[Intel-gfx] [PATCH] Enable dithering for ns2501 DVO (2)
Daniel Vetter
daniel at ffwll.ch
Thu Apr 16 01:05:17 PDT 2015
On Wed, Apr 15, 2015 at 07:46:56PM +0200, Thomas Richter wrote:
> Hi Daniel, hi Ville,
>
> please find the reworked NS2501 DVO patch with changes as suggested
> attached.
> Unfortunately, the relation between the DVO scaler settings and the actual
> mode
> values remain still somewhat mysterious, so the mode settings remain a table
> lookup
> at this time. On the bright side, the image quality improved notably due to
> dithering.
>
> Greetings,
> Thomas
>
> Signed-off-by: Thomas Richter <thor at math.tu-berlin.de>
>
> This patch enables the (unfortunately undocumented) scaler of the
> NatSemi 2501 DVO found in the Fujitsu-Siemens S6010 laptop and other
> machines of the same series and age.
>
> Parts of the DVO scaler logic have been revealed by reverse
> engineering and trial and error, so your milage may vary. The
> patch (and the whole ns2501 DVO code) is currently only good for
> the 1024x768 panel of the S6010, and may hopefully work on other
> machines with the same panel size.
>
> The mode-specific configuration of the scaler have been moved out
> into a separate class, the mode-agnostic settings remain as raw
> register list as their purpose remains unclear at this point.
I have no idea what exact commands you're using, but I can't apply this
without manually editing the entire mail and stitching together the patch
again. Imo really just use git send-email to send around patches and
_dont_ edit anything by hand. git gets this right.
Another nit: The s-o-b line should be at the bottom of the commit message,
see Documentation/SubmittingPatches.
Thanks, Daniel
>
> ---
> --- dvo_ns2501.c 2015-04-15 19:36:31.000000000 +0200
> +++ dvo_ns2501.c-org 2015-04-14 15:34:34.000000000 +0200
> @@ -60,130 +60,6 @@
>
> #define NS2501_REGC 0x0c
>
> -/*
> - * The following registers are not part of the official datasheet
> - * and are the result of reverse engineering.
> - */
> -
> -/*
> - * Register c0 controls how the DVO synchronizes with
> - * its input.
> - */
> -#define NS2501_REGC0 0xc0
> -#define NS2501_C0_ENABLE (1<<0) /* enable the DVO sync in general */
> -#define NS2501_C0_HSYNC (1<<1) /* synchronize horizontal with input */
> -#define NS2501_C0_VSYNC (1<<2) /* synchronize vertical with input */
> -#define NS2501_C0_RESET (1<<7) /* reset the synchronization flip/flops */
> -
> -/*
> - * Register 41 is somehow related to the sync register and sync
> - * configuration. It should be 0x32 whenever regC0 is 0x05 (hsync off)
> - * and 0x00 otherwise.
> - */
> -#define NS2501_REG41 0x41
> -
> -/*
> - * this register controls the dithering of the DVO
> - * One bit enables it, the other define the dithering depth.
> - * The higher the value, the lower the dithering depth.
> - */
> -#define NS2501_F9_REG 0xf9
> -#define NS2501_F9_ENABLE (1<<0) /* if set, dithering is enabled */
> -#define NS2501_F9_DITHER_MASK (0x7f<<1) /* controls the dither depth */
> -#define NS2501_F9_DITHER_SHIFT 1 /* shifts the dither mask */
> -
> -/*
> - * PLL configuration register. This is a pair of registers,
> - * one single byte register at 1B, and a pair at 1C,1D.
> - * These registers are counters/dividers.
> - */
> -#define NS2501_REG1B 0x1b /* one byte PLL control register */
> -#define NS2501_REG1C 0x1c /* low-part of the second register */
> -#define NS2501_REG1D 0x1d /* high-part of the second register */
> -
> -/*
> - * Scaler control registers. Horizontal at b8,b9,
> - * vertical at 10,11. The scale factor is computed as
> - * 2^16/control-value. The low-byte comes first.
> - */
> -#define NS2501_REG10 0x10 /* low-byte vertical scaler */
> -#define NS2501_REG11 0x11 /* high-byte vertical scaler */
> -#define NS2501_REGB8 0xb8 /* low-byte horizontal scaler */
> -#define NS2501_REGB9 0xb9 /* high-byte horizontal scaler */
> -
> -/*
> - * Display window definition. This consists of four registers
> - * per dimension. One register pair defines the start of the
> - * display, one the end.
> - * As far as I understand, this defines the window within which
> - * the scaler samples the input.
> - */
> -#define NS2501_REGC1 0xc1 /* low-byte horizontal display start */
> -#define NS2501_REGC2 0xc2 /* high-byte horizontal display start */
> -#define NS2501_REGC3 0xc3 /* low-byte horizontal display stop */
> -#define NS2501_REGC4 0xc4 /* high-byte horizontal display stop */
> -#define NS2501_REGC5 0xc5 /* low-byte vertical display start */
> -#define NS2501_REGC6 0xc6 /* high-byte vertical display start */
> -#define NS2501_REGC7 0xc7 /* low-byte vertical display stop */
> -#define NS2501_REGC8 0xc8 /* high-byte vertical display stop */
> -
> -/*
> - * The following register pair seems to define the start of
> - * the vertical sync. If automatic syncing is enabled, and the
> - * register value defines a sync pulse that is later than the
> - * incoming sync, then the register value is ignored and the
> - * external hsync triggers the synchronization.
