[Intel-gfx] [PATCH 22/40] drm/i915: Add chv port D TX wells

[Ville Syrjälä]

On Fri, Jul 25, 2014 at 04:30:29PM +0300, Imre Deak wrote:
> On Sat, 2014-06-28 at 02:04 +0300, ville.syrjala at linux.intel.com wrote:
> > From: Ville Syrjälä <ville.syrjala at linux.intel.com>
> > 
> > Add the TX wells for port D. The Punit subsystem numbers are a total
> > guess at this time. Also I'm not sure these even exist. Certainly the
> > Punit in current hardware doesn't deal with these.
> > 
> > Signed-off-by: Ville Syrjälä <ville.syrjala at linux.intel.com>
> > ---
> >  drivers/gpu/drm/i915/i915_reg.h |  4 ++++
> >  drivers/gpu/drm/i915/intel_pm.c | 23 +++++++++++++++++++++++
> >  2 files changed, 27 insertions(+)
> > 
> > diff --git a/drivers/gpu/drm/i915/i915_reg.h b/drivers/gpu/drm/i915/i915_reg.h
> > index 3d1fef4..191df9e 100644
> > --- a/drivers/gpu/drm/i915/i915_reg.h
> > +++ b/drivers/gpu/drm/i915/i915_reg.h
> > @@ -525,6 +525,10 @@ enum punit_power_well {
> >  	PUNIT_POWER_WELL_DPIO_RX0		= 10,
> >  	PUNIT_POWER_WELL_DPIO_RX1		= 11,
> >  	PUNIT_POWER_WELL_DPIO_CMN_D		= 12,
> > +	/* FIXME: guesswork below */
> > +	PUNIT_POWER_WELL_DPIO_TX_D_LANES_01	= 13,
> > +	PUNIT_POWER_WELL_DPIO_TX_D_LANES_23	= 14,
> > +	PUNIT_POWER_WELL_DPIO_RX2		= 15,
> >  
> >  	PUNIT_POWER_WELL_NUM,
> >  };
> > diff --git a/drivers/gpu/drm/i915/intel_pm.c b/drivers/gpu/drm/i915/intel_pm.c
> > index cae936c..55f3e6b 100644
> > --- a/drivers/gpu/drm/i915/intel_pm.c
> > +++ b/drivers/gpu/drm/i915/intel_pm.c
> > @@ -6540,6 +6540,15 @@ EXPORT_SYMBOL_GPL(i915_release_power_well);
> >  	BIT(POWER_DOMAIN_PORT_DDI_D_4_LANES) |	\
> >  	BIT(POWER_DOMAIN_INIT))
> >  
> > +#define CHV_DPIO_TX_D_LANES_01_POWER_DOMAINS (	\
> > +	BIT(POWER_DOMAIN_PORT_DDI_D_2_LANES) |	\
> > +	BIT(POWER_DOMAIN_PORT_DDI_D_4_LANES) |	\
> > +	BIT(POWER_DOMAIN_INIT))
> > +
> > +#define CHV_DPIO_TX_D_LANES_23_POWER_DOMAINS (	\
> > +	BIT(POWER_DOMAIN_PORT_DDI_D_4_LANES) |	\
> 
> Atm, for all other ports we power up all lanes regardless of the actual
> configuration (until the PHY side setup is proved to work fine). So for
> consistency I'd do the same here too. With that change:

We do that here too. '.domains = 01 | 23' for both tx-d wells. Or am I
missing something?

> 
> Reviewed-by: Imre Deak <imre.deak at intel.com>
> 
> > +	BIT(POWER_DOMAIN_INIT))
> > +
> >  static const struct i915_power_well_ops i9xx_always_on_power_well_ops = {
> >  	.sync_hw = i9xx_always_on_power_well_noop,
> >  	.enable = i9xx_always_on_power_well_noop,
> > @@ -6757,6 +6766,20 @@ static struct i915_power_well chv_power_wells[] = {
> >  		.ops = &vlv_dpio_power_well_ops,
> >  		.data = PUNIT_POWER_WELL_DPIO_TX_C_LANES_23,
> >  	},
> > +	{
> > +		.name = "dpio-tx-d-01",
> > +		.domains = CHV_DPIO_TX_D_LANES_01_POWER_DOMAINS |
> > +			   CHV_DPIO_TX_D_LANES_23_POWER_DOMAINS,
> > +		.ops = &vlv_dpio_power_well_ops,
> > +		.data = PUNIT_POWER_WELL_DPIO_TX_D_LANES_01,
> > +	},
> > +	{
> > +		.name = "dpio-tx-d-23",
> > +		.domains = CHV_DPIO_TX_D_LANES_01_POWER_DOMAINS |
> > +			   CHV_DPIO_TX_D_LANES_23_POWER_DOMAINS,
> > +		.ops = &vlv_dpio_power_well_ops,
> > +		.data = PUNIT_POWER_WELL_DPIO_TX_D_LANES_23,
> > +	},
> >  #endif
> >  };
> >  
> 



-- 
Ville Syrjälä
Intel OTC