[Intel-gfx] [PATCH 1/3] drm/i915: add PWM and BLC assertion checks

[Jesse Barnes]

To make sure we properly follow the enable/disable sequences.

Signed-off-by: Jesse Barnes <jbarnes at virtuousgeek.org>
---
 drivers/gpu/drm/i915/intel_dp.c    | 62 ++++++++++++++++++++++++++++++++++++--
 drivers/gpu/drm/i915/intel_drv.h   |  1 +
 drivers/gpu/drm/i915/intel_panel.c |  5 ++-
 3 files changed, 65 insertions(+), 3 deletions(-)

diff --git a/drivers/gpu/drm/i915/intel_dp.c b/drivers/gpu/drm/i915/intel_dp.c
index bf73771..b6f7087 100644
--- a/drivers/gpu/drm/i915/intel_dp.c
+++ b/drivers/gpu/drm/i915/intel_dp.c
@@ -301,6 +301,20 @@ static u32 _pp_stat_reg(struct intel_dp *intel_dp)
 		return VLV_PIPE_PP_STATUS(vlv_power_sequencer_pipe(intel_dp));
 }
 
+static void assert_pwm(struct intel_connector *connector,
+		       bool expected_state)
+{
+	bool state;
+
+	state = intel_panel_get_backlight(connector);
+
+	WARN(state != expected_state, "pwm state failure, expected %d, found "
+	     "%d\n", expected_state, state);
+}
+
+#define assert_pwm_enabled(c) assert_pwm((c), true)
+#define assert_pwm_disabled(c) assert_pwm((c), false)
+
 static bool edp_have_panel_power(struct intel_dp *intel_dp)
 {
 	struct drm_device *dev = intel_dp_to_dev(intel_dp);
@@ -884,6 +898,8 @@ static void intel_dp_mode_set(struct intel_encoder *encoder)
 	struct intel_crtc *crtc = to_intel_crtc(encoder->base.crtc);
 	struct drm_display_mode *adjusted_mode = &crtc->config.adjusted_mode;
 
+	assert_pwm_disabled(intel_dp->attached_connector);
+
 	/*
 	 * There are four kinds of DP registers:
 	 *
@@ -1167,6 +1183,23 @@ static void edp_panel_vdd_off(struct intel_dp *intel_dp, bool sync)
 	}
 }
 
+/*
+ * For this and the disable sequence below, Google for actual eDP LCD timing
+ * diagrams or check the eDP spec.  Below is for reference on asserts and
+ * does not contain Tx values for delays between steps.
+ *
+ * For panel on, the sequence should be:
+ * - LCD power supply on (PP regs or VDD AUX)
+ *   - eDP should display black at this point
+ * - HPD (if present) should go high
+ * - AUX channel becomes available
+ * - link training begins
+ * - LED backlight power on
+ * - LED PWM_EN goes high, duty cycle >min (PWM regs)
+ * - link training completes
+ * - LED_EN goes high (PP BLC_EN bit)
+ */
+
 void intel_edp_panel_on(struct intel_dp *intel_dp)
 {
 	struct drm_device *dev = intel_dp_to_dev(intel_dp);
@@ -1212,6 +1245,19 @@ void intel_edp_panel_on(struct intel_dp *intel_dp)
 	}
 }
 
+/*
+ * For panel off the sequence should be:
+ * - LED_EN goes low (BLC_EN in our PP regs)
+ * - LED PWM_EN goes low (PWM duty cycle 0 and PWM enable = 0)
+ *   - eDP should display black video at this point
+ * - LED VCCS goes low (power for backlight)
+ * - DP link goes to idle or off
+ * - AUX goes down
+ * - HPD line (if present) drops to low
+ * - eDP black video stops
+ * - LCD power supply shuts down (PP regs and VDD AUX)
+ */
+
 void intel_edp_panel_off(struct intel_dp *intel_dp)
 {
 	struct intel_digital_port *intel_dig_port = dp_to_dig_port(intel_dp);
@@ -1231,11 +1277,17 @@ void intel_edp_panel_off(struct intel_dp *intel_dp)
 