> - */
> -#define NS2501_REG80 0x80 /* low-byte vsync-start */
> -#define NS2501_REG81 0x81 /* high-byte vsync-start */
> -
> -/*
> - * The following register pair seems to define the total number
> - * of lines created at the output side of the scaler.
> - * This is again a low-high register pair.
> - */
> -#define NS2501_REG82 0x82 /* output display height, low byte */
> -#define NS2501_REG83 0x83 /* output display height, high byte */
> -
> -/*
> - * The following registers define the end of the front-porch
> - * in horizontal and vertical position and hence allow to shift
> - * the image left/right or up/down.
> - */
> -#define NS2501_REG98 0x98 /* horizontal start of display + 256, low */
> -#define NS2501_REG99 0x99 /* horizontal start of display + 256, high */
> -#define NS2501_REG8E 0x8e /* vertical start of the display, low byte */
> -#define NS2501_REG8F 0x8f /* vertical start of the display, high byte */
> -
> -/*
> - * The following register pair control the function of the
> - * backlight and the DVO output. To enable the corresponding
> - * function, the corresponding bit must be set in both registers.
> - */
> -#define NS2501_REG34 0x34 /* DVO enable functions, first register */
> -#define NS2501_REG35 0x35 /* DVO enable functions, second register */
> -#define NS2501_34_ENABLE_OUTPUT (1<<0) /* enable DVO output */
> -#define NS2501_34_ENABLE_BACKLIGHT (1<<1) /* enable backlight */
> -
> -/*
> - * Registers 9C and 9D define the vertical output offset
> - * of the visible region.
> - */
> -#define NS2501_REG9C 0x9c
> -#define NS2501_REG9D 0x9d
> -
> -/*
> - * The register 9F defines the dithering. This requires the
> - * scaler to be ON. Bit 0 enables dithering, the remaining
> - * bits control the depth of the dither. The higher the value,
> - * the LOWER the dithering amplitude. A good value seems to be
> - * 15 (total register value).
> - */
> -#define NS2501_REGF9 0xf9
> -#define NS2501_F9_ENABLE_DITHER (1<<0) /* enable dithering */
> -#define NS2501_F9_DITHER_MASK (0x7f<<1) /* dither masking */
> -#define NS2501_F9_DITHER_SHIFT 1 /* upshift of the dither mask */
> -
> enum {
> MODE_640x480,
> MODE_800x600,
> @@ -196,178 +72,274 @@
> };
>
> /*
> - * The following structure keeps the complete configuration of
> - * the DVO, given a specific output configuration.
> - * This is pretty much guess-work from reverse-engineering, so
> - * read all this with a grain of salt.
> - */
> -struct ns2501_configuration {
> - uint8_t sync; /* configuration of the C0 register */
> - uint8_t conf; /* configuration register 8 */
> - uint8_t syncb; /* configuration register 41 */
> - uint8_t dither; /* configuration of the dithering */
> - uint8_t pll_a; /* PLL configuration, register A, 1B */
> - uint16_t pll_b; /* PLL configuration, register B, 1C/1D */
> - uint16_t hstart; /* horizontal start, registers C1/C2 */
> - uint16_t hstop; /* horizontal total, registers C3/C4 */
> - uint16_t vstart; /* vertical start, registers C5/C6 */
> - uint16_t vstop; /* vertical total, registers C7/C8 */
> - uint16_t vsync; /* manual vertical sync start, 80/81 */
> - uint16_t vtotal; /* number of lines generated, 82/83 */
> - uint16_t hpos; /* horizontal position + 256, 98/99 */
> - uint16_t vpos; /* vertical position, 8e/8f */
> - uint16_t voffs; /* vertical output offset, 9c/9d */
> - uint16_t hscale; /* horizontal scaling factor, b8/b9 */
> - uint16_t vscale; /* vertical scaling factor, 10/11 */
> -};
> -
> -/*
> - * DVO configuration values, partially based on what the BIOS
> - * of the Fujitsu Lifebook S6010 writes into registers,
> - * partially found by manual tweaking. These configurations assume
> - * a 1024x768 panel.
> + * Magic values based on what the BIOS on
> + * Fujitsu-Siemens Lifebook S6010 programs (1024x768 panel).
