[Intel-gfx] [PATCH v2 07/17] drm/i915: Introduce spt_irq_handler()
Ville Syrjälä
ville.syrjala at linux.intel.com
Fri Aug 28 11:29:16 PDT 2015
On Fri, Aug 28, 2015 at 03:20:33PM -0300, Paulo Zanoni wrote:
> 2015-08-27 17:56 GMT-03:00 <ville.syrjala at linux.intel.com>:
> > From: Ville Syrjälä <ville.syrjala at linux.intel.com>
> >
> > Starting from SPT the only interrupts living in the south are GMBUS and
> > HPD. What's worse some of the SPT specific new bits conflict with some
> > other bits on earlier PCH generations. So better not use the
> > cpt_irq_handler() for SPT+ anymore.
> >
> > Also kill the hand rolled port E handling with something more
> > standardish. This also avoids accidentally confusing port B and port E
> > long pulses since the bits occupy the same positions, just in different
> > registers.
> >
> > Also add a comment noting that the short pulse duration bits are
> > reserved on LPT+. The 2ms value we program is 0, so no issue wrt. the
> > MBZ in the spec.
> >
> > v2: Call intel_hpd_irq_handler() only once (Paulo)
> >
> > Signed-off-by: Ville Syrjälä <ville.syrjala at linux.intel.com>
> > ---
> > drivers/gpu/drm/i915/i915_irq.c | 124 +++++++++++++++++++++++++++-------------
> > 1 file changed, 84 insertions(+), 40 deletions(-)
> >
> > diff --git a/drivers/gpu/drm/i915/i915_irq.c b/drivers/gpu/drm/i915/i915_irq.c
> > index db27945..978a528 100644
> > --- a/drivers/gpu/drm/i915/i915_irq.c
> > +++ b/drivers/gpu/drm/i915/i915_irq.c
> > @@ -1262,6 +1262,16 @@ static bool bxt_port_hotplug_long_detect(enum port port, u32 val)
> > }
> > }
> >
> > +static bool spt_port_hotplug2_long_detect(enum port port, u32 val)
> > +{
> > + switch (port) {
> > + case PORT_E:
> > + return val & PORTE_HOTPLUG_LONG_DETECT;
> > + default:
> > + return false;
> > + }
> > +}
> > +
> > static bool pch_port_hotplug_long_detect(enum port port, u32 val)
> > {
> > switch (port) {
> > @@ -1271,8 +1281,6 @@ static bool pch_port_hotplug_long_detect(enum port port, u32 val)
> > return val & PORTC_HOTPLUG_LONG_DETECT;
> > case PORT_D:
> > return val & PORTD_HOTPLUG_LONG_DETECT;
> > - case PORT_E:
> > - return val & PORTE_HOTPLUG_LONG_DETECT;
> > default:
> > return false;
> > }
> > @@ -1770,12 +1778,7 @@ static void cpt_irq_handler(struct drm_device *dev, u32 pch_iir)
> > {
> > struct drm_i915_private *dev_priv = dev->dev_private;
> > int pipe;
> > - u32 hotplug_trigger;
> > -
> > - if (HAS_PCH_SPT(dev))
> > - hotplug_trigger = pch_iir & SDE_HOTPLUG_MASK_SPT;
> > - else
> > - hotplug_trigger = pch_iir & SDE_HOTPLUG_MASK_CPT;
> > + u32 hotplug_trigger = pch_iir & SDE_HOTPLUG_MASK_CPT;
> >
> > if (hotplug_trigger) {
> > u32 dig_hotplug_reg, pin_mask = 0, long_mask = 0;
> > @@ -1783,22 +1786,10 @@ static void cpt_irq_handler(struct drm_device *dev, u32 pch_iir)
> > dig_hotplug_reg = I915_READ(PCH_PORT_HOTPLUG);
> > I915_WRITE(PCH_PORT_HOTPLUG, dig_hotplug_reg);
> >
> > - if (HAS_PCH_SPT(dev)) {
> > - intel_get_hpd_pins(&pin_mask, &long_mask,
> > - hotplug_trigger,
> > - dig_hotplug_reg, hpd_spt,
> > - pch_port_hotplug_long_detect);
> > -
> > - /* detect PORTE HP event */
