, 3) == 0 &&
>> + partitioning == prev_partitioning)
>> + return;
>> +
>> + if (previous.wm_lp[2] != 0)
>> + I915_WRITE(WM3_LP_ILK, 0);
>> + if (previous.wm_lp[1] != 0)
>> + I915_WRITE(WM2_LP_ILK, 0);
>> + if (previous.wm_lp[0] != 0)
>> + I915_WRITE(WM1_LP_ILK, 0);
>
> I don't know if this conditional writing makes sense in such a fine
> granularity. We're anyway going to write some of the registeres, so
> maybe it's better to just go ahead and write all of them. It would
> at least make the code look a bit better.
The documentation says "Do not write the watermark registers when
there is no need to change a value, as every write will cause the
watermarks to be re-evaluated, expending some power.". I do recognize
the function looks a little bit ugly, but I think it's worth the cost,
especially since I imagine we're not going to change it too much in
the future.
>
> In any case you'd at least need to make sure that you disable/re-enable
> the LP1+ watermarks if linetime WMs or DDB partitioning changes,
> regardless of whether the LP1+ watermarks themselves changed.
We already do this.
Thanks again for the review,
Paulo
>
>> +
>> + if (previous.wm_pipe[0] != results->wm_pipe[0])
>> + I915_WRITE(WM0_PIPEA_ILK, results->wm_pipe[0]);
>> + if (previous.wm_pipe[1] != results->wm_pipe[1])
>> + I915_WRITE(WM0_PIPEB_ILK, results->wm_pipe[1]);
>> + if (previous.wm_pipe[2] != results->wm_pipe[2])
>> + I915_WRITE(WM0_PIPEC_IVB, results->wm_pipe[2]);
>> +
>> + if (previous.wm_linetime[0] != results->wm_linetime[0])
>> + I915_WRITE(PIPE_WM_LINETIME(PIPE_A), results->wm_linetime[0]);
>> + if (previous.wm_linetime[1] != results->wm_linetime[1])
>> + I915_WRITE(PIPE_WM_LINETIME(PIPE_B), results->wm_linetime[1]);
>> + if (previous.wm_linetime[2] != results->wm_linetime[2])
>> + I915_WRITE(PIPE_WM_LINETIME(PIPE_C), results->wm_linetime[2]);
>> +
>> + if (prev_partitioning != partitioning) {
>> + val = I915_READ(WM_MISC);
>> + if (partitioning == HSW_DATA_BUF_PART_1_2)
>> + val &= ~WM_MISC_DATA_PARTITION_5_6;
>> + else
>> + val |= WM_MISC_DATA_PARTITION_5_6;
>> + I915_WRITE(WM_MISC, val);
>> + }
>> +
>> + if (previous.wm_lp_spr[0] != results->wm_lp_spr[0])
>> + I915_WRITE(WM1S_LP_ILK, results->wm_lp_spr[0]);
>> + if (previous.wm_lp_spr[1] != results->wm_lp_spr[1])
>> + I915_WRITE(WM2S_LP_IVB, results->wm_lp_spr[1]);
>> + if (previous.wm_lp_spr[2] != results->wm_lp_spr[2])
>> + I915_WRITE(WM3S_LP_IVB, results->wm_lp_spr[2]);
>> +
>> + if (results->wm_lp[0] != 0)
>> + I915_WRITE(WM1_LP_ILK, results->wm_lp[0]);
>> + if (results->wm_lp[1] != 0)
>> + I915_WRITE(WM2_LP_ILK, results->wm_lp[1]);
>> + if (results->wm_lp[2] != 0)
>> + I915_WRITE(WM3_LP_ILK, results->wm_lp[2]);
>> +}
>> +
>> +static void haswell_update_wm(struct drm_device *dev)
>> +{
>> + struct drm_i915_private *dev_priv = dev->dev_private;
>> + struct hsw_pipe_wm_parameters params[3];
>> + struct hsw_wm_values results;
>> + uint32_t wm[5];
>>
>> - sandybridge_update_wm(dev);
>> + hsw_compute_wm_parameters(dev, params, wm);
>> + hsw_compute_wm_results(dev, params, wm, &results);
>> + hsw_write_wm_values(dev_priv, &results, HSW_DATA_BUF_PART_1_2);
>> }
>>
>> static void haswell_update_sprite_wm(struct drm_device *dev, int pipe,
>> --
>> 1.8.1.2
>>
>> _______________________________________________
>> Intel-gfx mailing list
>> Intel-gfx at lists.freedesktop.org
>> http://lists.freedesktop.org/mailman/listinfo/intel-gfx
>
> --
> Ville Syrjälä
> Intel OTC
--
Paulo Zanoni
More information about the Intel-gfx
mailing list