> */
> -static const struct ns2501_configuration ns2501_modes[] = {
> +static const struct ns2501_reg regs_1024x768[][86] = {
> [MODE_640x480] = {
> - .sync = NS2501_C0_ENABLE | NS2501_C0_VSYNC,
> - .conf = NS2501_8_VEN | NS2501_8_HEN | NS2501_8_PD,
> - .syncb = 0x32,
> - .dither = 0x0f,
> - .pll_a = 17,
> - .pll_b = 852,
> - .hstart = 144,
> - .hstop = 783,
> - .vstart = 22,
> - .vstop = 514,
> - .vsync = 2047, /* actually, ignored with this config */
> - .vtotal = 1341,
> - .hpos = 0,
> - .vpos = 16,
> - .voffs = 36,
> - .hscale = 40960,
> - .vscale = 40960
> + [0] = { .offset = 0x0a, .value = 0x81, },
> + [1] = { .offset = 0x18, .value = 0x07, },
> + [2] = { .offset = 0x19, .value = 0x00, },
> + [3] = { .offset = 0x1a, .value = 0x00, },
> + [4] = { .offset = 0x1b, .value = 0x11, },
> + [5] = { .offset = 0x1c, .value = 0x54, },
> + [6] = { .offset = 0x1d, .value = 0x03, },
> + [7] = { .offset = 0x1e, .value = 0x02, },
> + [8] = { .offset = 0xf3, .value = 0x90, },
> + [9] = { .offset = 0xf9, .value = 0x00, },
> + [10] = { .offset = 0xc1, .value = 0x90, },
> + [11] = { .offset = 0xc2, .value = 0x00, },
> + [12] = { .offset = 0xc3, .value = 0x0f, },
> + [13] = { .offset = 0xc4, .value = 0x03, },
> + [14] = { .offset = 0xc5, .value = 0x16, },
> + [15] = { .offset = 0xc6, .value = 0x00, },
> + [16] = { .offset = 0xc7, .value = 0x02, },
> + [17] = { .offset = 0xc8, .value = 0x02, },
> + [18] = { .offset = 0xf4, .value = 0x00, },
> + [19] = { .offset = 0x80, .value = 0xff, },
> + [20] = { .offset = 0x81, .value = 0x07, },
> + [21] = { .offset = 0x82, .value = 0x3d, },
> + [22] = { .offset = 0x83, .value = 0x05, },
> + [23] = { .offset = 0x94, .value = 0x00, },
> + [24] = { .offset = 0x95, .value = 0x00, },
> + [25] = { .offset = 0x96, .value = 0x05, },
> + [26] = { .offset = 0x97, .value = 0x00, },
> + [27] = { .offset = 0x9a, .value = 0x88, },
> + [28] = { .offset = 0x9b, .value = 0x00, },
> + [29] = { .offset = 0x98, .value = 0x00, },
> + [30] = { .offset = 0x99, .value = 0x00, },
> + [31] = { .offset = 0xf7, .value = 0x88, },
> + [32] = { .offset = 0xf8, .value = 0x0a, },
> + [33] = { .offset = 0x9c, .value = 0x24, },
> + [34] = { .offset = 0x9d, .value = 0x00, },
> + [35] = { .offset = 0x9e, .value = 0x25, },
> + [36] = { .offset = 0x9f, .value = 0x03, },
> + [37] = { .offset = 0xa0, .value = 0x28, },
> + [38] = { .offset = 0xa1, .value = 0x01, },
> + [39] = { .offset = 0xa2, .value = 0x28, },
> + [40] = { .offset = 0xa3, .value = 0x05, },
> + [41] = { .offset = 0xb6, .value = 0x09, },
> + [42] = { .offset = 0xb8, .value = 0x00, },
> + [43] = { .offset = 0xb9, .value = 0xa0, },
> + [44] = { .offset = 0xba, .value = 0x00, },
> + [45] = { .offset = 0xbb, .value = 0x20, },
> + [46] = { .offset = 0x10, .value = 0x00, },
> + [47] = { .offset = 0x11, .value = 0xa0, },
> + [48] = { .offset = 0x12, .value = 0x02, },
> + [49] = { .offset = 0x20, .value = 0x00, },
> + [50] = { .offset = 0x22, .value = 0x00, },
> + [51] = { .offset = 0x23, .value = 0x00, },
> + [52] = { .offset = 0x24, .value = 0x00, },
> + [53] = { .offset = 0x25, .value = 0x00, },
> + [54] = { .offset = 0x8c, .value = 0x10, },
> + [55] = { .offset = 0x8d, .value = 0x02, },
> + [56] = { .offset = 0x8e, .value = 0x10, },
> + [57] = { .offset = 0x8f, .value = 0x00, },
> + [58] = { .offset = 0x90, .value = 0xff, },
> + [59] = { .offset = 0x91, .value = 0x07, },
> + [60] = { .offset = 0x92, .value = 0xa0, },
> + [61] = { .offset = 0x93, .value = 0x02, },
> + [62] = { .offset = 0xa5, .value = 0x00, },
> + [63] = { .offset = 0xa6, .value = 0x00, },
> + [64] = { .offset = 0xa7, .value = 0x00, },
> + [65] = { .offset = 0xa8, .value = 0x00, },
> + [66] = { .offset = 0xa9, .value = 0x04, },
> + [67] = { .offset = 0xaa, .value = 0x70, },
> + [68] = { .offset = 0xab, .value = 0x4f, },
> + [69] = { .offset = 0xac, .value = 0x00, },
> + [70] = { .offset = 0xa4, .value = 0x84, },
> + [71] = { .offset = 0x7e, .value = 0x18, },
