[Intel-gfx] [PATCH 5/8] drm/i915: Add the display switch logic for vgpu in i915 driver

[Daniel Vetter]

On Sat, Sep 20, 2014 at 02:47:05AM +0800, Jike Song wrote:
> From: Yu Zhang <yu.c.zhang at intel.com>
> 
> Display switch logic is added to notify the vgt mediator that
> current vgpu have a valid surface to show. It does so by writing
> the display_ready field in PV INFO page, and then will be handled
> in vgt mediator. This is useful to avoid trickiness when the VM's
> framebuffer is being accessed in the middle of VM modesetting,
> e.g. compositing the framebuffer in the host side
> 
> Signed-off-by: Yu Zhang <yu.c.zhang at intel.com>
> Signed-off-by: Jike Song <jike.song at intel.com>
> Signed-off-by: Zhiyuan Lv <zhiyuan.lv at intel.com>
> ---
>  drivers/gpu/drm/i915/i915_dma.c      |  8 ++++++++
>  drivers/gpu/drm/i915/i915_reg.h      |  7 +++++++
>  drivers/gpu/drm/i915/intel_display.c | 10 ++++++++++
>  3 files changed, 25 insertions(+)
> 
> diff --git a/drivers/gpu/drm/i915/i915_dma.c b/drivers/gpu/drm/i915/i915_dma.c
> index bb4ad52..d9462e1 100644
> --- a/drivers/gpu/drm/i915/i915_dma.c
> +++ b/drivers/gpu/drm/i915/i915_dma.c
> @@ -1790,6 +1790,14 @@ int i915_driver_load(struct drm_device *dev, unsigned long flags)
>  	} else {
>  		/* Start out suspended in ums mode. */
>  		dev_priv->ums.mm_suspended = 1;
> +		if (intel_vgpu_active(dev)) {
> +			/*
> +			 * Notify a valid surface after modesetting,
> +			 * when running inside a VM.
> +			 */
> +			I915_WRITE(vgt_info_off(display_ready),
> +				VGT_DRV_DISPLAY_READY);
> +		}
>  	}
>  
>  	i915_setup_sysfs(dev);
> diff --git a/drivers/gpu/drm/i915/i915_reg.h b/drivers/gpu/drm/i915/i915_reg.h
> index a70f12e..38d606c 100644
> --- a/drivers/gpu/drm/i915/i915_reg.h
> +++ b/drivers/gpu/drm/i915/i915_reg.h
> @@ -6673,5 +6673,12 @@ enum punit_power_well {
>  #define vgt_info_off(x) \
>  	(VGT_PVINFO_PAGE + (long)&((struct vgt_if *) NULL)->x)
>  
> +/*
> + * The information set by the guest gfx driver, through the display_ready field
> + */
> +enum vgt_display_status {
> +	VGT_DRV_DISPLAY_NOT_READY = 0,
> +	VGT_DRV_DISPLAY_READY,	/* ready for display switch */
> +};
>  
>  #endif /* _I915_REG_H_ */
> diff --git a/drivers/gpu/drm/i915/intel_display.c b/drivers/gpu/drm/i915/intel_display.c
> index b78f00a..3af9259 100644
> --- a/drivers/gpu/drm/i915/intel_display.c
> +++ b/drivers/gpu/drm/i915/intel_display.c
> @@ -11642,6 +11642,16 @@ static int intel_crtc_set_config(struct drm_mode_set *set)
>  			intel_modeset_check_state(set->crtc->dev);
>  	}
>  
> +	if (intel_vgpu_active(dev)) {
> +		/*
> +		 * Notify a valid surface after modesetting,
> +		 * when running inside a VM.
> +		 */
> +		struct drm_i915_private *dev_priv = dev->dev_private;
> +
> +		I915_WRITE(vgt_info_off(display_ready), VGT_DRV_DISPLAY_READY);
> +	}

Since very shortly we now have the frontbuffer tracking support code.
Should we move it there? See intel_frontbuffer_flush&flip.
-Daniel

> +
>  	if (ret) {
>  		DRM_DEBUG_KMS("failed to set mode on [CRTC:%d], err = %d\n",
>  			      set->crtc->base.id, ret);
> -- 
> 1.9.1
> 
> _______________________________________________
> Intel-gfx mailing list
> Intel-gfx at lists.freedesktop.org
> http://lists.freedesktop.org/mailman/listinfo/intel-gfx

-- 
Daniel Vetter
Software Engineer, Intel Corporation
+41 (0) 79 365 57 48 - http://blog.ffwll.ch