[Intel-gfx] [PATCH v2] drm/i915: Put back lane_count into intel_dp and add link_rate too
ville.syrjala at linux.intel.com
ville.syrjala at linux.intel.com
Mon Aug 17 08:05:12 PDT 2015
From: Ville Syrjälä <ville.syrjala at linux.intel.com>
With MST there won't be a crtc assigned to the main link encoder, so
trying to dig up the pipe_config from there is a recipe for an oops.
Instead store the parameters (lane_count and link_rate) in the encoder,
and use those values during link training etc. Since those parameters
are now assigned only when the link is actually enabled,
.compute_config() won't clobber them as it did before.
Hardware state readout is still bonkers though as we don't transfer the
link parameters from pipe_config intel_dp. We should do that during
encoder sanitation. But since we don't even do a proper job of reading
out the main link encoder state for MST there's littel point in
worrying about this now.
Fixes a regression with MST caused by:
commit 90a6b7b052b1aa17fbb98b049e9c8b7f729c35a7
Author: Ville Syrjälä <ville.syrjala at linux.intel.com>
Date: Mon Jul 6 16:39:15 2015 +0300
drm/i915: Move intel_dp->lane_count into pipe_config
v2: Different apporoach that should keep intel_dp_check_mst_status()
somewhat less oopsy
Cc: Maarten Lankhorst <maarten.lankhorst at linux.intel.com>
Reported-by: Maarten Lankhorst <maarten.lankhorst at linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala at linux.intel.com>
---
drivers/gpu/drm/i915/intel_ddi.c | 5 ++--
drivers/gpu/drm/i915/intel_dp.c | 53 +++++++++++++++++--------------------
drivers/gpu/drm/i915/intel_dp_mst.c | 2 ++
drivers/gpu/drm/i915/intel_drv.h | 4 +++
4 files changed, 33 insertions(+), 31 deletions(-)
diff --git a/drivers/gpu/drm/i915/intel_ddi.c b/drivers/gpu/drm/i915/intel_ddi.c
index 56d778f..5dff8b7 100644
--- a/drivers/gpu/drm/i915/intel_ddi.c
+++ b/drivers/gpu/drm/i915/intel_ddi.c
@@ -728,11 +728,10 @@ void intel_ddi_init_dp_buf_reg(struct intel_encoder *encoder)
struct intel_dp *intel_dp = enc_to_intel_dp(&encoder->base);
struct intel_digital_port *intel_dig_port =
enc_to_dig_port(&encoder->base);
- struct intel_crtc *crtc = to_intel_crtc(encoder->base.crtc);
intel_dp->DP = intel_dig_port->saved_port_bits |
DDI_BUF_CTL_ENABLE | DDI_BUF_TRANS_SELECT(0);
- intel_dp->DP |= DDI_PORT_WIDTH(crtc->config->lane_count);
+ intel_dp->DP |= DDI_PORT_WIDTH(intel_dp->lane_count);
}
static struct intel_encoder *
@@ -2314,6 +2313,8 @@ static void intel_ddi_pre_enable(struct intel_encoder *intel_encoder)
if (type == INTEL_OUTPUT_DISPLAYPORT || type == INTEL_OUTPUT_EDP) {
struct intel_dp *intel_dp = enc_to_intel_dp(encoder);
+ intel_dp_set_link_params(intel_dp, crtc->config);
+
intel_ddi_init_dp_buf_reg(intel_encoder);
intel_dp_sink_dpms(intel_dp, DRM_MODE_DPMS_ON);
diff --git a/drivers/gpu/drm/i915/intel_dp.c b/drivers/gpu/drm/i915/intel_dp.c