> + [72] = { .offset = 0x84, .value = 0x00, },
> + [73] = { .offset = 0x85, .value = 0x00, },
> + [74] = { .offset = 0x86, .value = 0x00, },
> + [75] = { .offset = 0x87, .value = 0x00, },
> + [76] = { .offset = 0x88, .value = 0x00, },
> + [77] = { .offset = 0x89, .value = 0x00, },
> + [78] = { .offset = 0x8a, .value = 0x00, },
> + [79] = { .offset = 0x8b, .value = 0x00, },
> + [80] = { .offset = 0x26, .value = 0x00, },
> + [81] = { .offset = 0x27, .value = 0x00, },
> + [82] = { .offset = 0xad, .value = 0x00, },
> + [83] = { .offset = 0x08, .value = 0x30, }, /* 0x31 */
> + [84] = { .offset = 0x41, .value = 0x00, },
> + [85] = { .offset = 0xc0, .value = 0x05, },
> },
> [MODE_800x600] = {
> - .sync = NS2501_C0_ENABLE |
> - NS2501_C0_HSYNC | NS2501_C0_VSYNC,
> - .conf = NS2501_8_VEN | NS2501_8_HEN | NS2501_8_PD,
> - .syncb = 0x00,
> - .dither = 0x0f,
> - .pll_a = 25,
> - .pll_b = 612,
> - .hstart = 215,
> - .hstop = 1016,
> - .vstart = 26,
> - .vstop = 627,
> - .vsync = 807,
> - .vtotal = 1341,
> - .hpos = 0,
> - .vpos = 4,
> - .voffs = 35,
> - .hscale = 51248,
> - .vscale = 51232
> + [0] = { .offset = 0x0a, .value = 0x81, },
> + [1] = { .offset = 0x18, .value = 0x07, },
> + [2] = { .offset = 0x19, .value = 0x00, },
> + [3] = { .offset = 0x1a, .value = 0x00, },
> + [4] = { .offset = 0x1b, .value = 0x19, },
> + [5] = { .offset = 0x1c, .value = 0x64, },
> + [6] = { .offset = 0x1d, .value = 0x02, },
> + [7] = { .offset = 0x1e, .value = 0x02, },
> + [8] = { .offset = 0xf3, .value = 0x90, },
> + [9] = { .offset = 0xf9, .value = 0x00, },
> + [10] = { .offset = 0xc1, .value = 0xd7, },
> + [11] = { .offset = 0xc2, .value = 0x00, },
> + [12] = { .offset = 0xc3, .value = 0xf8, },
> + [13] = { .offset = 0xc4, .value = 0x03, },
> + [14] = { .offset = 0xc5, .value = 0x1a, },
> + [15] = { .offset = 0xc6, .value = 0x00, },
> + [16] = { .offset = 0xc7, .value = 0x73, },
> + [17] = { .offset = 0xc8, .value = 0x02, },
> + [18] = { .offset = 0xf4, .value = 0x00, },
> + [19] = { .offset = 0x80, .value = 0x27, },
> + [20] = { .offset = 0x81, .value = 0x03, },
> + [21] = { .offset = 0x82, .value = 0x41, },
> + [22] = { .offset = 0x83, .value = 0x05, },
> + [23] = { .offset = 0x94, .value = 0x00, },
> + [24] = { .offset = 0x95, .value = 0x00, },
> + [25] = { .offset = 0x96, .value = 0x05, },
> + [26] = { .offset = 0x97, .value = 0x00, },
> + [27] = { .offset = 0x9a, .value = 0x88, },
> + [28] = { .offset = 0x9b, .value = 0x00, },
> + [29] = { .offset = 0x98, .value = 0x00, },
> + [30] = { .offset = 0x99, .value = 0x00, },
> + [31] = { .offset = 0xf7, .value = 0x88, },
> + [32] = { .offset = 0xf8, .value = 0x06, },
> + [33] = { .offset = 0x9c, .value = 0x23, },
> + [34] = { .offset = 0x9d, .value = 0x00, },
> + [35] = { .offset = 0x9e, .value = 0x25, },
> + [36] = { .offset = 0x9f, .value = 0x03, },
> + [37] = { .offset = 0xa0, .value = 0x28, },
> + [38] = { .offset = 0xa1, .value = 0x01, },
> + [39] = { .offset = 0xa2, .value = 0x28, },
> + [40] = { .offset = 0xa3, .value = 0x05, },
> + [41] = { .offset = 0xb6, .value = 0x09, },
> + [42] = { .offset = 0xb8, .value = 0x30, },
> + [43] = { .offset = 0xb9, .value = 0xc8, },
> + [44] = { .offset = 0xba, .value = 0x00, },
> + [45] = { .offset = 0xbb, .value = 0x20, },
> + [46] = { .offset = 0x10, .value = 0x20, },
> + [47] = { .offset = 0x11, .value = 0xc8, },
> + [48] = { .offset = 0x12, .value = 0x02, },
> + [49] = { .offset = 0x20, .value = 0x00, },
> + [50] = { .offset = 0x22, .value = 0x00, },
> + [51] = { .offset = 0x23, .value = 0x00, },
> + [52] = { .offset = 0x24, .value = 0x00, },
> + [53] = { .offset = 0x25, .value = 0x00, },
> + [54] = { .offset = 0x8c, .value = 0x10, },
> + [55] = { .offset = 0x8d, .value = 0x02, },
> + [56] = { .offset = 0x8e, .value = 0x04, },
> + [57] = { .offset = 0x8f, .value = 0x00, },
> + [58] = { .offset = 0x90, .value = 0xff, },
> + [59] = { .offset = 0x91, .value = 0x07, },