 	WARN(!intel_dp->want_panel_vdd, "Need VDD to turn off panel\n");
 
+	/* By this time the PWM and BLC bits should be off already */
+	assert_pwm_disabled(intel_dp->attached_connector);
+
 	pp = ironlake_get_pp_control(intel_dp);
+
+	WARN(pp & EDP_BLC_ENABLE,
+	     "backlight controller still on at panel off time\n");
+
 	/* We need to switch off panel power _and_ force vdd, for otherwise some
 	 * panels get very unhappy and cease to work. */
-	pp &= ~(POWER_TARGET_ON | PANEL_POWER_RESET | EDP_FORCE_VDD |
-		EDP_BLC_ENABLE);
+	pp &= ~(POWER_TARGET_ON | PANEL_POWER_RESET | EDP_FORCE_VDD);
 
 	pp_ctrl_reg = _pp_ctrl_reg(intel_dp);
 
@@ -1271,6 +1323,9 @@ void intel_edp_backlight_on(struct intel_dp *intel_dp)
 	 * allowing it to appear.
 	 */
 	wait_backlight_on(intel_dp);
+
+	assert_pwm_enabled(intel_dp->attached_connector);
+
 	pp = ironlake_get_pp_control(intel_dp);
 	pp |= EDP_BLC_ENABLE;
 
@@ -1292,6 +1347,9 @@ void intel_edp_backlight_off(struct intel_dp *intel_dp)
 	if (!is_edp(intel_dp))
 		return;
 
+	/* PWM must still be enabled here */
+	assert_pwm_enabled(intel_dp->attached_connector);
+
 	intel_panel_disable_backlight(intel_dp->attached_connector);
 
 	DRM_DEBUG_KMS("\n");
diff --git a/drivers/gpu/drm/i915/intel_drv.h b/drivers/gpu/drm/i915/intel_drv.h
index 9002e77..0e91c40 100644
--- a/drivers/gpu/drm/i915/intel_drv.h
+++ b/drivers/gpu/drm/i915/intel_drv.h
@@ -861,6 +861,7 @@ void intel_gmch_panel_fitting(struct intel_crtc *crtc,
 			      int fitting_mode);
 void intel_panel_set_backlight(struct intel_connector *connector, u32 level,
 			       u32 max);
+u32 intel_panel_get_backlight(struct intel_connector *connector);
 int intel_panel_setup_backlight(struct drm_connector *connector);
 void intel_panel_enable_backlight(struct intel_connector *connector);
 void intel_panel_disable_backlight(struct intel_connector *connector);
diff --git a/drivers/gpu/drm/i915/intel_panel.c b/drivers/gpu/drm/i915/intel_panel.c
index cb05840..21c5e6f 100644
--- a/drivers/gpu/drm/i915/intel_panel.c
+++ b/drivers/gpu/drm/i915/intel_panel.c
@@ -384,6 +384,9 @@ static u32 _vlv_get_backlight(struct drm_device *dev, enum pipe pipe)
 {
 	struct drm_i915_private *dev_priv = dev->dev_private;
 
+	if (I915_READ(VLV_BLC_PWM_CTL2(pipe) & BLM_PWM_ENABLE))
+		return 0;
+
 	return I915_READ(VLV_BLC_PWM_CTL(pipe)) & BACKLIGHT_DUTY_CYCLE_MASK;
 }
 
@@ -395,7 +398,7 @@ static u32 vlv_get_backlight(struct intel_connector *connector)
 	return _vlv_get_backlight(dev, pipe);
 }
 
-static u32 intel_panel_get_backlight(struct intel_connector *connector)
+u32 intel_panel_get_backlight(struct intel_connector *connector)
 {
 	struct drm_device *dev = connector->base.dev;
 	struct drm_i915_private *dev_priv = dev->dev_private;
-- 
1.8.4.2