index b905c19..dcda86a 100644
--- a/drivers/gpu/drm/i915/intel_dp.c
+++ b/drivers/gpu/drm/i915/intel_dp.c
@@ -1584,6 +1584,13 @@ static void ironlake_set_pll_cpu_edp(struct intel_dp *intel_dp)
udelay(500);
}
+void intel_dp_set_link_params(struct intel_dp *intel_dp,
+ const struct intel_crtc_state *pipe_config)
+{
+ intel_dp->link_rate = pipe_config->port_clock;
+ intel_dp->lane_count = pipe_config->lane_count;
+}
+
static void intel_dp_prepare(struct intel_encoder *encoder)
{
struct drm_device *dev = encoder->base.dev;
@@ -1593,6 +1600,8 @@ static void intel_dp_prepare(struct intel_encoder *encoder)
struct intel_crtc *crtc = to_intel_crtc(encoder->base.crtc);
struct drm_display_mode *adjusted_mode = &crtc->config->base.adjusted_mode;
+ intel_dp_set_link_params(intel_dp, crtc->config);
+
/*
* There are four kinds of DP registers:
*
@@ -3348,15 +3357,13 @@ static void
intel_get_adjust_train(struct intel_dp *intel_dp,
const uint8_t link_status[DP_LINK_STATUS_SIZE])
{
- struct intel_crtc *crtc =
- to_intel_crtc(dp_to_dig_port(intel_dp)->base.base.crtc);
uint8_t v = 0;
uint8_t p = 0;
int lane;
uint8_t voltage_max;
uint8_t preemph_max;
- for (lane = 0; lane < crtc->config->lane_count; lane++) {
+ for (lane = 0; lane < intel_dp->lane_count; lane++) {
uint8_t this_v = drm_dp_get_adjust_request_voltage(link_status, lane);
uint8_t this_p = drm_dp_get_adjust_request_pre_emphasis(link_status, lane);
@@ -3527,8 +3534,6 @@ intel_dp_set_link_train(struct intel_dp *intel_dp,
struct intel_digital_port *intel_dig_port = dp_to_dig_port(intel_dp);
struct drm_i915_private *dev_priv =
to_i915(intel_dig_port->base.base.dev);
- struct intel_crtc *crtc =
- to_intel_crtc(intel_dig_port->base.base.crtc);
uint8_t buf[sizeof(intel_dp->train_set) + 1];
int ret, len;
@@ -3544,8 +3549,8 @@ intel_dp_set_link_train(struct intel_dp *intel_dp,
len = 1;
} else {
/* DP_TRAINING_LANEx_SET follow DP_TRAINING_PATTERN_SET */
- memcpy(buf + 1, intel_dp->train_set, crtc->config->lane_count);
- len = crtc->config->lane_count + 1;
+ memcpy(buf + 1, intel_dp->train_set, intel_dp->lane_count);
+ len = intel_dp->lane_count + 1;
}
ret = drm_dp_dpcd_write(&intel_dp->aux, DP_TRAINING_PATTERN_SET,
@@ -3571,8 +3576,6 @@ intel_dp_update_link_train(struct intel_dp *intel_dp, uint32_t *DP,
struct intel_digital_port *intel_dig_port = dp_to_dig_port(intel_dp);
struct drm_i915_private *dev_priv =
to_i915(intel_dig_port->base.base.dev);
- struct intel_crtc *crtc =
- to_intel_crtc(intel_dig_port->base.base.crtc);
int ret;
intel_get_adjust_train(intel_dp, link_status);
@@ -3582,9 +3585,9 @@ intel_dp_update_link_train(struct intel_dp *intel_dp, uint32_t *DP,
POSTING_READ(intel_dp->output_reg);
ret = drm_dp_dpcd_write(&intel_dp->aux, DP_TRAINING_LANE0_SET,
- intel_dp->train_set, crtc->config->lane_count);
+ intel_dp->train_set, intel_dp->lane_count);
- return ret == crtc->config->lane_count;