> + [60] = { .offset = 0x92, .value = 0xa0, },
> + [61] = { .offset = 0x93, .value = 0x02, },
> + [62] = { .offset = 0xa5, .value = 0x00, },
> + [63] = { .offset = 0xa6, .value = 0x00, },
> + [64] = { .offset = 0xa7, .value = 0x00, },
> + [65] = { .offset = 0xa8, .value = 0x00, },
> + [66] = { .offset = 0xa9, .value = 0x83, },
> + [67] = { .offset = 0xaa, .value = 0x40, },
> + [68] = { .offset = 0xab, .value = 0x32, },
> + [69] = { .offset = 0xac, .value = 0x00, },
> + [70] = { .offset = 0xa4, .value = 0x80, },
> + [71] = { .offset = 0x7e, .value = 0x18, },
> + [72] = { .offset = 0x84, .value = 0x00, },
> + [73] = { .offset = 0x85, .value = 0x00, },
> + [74] = { .offset = 0x86, .value = 0x00, },
> + [75] = { .offset = 0x87, .value = 0x00, },
> + [76] = { .offset = 0x88, .value = 0x00, },
> + [77] = { .offset = 0x89, .value = 0x00, },
> + [78] = { .offset = 0x8a, .value = 0x00, },
> + [79] = { .offset = 0x8b, .value = 0x00, },
> + [80] = { .offset = 0x26, .value = 0x00, },
> + [81] = { .offset = 0x27, .value = 0x00, },
> + [82] = { .offset = 0xad, .value = 0x00, },
> + [83] = { .offset = 0x08, .value = 0x30, }, /* 0x31 */
> + [84] = { .offset = 0x41, .value = 0x00, },
> + [85] = { .offset = 0xc0, .value = 0x07, },
> },
> [MODE_1024x768] = {
> - .sync = NS2501_C0_ENABLE | NS2501_C0_VSYNC,
> - .conf = NS2501_8_VEN | NS2501_8_HEN | NS2501_8_PD,
> - .syncb = 0x32,
> - .dither = 0x0f,
> - .pll_a = 11,
> - .pll_b = 1350,
> - .hstart = 276,
> - .hstop = 1299,
> - .vstart = 15,
> - .vstop = 1056,
> - .vsync = 2047,
> - .vtotal = 1341,
> - .hpos = 0,
> - .vpos = 7,
> - .voffs = 27,
> - .hscale = 65535,
> - .vscale = 65535
> - }
> -};
> -
> -/*
> - * Other configuration values left by the BIOS of the
> - * Fujitsu S6010 in the DVO control registers. Their
> - * value does not depend on the BIOS and their meaning
> - * is unknown.
> - */
> -
> -static const struct ns2501_reg mode_agnostic_values[] = {
> - /* 08 is mode specific */
> - [0] = { .offset = 0x0a, .value = 0x81, },
> - /* 10,11 are part of the mode specific configuration */
> - [1] = { .offset = 0x12, .value = 0x02, },
> - [2] = { .offset = 0x18, .value = 0x07, },
> - [3] = { .offset = 0x19, .value = 0x00, },
> - [4] = { .offset = 0x1a, .value = 0x00, }, /* PLL?, ignored */
> - /* 1b,1c,1d are part of the mode specific configuration */
> - [5] = { .offset = 0x1e, .value = 0x02, },
> - [6] = { .offset = 0x1f, .value = 0x40, },
> - [7] = { .offset = 0x20, .value = 0x00, },
> - [8] = { .offset = 0x21, .value = 0x00, },
> - [9] = { .offset = 0x22, .value = 0x00, },
> - [10] = { .offset = 0x23, .value = 0x00, },
> - [11] = { .offset = 0x24, .value = 0x00, },
> - [12] = { .offset = 0x25, .value = 0x00, },
> - [13] = { .offset = 0x26, .value = 0x00, },
> - [14] = { .offset = 0x27, .value = 0x00, },
> - [15] = { .offset = 0x7e, .value = 0x18, },
> - /* 80-84 are part of the mode-specific configuration */
> - [16] = { .offset = 0x84, .value = 0x00, },
> - [17] = { .offset = 0x85, .value = 0x00, },
> - [18] = { .offset = 0x86, .value = 0x00, },
> - [19] = { .offset = 0x87, .value = 0x00, },
> - [20] = { .offset = 0x88, .value = 0x00, },
> - [21] = { .offset = 0x89, .value = 0x00, },
> - [22] = { .offset = 0x8a, .value = 0x00, },
> - [23] = { .offset = 0x8b, .value = 0x00, },
> - [24] = { .offset = 0x8c, .value = 0x10, },
> - [25] = { .offset = 0x8d, .value = 0x02, },
> - /* 8e,8f are part of the mode-specific configuration */
> - [26] = { .offset = 0x90, .value = 0xff, },
> - [27] = { .offset = 0x91, .value = 0x07, },
> - [28] = { .offset = 0x92, .value = 0xa0, },
> - [29] = { .offset = 0x93, .value = 0x02, },
> - [30] = { .offset = 0x94, .value = 0x00, },
> - [31] = { .offset = 0x95, .value = 0x00, },
> - [32] = { .offset = 0x96, .value = 0x05, },
> - [33] = { .offset = 0x97, .value = 0x00, },
> - /* 98,99 are part of the mode-specific configuration */
> - [34] = { .offset = 0x9a, .value = 0x88, },
