[Intel-gfx] [PATCH 19/71] drm/i915/chv: Trigger phy common lane reset
Daniel Vetter
daniel at ffwll.ch
Mon May 12 19:27:48 CEST 2014
On Mon, Apr 28, 2014 at 05:54:24PM +0300, Imre Deak wrote:
> On Wed, 2014-04-09 at 13:28 +0300, ville.syrjala at linux.intel.com wrote:
> > From: Chon Ming Lee <chon.ming.lee at intel.com>
> >
> > During cold boot, the display controller needs to deassert the common
> > lane reset. Only do it once during intel_init_dpio for both PHYx2 and
> > PHYx1.
> >
> > Besides, assert the common lane reset when disable pll. This still
> > to be determined whether need to do it by driver.
> >
> > Signed-off-by: Chon Ming Lee <chon.ming.lee at intel.com>
> > [vsyrjala: Don't disable DPIO PLL when using DSI]
> > [vsyrjala: Don't call vlv_disable_pll() by accident on CHV]
> > Signed-off-by: Ville Syrjälä <ville.syrjala at linux.intel.com>
> > ---
> > drivers/gpu/drm/i915/i915_reg.h | 8 +++++
> > drivers/gpu/drm/i915/intel_display.c | 66 ++++++++++++++++++++++++++++--------
> > 2 files changed, 59 insertions(+), 15 deletions(-)
> >
> > diff --git a/drivers/gpu/drm/i915/i915_reg.h b/drivers/gpu/drm/i915/i915_reg.h
> > index 8aea092..8fcf4ea 100644
> > --- a/drivers/gpu/drm/i915/i915_reg.h
> > +++ b/drivers/gpu/drm/i915/i915_reg.h
> > @@ -1391,6 +1391,14 @@ enum punit_power_well {
> > /* Additional CHV pll/phy registers */
> > #define DPIO_PHY_STATUS (VLV_DISPLAY_BASE + 0x6240)
> > #define DPLL_PORTD_READY_MASK (0xf)
> > +#define DISPLAY_PHY_CONTROL (VLV_DISPLAY_BASE + 0x60100)
> > +#define PHY_COM_LANE_RESET_DEASSERT(phy, val) \
> > + ((phy == DPIO_PHY0) ? (val | 1) : (val | 2))
> > +#define PHY_COM_LANE_RESET_ASSERT(phy, val) \
> > + ((phy == DPIO_PHY0) ? (val & ~1) : (val & ~2))
> > +#define DISPLAY_PHY_STATUS (VLV_DISPLAY_BASE + 0x60104)
> > +#define PHY_POWERGOOD(phy) ((phy == DPIO_PHY0) ? (1<<31) : (1<<30))
> > +
> > /*
> > * The i830 generation, in LVDS mode, defines P1 as the bit number set within
> > * this field (only one bit may be set).
> > diff --git a/drivers/gpu/drm/i915/intel_display.c b/drivers/gpu/drm/i915/intel_display.c
> > index 153f244..e33667d 100644
> > --- a/drivers/gpu/drm/i915/intel_display.c
> > +++ b/drivers/gpu/drm/i915/intel_display.c
> > @@ -1395,17 +1395,36 @@ static void intel_reset_dpio(struct drm_device *dev)
> > DPLL_REFA_CLK_ENABLE_VLV |
> > DPLL_INTEGRATED_CRI_CLK_VLV);
> >
> > - /*
> > - * From VLV2A0_DP_eDP_DPIO_driver_vbios_notes_10.docx -
> > - * 6. De-assert cmn_reset/side_reset. Same as VLV X0.
> > - * a. GUnit 0x2110 bit[0] set to 1 (def 0)
> > - * b. The other bits such as sfr settings / modesel may all be set
> > - * to 0.
>
> This is VLV specific, so ok to be moved,
>
> > - *
> > - * This should only be done on init and resume from S3 with both
> > - * PLLs disabled, or we risk losing DPIO and PLL synchronization.
> > - */
>
> but this is also true for CHV, so should stay.
I've copypasted this block to the chv comment while merging.