+ return ret == intel_dp->lane_count;
}
static void intel_dp_set_idle_link_train(struct intel_dp *intel_dp)
@@ -3623,8 +3626,6 @@ void
intel_dp_start_link_train(struct intel_dp *intel_dp)
{
struct drm_encoder *encoder = &dp_to_dig_port(intel_dp)->base.base;
- struct intel_crtc *crtc =
- to_intel_crtc(dp_to_dig_port(intel_dp)->base.base.crtc);
struct drm_device *dev = encoder->dev;
int i;
uint8_t voltage;
@@ -3636,12 +3637,12 @@ intel_dp_start_link_train(struct intel_dp *intel_dp)
if (HAS_DDI(dev))
intel_ddi_prepare_link_retrain(encoder);
- intel_dp_compute_rate(intel_dp, crtc->config->port_clock,
+ intel_dp_compute_rate(intel_dp, intel_dp->link_rate,
&link_bw, &rate_select);
/* Write the link configuration data */
link_config[0] = link_bw;
- link_config[1] = crtc->config->lane_count;
+ link_config[1] = intel_dp->lane_count;
if (drm_dp_enhanced_frame_cap(intel_dp->dpcd))
link_config[1] |= DP_LANE_COUNT_ENHANCED_FRAME_EN;
drm_dp_dpcd_write(&intel_dp->aux, DP_LINK_BW_SET, link_config, 2);
@@ -3675,7 +3676,7 @@ intel_dp_start_link_train(struct intel_dp *intel_dp)
break;
}
- if (drm_dp_clock_recovery_ok(link_status, crtc->config->lane_count)) {
+ if (drm_dp_clock_recovery_ok(link_status, intel_dp->lane_count)) {
DRM_DEBUG_KMS("clock recovery OK\n");
break;
}
@@ -3698,10 +3699,10 @@ intel_dp_start_link_train(struct intel_dp *intel_dp)
}
/* Check to see if we've tried the max voltage */
- for (i = 0; i < crtc->config->lane_count; i++)
+ for (i = 0; i < intel_dp->lane_count; i++)
if ((intel_dp->train_set[i] & DP_TRAIN_MAX_SWING_REACHED) == 0)
break;
- if (i == crtc->config->lane_count) {
+ if (i == intel_dp->lane_count) {
++loop_tries;
if (loop_tries == 5) {
DRM_ERROR("too many full retries, give up\n");
@@ -3738,15 +3739,13 @@ intel_dp_start_link_train(struct intel_dp *intel_dp)
void
intel_dp_complete_link_train(struct intel_dp *intel_dp)
{
- struct intel_crtc *crtc =
- to_intel_crtc(dp_to_dig_port(intel_dp)->base.base.crtc);
bool channel_eq = false;
int tries, cr_tries;
uint32_t DP = intel_dp->DP;
uint32_t training_pattern = DP_TRAINING_PATTERN_2;
/* Training Pattern 3 for HBR2 or 1.2 devices that support it*/
- if (crtc->config->port_clock == 540000 || intel_dp->use_tps3)
+ if (intel_dp->link_rate == 540000 || intel_dp->use_tps3)
training_pattern = DP_TRAINING_PATTERN_3;
/* channel equalization */
@@ -3776,7 +3775,7 @@ intel_dp_complete_link_train(struct intel_dp *intel_dp)
/* Make sure clock is still ok */
if (!drm_dp_clock_recovery_ok(link_status,
- crtc->config->lane_count)) {
+ intel_dp->lane_count)) {
intel_dp->train_set_valid = false;
intel_dp_start_link_train(intel_dp);
intel_dp_set_link_train(intel_dp, &DP,
@@ -3787,7 +3786,7 @@ intel_dp_complete_link_train(struct intel_dp *intel_dp)
}
if (drm_dp_channel_eq_ok(link_status,
- crtc->config->lane_count)) {
+ intel_dp->lane_count)) {
channel_eq = true;
break;
}