> - [35] = { .offset = 0x9b, .value = 0x00, },
> - /* 9c,9d are part of the mode-specific configuration */
> - [36] = { .offset = 0x9e, .value = 0x25, },
> - [37] = { .offset = 0x9f, .value = 0x03, },
> - [38] = { .offset = 0xa0, .value = 0x28, },
> - [39] = { .offset = 0xa1, .value = 0x01, },
> - [40] = { .offset = 0xa2, .value = 0x28, },
> - [41] = { .offset = 0xa3, .value = 0x05, },
> - /* register 0xa4 is mode specific, but 0x80..0x84 works always */
> - [42] = { .offset = 0xa4, .value = 0x84, },
> - [43] = { .offset = 0xa5, .value = 0x00, },
> - [44] = { .offset = 0xa6, .value = 0x00, },
> - [45] = { .offset = 0xa7, .value = 0x00, },
> - [46] = { .offset = 0xa8, .value = 0x00, },
> - /* 0xa9 to 0xab are mode specific, but have no visible effect */
> - [47] = { .offset = 0xa9, .value = 0x04, },
> - [48] = { .offset = 0xaa, .value = 0x70, },
> - [49] = { .offset = 0xab, .value = 0x4f, },
> - [50] = { .offset = 0xac, .value = 0x00, },
> - [51] = { .offset = 0xad, .value = 0x00, },
> - [52] = { .offset = 0xb6, .value = 0x09, },
> - [53] = { .offset = 0xb7, .value = 0x03, },
> - /* b8,b9 are part of the mode-specific configuration */
> - [54] = { .offset = 0xba, .value = 0x00, },
> - [55] = { .offset = 0xbb, .value = 0x20, },
> - [56] = { .offset = 0xf3, .value = 0x90, },
> - [57] = { .offset = 0xf4, .value = 0x00, },
> - [58] = { .offset = 0xf7, .value = 0x88, },
> - /* f8 is mode specific, but the value does not matter */
> - [59] = { .offset = 0xf8, .value = 0x0a, },
> - [60] = { .offset = 0xf9, .value = 0x00, }
> + [0] = { .offset = 0x0a, .value = 0x81, },
> + [1] = { .offset = 0x18, .value = 0x07, },
> + [2] = { .offset = 0x19, .value = 0x00, },
> + [3] = { .offset = 0x1a, .value = 0x00, },
> + [4] = { .offset = 0x1b, .value = 0x11, },
> + [5] = { .offset = 0x1c, .value = 0x54, },
> + [6] = { .offset = 0x1d, .value = 0x03, },
> + [7] = { .offset = 0x1e, .value = 0x02, },
> + [8] = { .offset = 0xf3, .value = 0x90, },
> + [9] = { .offset = 0xf9, .value = 0x00, },
> + [10] = { .offset = 0xc1, .value = 0x90, },
> + [11] = { .offset = 0xc2, .value = 0x00, },
> + [12] = { .offset = 0xc3, .value = 0x0f, },
> + [13] = { .offset = 0xc4, .value = 0x03, },
> + [14] = { .offset = 0xc5, .value = 0x16, },
> + [15] = { .offset = 0xc6, .value = 0x00, },
> + [16] = { .offset = 0xc7, .value = 0x02, },
> + [17] = { .offset = 0xc8, .value = 0x02, },
> + [18] = { .offset = 0xf4, .value = 0x00, },
> + [19] = { .offset = 0x80, .value = 0xff, },
> + [20] = { .offset = 0x81, .value = 0x07, },
> + [21] = { .offset = 0x82, .value = 0x3d, },
> + [22] = { .offset = 0x83, .value = 0x05, },
> + [23] = { .offset = 0x94, .value = 0x00, },
> + [24] = { .offset = 0x95, .value = 0x00, },
> + [25] = { .offset = 0x96, .value = 0x05, },
> + [26] = { .offset = 0x97, .value = 0x00, },
> + [27] = { .offset = 0x9a, .value = 0x88, },
> + [28] = { .offset = 0x9b, .value = 0x00, },
> + [29] = { .offset = 0x98, .value = 0x00, },
> + [30] = { .offset = 0x99, .value = 0x00, },
> + [31] = { .offset = 0xf7, .value = 0x88, },
> + [32] = { .offset = 0xf8, .value = 0x0a, },
> + [33] = { .offset = 0x9c, .value = 0x24, },
> + [34] = { .offset = 0x9d, .value = 0x00, },
> + [35] = { .offset = 0x9e, .value = 0x25, },
> + [36] = { .offset = 0x9f, .value = 0x03, },
> + [37] = { .offset = 0xa0, .value = 0x28, },
> + [38] = { .offset = 0xa1, .value = 0x01, },
> + [39] = { .offset = 0xa2, .value = 0x28, },
> + [40] = { .offset = 0xa3, .value = 0x05, },
> + [41] = { .offset = 0xb6, .value = 0x09, },
> + [42] = { .offset = 0xb8, .value = 0x00, },
> + [43] = { .offset = 0xb9, .value = 0xa0, },
> + [44] = { .offset = 0xba, .value = 0x00, },
> + [45] = { .offset = 0xbb, .value = 0x20, },
> + [46] = { .offset = 0x10, .value = 0x00, },
> + [47] = { .offset = 0x11, .value = 0xa0, },
> + [48] = { .offset = 0x12, .value = 0x02, },
> + [49] = { .offset = 0x20, .value = 0x00, },
> + [50] = { .offset = 0x22, .value = 0x00, },