-Daniel
>
> > - I915_WRITE(DPIO_CTL, I915_READ(DPIO_CTL) | DPIO_CMNRST);
> > + if (IS_CHERRYVIEW(dev)) {
> > + enum dpio_phy phy;
> > + u32 val;
> > +
> > + for (phy = DPIO_PHY0; phy < I915_NUM_PHYS_VLV; phy++) {
> > + /* Poll for phypwrgood signal */
> > + if (wait_for(I915_READ(DISPLAY_PHY_STATUS) &
> > + PHY_POWERGOOD(phy), 1))
> > + DRM_ERROR("Display PHY %d is not power up\n", phy);
> > +
> > + /* Deassert common lane reset for PHY*/
> > + val = I915_READ(DISPLAY_PHY_CONTROL);
> > + I915_WRITE(DISPLAY_PHY_CONTROL,
> > + PHY_COM_LANE_RESET_DEASSERT(phy, val));
>
> Would be clearer not to hide the 'or' in the macro and let
> PHY_COM_LANE_RESET_DEASSERT be just the flag itself and do here
> I915_WRITE(DISPLAY_PHY_CONTROL, val | PHY_COM_LANE_RESET_DEASSERT(phy));
>
> The above issues are minor, so even without fixing them this patch is
> Reviewed-by: Imre Deak <imre.deak at intel.com>
>
> > + }
> > +
> > + } else {
> > + /*
> > + * From VLV2A0_DP_eDP_DPIO_driver_vbios_notes_10.docx -
> > + * 6. De-assert cmn_reset/side_reset. Same as VLV X0.
> > + * a. GUnit 0x2110 bit[0] set to 1 (def 0)
> > + * b. The other bits such as sfr settings / modesel may all
> > + * be set to 0.
> > + *
> > + * This should only be done on init and resume from S3 with
> > + * both PLLs disabled, or we risk losing DPIO and PLL
> > + * synchronization.
> > + */
> > + I915_WRITE(DPIO_CTL, I915_READ(DPIO_CTL) | DPIO_CMNRST);
> > + }
> > }
> >
> > static void vlv_enable_pll(struct intel_crtc *crtc)
> > @@ -1529,6 +1548,19 @@ static void vlv_disable_pll(struct drm_i915_private *dev_priv, enum pipe pipe)
> > val = DPLL_INTEGRATED_CRI_CLK_VLV | DPLL_REFA_CLK_ENABLE_VLV;
> > I915_WRITE(DPLL(pipe), val);
> > POSTING_READ(DPLL(pipe));
> > +
> > +}
> > +
> > +static void chv_disable_pll(struct drm_i915_private *dev_priv, enum pipe pipe)
> > +{
> > + int dpll = DPLL(pipe);
> > + u32 val;
> > +
> > + /* Set PLL en = 0 */
> > + val = I915_READ(dpll);
> > + val &= ~DPLL_VCO_ENABLE;
> > + I915_WRITE(dpll, val);
> > +
> > }
> >
> > void vlv_wait_port_ready(struct drm_i915_private *dev_priv,
> > @@ -4511,10 +4543,14 @@ static void i9xx_crtc_disable(struct drm_crtc *crtc)
> > if (encoder->post_disable)
> > encoder->post_disable(encoder);
> >
> > - if (IS_VALLEYVIEW(dev) && !intel_pipe_has_type(crtc, INTEL_OUTPUT_DSI))
> > - vlv_disable_pll(dev_priv, pipe);
> > - else if (!IS_VALLEYVIEW(dev))
> > - i9xx_disable_pll(dev_priv, pipe);
> > + if (!intel_pipe_has_type(crtc, INTEL_OUTPUT_DSI)) {
> > + if (IS_CHERRYVIEW(dev))
> > + chv_disable_pll(dev_priv, pipe);
> > + else if (IS_VALLEYVIEW(dev))
> > + vlv_disable_pll(dev_priv, pipe);
> > + else
> > + i9xx_disable_pll(dev_priv, pipe);
> > + }
> >
> > intel_crtc->active = false;
> > intel_update_watermarks(crtc);
>
> _______________________________________________
> Intel-gfx mailing list
> Intel-gfx at lists.freedesktop.org
> http://lists.freedesktop.org/mailman/listinfo/intel-gfx
--
Daniel Vetter
Software Engineer, Intel Corporation
+41 (0) 79 365 57 48 - http://blog.ffwll.ch
More information about the Intel-gfx
mailing list