@@ -4285,8 +4284,6 @@ update_status:
static int
intel_dp_check_mst_status(struct intel_dp *intel_dp)
{
- struct intel_crtc *crtc =
- to_intel_crtc(dp_to_dig_port(intel_dp)->base.base.crtc);
bool bret;
if (intel_dp->is_mst) {
@@ -4300,7 +4297,7 @@ go_again:
/* check link status - esi[10] = 0x200c */
if (intel_dp->active_mst_links &&
- !drm_dp_channel_eq_ok(&esi[10], crtc->config->lane_count)) {
+ !drm_dp_channel_eq_ok(&esi[10], intel_dp->lane_count)) {
DRM_DEBUG_KMS("channel EQ not ok, retraining\n");
intel_dp_start_link_train(intel_dp);
intel_dp_complete_link_train(intel_dp);
@@ -4355,8 +4352,6 @@ intel_dp_check_link_status(struct intel_dp *intel_dp)
{
struct drm_device *dev = intel_dp_to_dev(intel_dp);
struct intel_encoder *intel_encoder = &dp_to_dig_port(intel_dp)->base;
- struct intel_crtc *crtc =
- to_intel_crtc(dp_to_dig_port(intel_dp)->base.base.crtc);
u8 sink_irq_vector;
u8 link_status[DP_LINK_STATUS_SIZE];
@@ -4392,7 +4387,7 @@ intel_dp_check_link_status(struct intel_dp *intel_dp)
DRM_DEBUG_DRIVER("CP or sink specific irq unhandled\n");
}
- if (!drm_dp_channel_eq_ok(link_status, crtc->config->lane_count)) {
+ if (!drm_dp_channel_eq_ok(link_status, intel_dp->lane_count)) {
DRM_DEBUG_KMS("%s: channel EQ not ok, retraining\n",
intel_encoder->base.name);
intel_dp_start_link_train(intel_dp);
diff --git a/drivers/gpu/drm/i915/intel_dp_mst.c b/drivers/gpu/drm/i915/intel_dp_mst.c
index 9ec5c20..ebf2054 100644
--- a/drivers/gpu/drm/i915/intel_dp_mst.c
+++ b/drivers/gpu/drm/i915/intel_dp_mst.c
@@ -165,6 +165,8 @@ static void intel_mst_pre_enable_dp(struct intel_encoder *encoder)
if (intel_dp->active_mst_links == 0) {
enum port port = intel_ddi_get_encoder_port(encoder);
+ intel_dp_set_link_params(intel_dp, intel_crtc->config);
+
/* FIXME: add support for SKL */
if (INTEL_INFO(dev)->gen < 9)
I915_WRITE(PORT_CLK_SEL(port),
diff --git a/drivers/gpu/drm/i915/intel_drv.h b/drivers/gpu/drm/i915/intel_drv.h
index 81b7d77..71a2e18 100644
--- a/drivers/gpu/drm/i915/intel_drv.h
+++ b/drivers/gpu/drm/i915/intel_drv.h
@@ -708,6 +708,8 @@ struct intel_dp {
uint32_t output_reg;
uint32_t aux_ch_ctl_reg;
uint32_t DP;
+ int link_rate;
+ uint8_t lane_count;
bool has_audio;
enum hdmi_force_audio force_audio;
bool limited_color_range;
@@ -1161,6 +1163,8 @@ void assert_csr_loaded(struct drm_i915_private *dev_priv);
void intel_dp_init(struct drm_device *dev, int output_reg, enum port port);
bool intel_dp_init_connector(struct intel_digital_port *intel_dig_port,
struct intel_connector *intel_connector);
+void intel_dp_set_link_params(struct intel_dp *intel_dp,
+ const struct intel_crtc_state *pipe_config);
void intel_dp_start_link_train(struct intel_dp *intel_dp);
void intel_dp_complete_link_train(struct intel_dp *intel_dp);
void intel_dp_stop_link_train(struct intel_dp *intel_dp);
--
2.4.6
More information about the Intel-gfx
mailing list