> + [51] = { .offset = 0x23, .value = 0x00, },
> + [52] = { .offset = 0x24, .value = 0x00, },
> + [53] = { .offset = 0x25, .value = 0x00, },
> + [54] = { .offset = 0x8c, .value = 0x10, },
> + [55] = { .offset = 0x8d, .value = 0x02, },
> + [56] = { .offset = 0x8e, .value = 0x10, },
> + [57] = { .offset = 0x8f, .value = 0x00, },
> + [58] = { .offset = 0x90, .value = 0xff, },
> + [59] = { .offset = 0x91, .value = 0x07, },
> + [60] = { .offset = 0x92, .value = 0xa0, },
> + [61] = { .offset = 0x93, .value = 0x02, },
> + [62] = { .offset = 0xa5, .value = 0x00, },
> + [63] = { .offset = 0xa6, .value = 0x00, },
> + [64] = { .offset = 0xa7, .value = 0x00, },
> + [65] = { .offset = 0xa8, .value = 0x00, },
> + [66] = { .offset = 0xa9, .value = 0x04, },
> + [67] = { .offset = 0xaa, .value = 0x70, },
> + [68] = { .offset = 0xab, .value = 0x4f, },
> + [69] = { .offset = 0xac, .value = 0x00, },
> + [70] = { .offset = 0xa4, .value = 0x84, },
> + [71] = { .offset = 0x7e, .value = 0x18, },
> + [72] = { .offset = 0x84, .value = 0x00, },
> + [73] = { .offset = 0x85, .value = 0x00, },
> + [74] = { .offset = 0x86, .value = 0x00, },
> + [75] = { .offset = 0x87, .value = 0x00, },
> + [76] = { .offset = 0x88, .value = 0x00, },
> + [77] = { .offset = 0x89, .value = 0x00, },
> + [78] = { .offset = 0x8a, .value = 0x00, },
> + [79] = { .offset = 0x8b, .value = 0x00, },
> + [80] = { .offset = 0x26, .value = 0x00, },
> + [81] = { .offset = 0x27, .value = 0x00, },
> + [82] = { .offset = 0xad, .value = 0x00, },
> + [83] = { .offset = 0x08, .value = 0x34, }, /* 0x35 */
> + [84] = { .offset = 0x41, .value = 0x00, },
> + [85] = { .offset = 0xc0, .value = 0x01, },
> + },
> };
>
> static const struct ns2501_reg regs_init[] = {
> @@ -378,12 +350,25 @@
>
> struct ns2501_priv {
> bool quiet;
> - const struct ns2501_configuration *conf;
> + const struct ns2501_reg *regs;
> };
>
> #define NSPTR(d) ((NS2501Ptr)(d->DriverPrivate.ptr))
>
> /*
> + * For reasons unclear to me, the ns2501 at least on the Fujitsu/Siemens
> + * laptops does not react on the i2c bus unless
> + * both the PLL is running and the display is configured in its native
> + * resolution.
> + * This function forces the DVO on, and stores the registers it touches.
> + * Afterwards, registers are restored to regular values.
> + *
> + * This is pretty much a hack, though it works.
> + * Without that, ns2501_readb and ns2501_writeb fail
> + * when switching the resolution.
> + */
> +
> +/*
> ** Read a register from the ns2501.
> ** Returns true if successful, false otherwise.
> ** If it returns false, it might be wise to enable the
> @@ -549,7 +534,6 @@
> struct drm_display_mode *mode,
> struct drm_display_mode *adjusted_mode)
> {
> - const struct ns2501_configuration *conf;
> struct ns2501_priv *ns = (struct ns2501_priv *)(dvo->dev_priv);
> int mode_idx, i;
>
> @@ -557,36 +541,6 @@
> ("set mode (hdisplay=%d,htotal=%d,vdisplay=%d,vtotal=%d).\n",
> mode->hdisplay, mode->htotal, mode->vdisplay, mode->vtotal);
>
> - DRM_DEBUG_KMS("Detailed requested mode settings are:\n"
> - "clock : %d kHz\n"
> - "hdisplay : %d\n"
> - "hblank start : %d\n"
> - "hblank end : %d\n"
> - "hsync start : %d\n"
> - "hsync end : %d\n"
> - "htotal : %d\n"
> - "hskew : %d\n"
> - "vdisplay : %d\n"
> - "vblank start : %d\n"
> - "hblank end : %d\n"
> - "vsync start : %d\n"
> - "vsync end : %d\n"
> - "vtotal : %d\n",
> - adjusted_mode->crtc_clock,
> - adjusted_mode->crtc_hdisplay,
> - adjusted_mode->crtc_hblank_start,
> - adjusted_mode->crtc_hblank_end,
> - adjusted_mode->crtc_hsync_start,
> - adjusted_mode->crtc_hsync_end,
> - adjusted_mode->crtc_htotal,
> - adjusted_mode->crtc_hskew,
> - adjusted_mode->crtc_vdisplay,
> - adjusted_mode->crtc_vblank_start,
> - adjusted_mode->crtc_vblank_end,
> - adjusted_mode->crtc_vsync_start,
> - adjusted_mode->crtc_vsync_end,
> - adjusted_mode->crtc_vtotal);
> -
> if (mode->hdisplay == 640 && mode->vdisplay == 480)
> mode_idx = MODE_640x480;
> else if (mode->hdisplay == 800 && mode->vdisplay == 600)
> @@ -600,44 +554,10 @@
> for (i = 0; i < ARRAY_SIZE(regs_init); i++)
> ns2501_writeb(dvo, regs_init[i].offset, regs_init[i].value);
>
> - /* Write the mode-agnostic values */
> - for (i = 0; i < ARRAY_SIZE(mode_agnostic_values); i++)
> - ns2501_writeb(dvo, mode_agnostic_values[i].offset,
> - mode_agnostic_values[i].value);
> -
> - /* Write now the mode-specific configuration */
> - conf = ns2501_modes + mode_idx;
> - ns->conf = conf;
> -
> - ns2501_writeb(dvo, NS2501_REG8, conf->conf);
> - ns2501_writeb(dvo, NS2501_REG1B, conf->pll_a);
> - ns2501_writeb(dvo, NS2501_REG1C, conf->pll_b & 0xff);
> - ns2501_writeb(dvo, NS2501_REG1D, conf->pll_b >> 8);
> - ns2501_writeb(dvo, NS2501_REGC1, conf->hstart & 0xff);
> - ns2501_writeb(dvo, NS2501_REGC2, conf->hstart >> 8);
> - ns2501_writeb(dvo, NS2501_REGC3, conf->hstop & 0xff);
> - ns2501_writeb(dvo, NS2501_REGC4, conf->hstop >> 8);
> - ns2501_writeb(dvo, NS2501_REGC5, conf->vstart & 0xff);
> - ns2501_writeb(dvo, NS2501_REGC6, conf->vstart >> 8);
> - ns2501_writeb(dvo, NS2501_REGC7, conf->vstop & 0xff);
> - ns2501_writeb(dvo, NS2501_REGC8, conf->vstop >> 8);
> - ns2501_writeb(dvo, NS2501_REG80, conf->vsync & 0xff);
> - ns2501_writeb(dvo, NS2501_REG81, conf->vsync >> 8);
> - ns2501_writeb(dvo, NS2501_REG82, conf->vtotal & 0xff);
> - ns2501_writeb(dvo, NS2501_REG83, conf->vtotal >> 8);
> - ns2501_writeb(dvo, NS2501_REG98, conf->hpos & 0xff);
> - ns2501_writeb(dvo, NS2501_REG99, conf->hpos >> 8);
> - ns2501_writeb(dvo, NS2501_REG8E, conf->vpos & 0xff);
> - ns2501_writeb(dvo, NS2501_REG8F, conf->vpos >> 8);
> - ns2501_writeb(dvo, NS2501_REG9C, conf->voffs & 0xff);
> - ns2501_writeb(dvo, NS2501_REG9D, conf->voffs >> 8);
> - ns2501_writeb(dvo, NS2501_REGB8, conf->hscale & 0xff);
> - ns2501_writeb(dvo, NS2501_REGB9, conf->hscale >> 8);
> - ns2501_writeb(dvo, NS2501_REG10, conf->vscale & 0xff);
> - ns2501_writeb(dvo, NS2501_REG11, conf->vscale >> 8);
> - ns2501_writeb(dvo, NS2501_REGF9, conf->dither);
> - ns2501_writeb(dvo, NS2501_REG41, conf->syncb);
> - ns2501_writeb(dvo, NS2501_REGC0, conf->sync);
> + ns->regs = regs_1024x768[mode_idx];
> +
> + for (i = 0; i < 84; i++)
> + ns2501_writeb(dvo, ns->regs[i].offset, ns->regs[i].value);
> }
>
> /* set the NS2501 power state */
> @@ -659,32 +579,34 @@
> DRM_DEBUG_KMS("Trying set the dpms of the DVO to %i\n", enable);
>
> if (enable) {
> - ns2501_writeb(dvo, NS2501_REGC0, ns->conf->sync | 0x08);
> + if (WARN_ON(ns->regs[83].offset != 0x08 ||
> + ns->regs[84].offset != 0x41 ||
> + ns->regs[85].offset != 0xc0))
> + return;
> +
> + ns2501_writeb(dvo, 0xc0, ns->regs[85].value | 0x08);
>
> - ns2501_writeb(dvo, NS2501_REG41, ns->conf->syncb);
> + ns2501_writeb(dvo, 0x41, ns->regs[84].value);
>
> - ns2501_writeb(dvo, NS2501_REG34, NS2501_34_ENABLE_OUTPUT);
> + ns2501_writeb(dvo, 0x34, 0x01);
> msleep(15);
>
> - ns2501_writeb(dvo, NS2501_REG8,
> - ns->conf->conf | NS2501_8_BPAS);
> - if (!(ns->conf->conf & NS2501_8_BPAS))
> - ns2501_writeb(dvo, NS2501_REG8, ns->conf->conf);
> + ns2501_writeb(dvo, 0x08, 0x35);
> + if (!(ns->regs[83].value & NS2501_8_BPAS))
> + ns2501_writeb(dvo, 0x08, 0x31);
> msleep(200);
>
> - ns2501_writeb(dvo, NS2501_REG34,
> - NS2501_34_ENABLE_OUTPUT | NS2501_34_ENABLE_BACKLIGHT);
> + ns2501_writeb(dvo, 0x34, 0x03);
>
> - ns2501_writeb(dvo, NS2501_REGC0, ns->conf->sync);
> + ns2501_writeb(dvo, 0xc0, ns->regs[85].value);
> } else {
> - ns2501_writeb(dvo, NS2501_REG34, NS2501_34_ENABLE_OUTPUT);
> + ns2501_writeb(dvo, 0x34, 0x01);
> msleep(200);
>
> - ns2501_writeb(dvo, NS2501_REG8, NS2501_8_VEN | NS2501_8_HEN |
> - NS2501_8_BPAS);
> + ns2501_writeb(dvo, 0x08, 0x34);
> msleep(15);
>
> - ns2501_writeb(dvo, NS2501_REG34, 0x00);
> + ns2501_writeb(dvo, 0x34, 0x00);
> }
> }
>
--
Daniel Vetter
Software Engineer, Intel Corporation
http://blog.ffwll.ch
More information about the Intel-gfx
mailing list