> > - dig_hotplug_reg = I915_READ(PCH_PORT_HOTPLUG2);
> > - if (pch_port_hotplug_long_detect(PORT_E,
> > - dig_hotplug_reg))
> > - long_mask |= 1 << HPD_PORT_E;
> > - } else
> > - intel_get_hpd_pins(&pin_mask, &long_mask,
> > - hotplug_trigger,
> > - dig_hotplug_reg, hpd_cpt,
> > - pch_port_hotplug_long_detect);
> > + intel_get_hpd_pins(&pin_mask, &long_mask,
> > + hotplug_trigger,
> > + dig_hotplug_reg, hpd_cpt,
> > + pch_port_hotplug_long_detect);
> >
> > intel_hpd_irq_handler(dev, pin_mask, long_mask);
> > }
> > @@ -1832,6 +1823,43 @@ static void cpt_irq_handler(struct drm_device *dev, u32 pch_iir)
> > cpt_serr_int_handler(dev);
> > }
> >
> > +static void spt_irq_handler(struct drm_device *dev, u32 pch_iir)
> > +{
> > + struct drm_i915_private *dev_priv = dev->dev_private;
> > + u32 hotplug_trigger = pch_iir & SDE_HOTPLUG_MASK_SPT &
> > + ~SDE_PORTE_HOTPLUG_SPT;
> > + u32 hotplug2_trigger = pch_iir & SDE_PORTE_HOTPLUG_SPT;
> > + u32 pin_mask = 0, long_mask = 0;
> > +
> > + if (hotplug_trigger) {
> > + u32 dig_hotplug_reg;
> > +
> > + dig_hotplug_reg = I915_READ(PCH_PORT_HOTPLUG);
> > + I915_WRITE(PCH_PORT_HOTPLUG, dig_hotplug_reg);
> > +
> > + intel_get_hpd_pins(&pin_mask, &long_mask, hotplug_trigger,
> > + dig_hotplug_reg, hpd_spt,
> > + pch_port_hotplug_long_detect);
> > + }
> > +
> > + if (hotplug2_trigger) {
> > + u32 dig_hotplug_reg;
> > +
> > + dig_hotplug_reg = I915_READ(PCH_PORT_HOTPLUG2);
> > + I915_WRITE(PCH_PORT_HOTPLUG2, dig_hotplug_reg);
> > +
> > + intel_get_hpd_pins(&pin_mask, &long_mask, hotplug2_trigger,
> > + dig_hotplug_reg, hpd_spt,
> > + spt_port_hotplug2_long_detect);
> > + }
> > +
> > + if (pin_mask)
> > + intel_hpd_irq_handler(dev, pin_mask, long_mask);
>
> intel_hpd_irq_handler() already checks for empty pin_mask.
I was hoping doing the check here would be cheaper. Otherwise we would
do the function call every time there's a south interrupt, only to
return immediately. Well, gmbus being the only other source of south
interrupts, this might make gmbus handling a bit cheaper...
>
> I'm not sure if my arguments on patch 6 were enough to trigger a v3 of
> this patch, so, in case you stay with the current patch 6, then, with
> or without any of my suggestions:
> Reviewed-by: Paulo Zanoni <paulo.r.zanoni at intel.com>
>
> > +
> > + if (pch_iir & SDE_GMBUS_CPT)
> > + gmbus_irq_handler(dev);
> > +}
> > +
> > static void ilk_display_irq_handler(struct drm_device *dev, u32 de_iir)
> > {
> > struct drm_i915_private *dev_priv = dev->dev_private;
> > @@ -2150,7 +2178,11 @@ static irqreturn_t gen8_irq_handler(int irq, void *arg)
> > if (pch_iir) {
> > I915_WRITE(SDEIIR, pch_iir);
> > ret = IRQ_HANDLED;
> > - cpt_irq_handler(dev, pch_iir);
> > +
> > + if (HAS_PCH_SPT(dev_priv))
> > + spt_irq_handler(dev, pch_iir);
> > + else
> > + cpt_irq_handler(dev, pch_iir);
> > } else
> > DRM_ERROR("The master control interrupt lied (SDE)!\n");
> >
> > @@ -3032,9 +3064,6 @@ static void ibx_hpd_irq_setup(struct drm_device *dev)
> > if (HAS_PCH_IBX(dev)) {
> > hotplug_irqs = SDE_HOTPLUG_MASK;
> > enabled_irqs = intel_hpd_enabled_irqs(dev, hpd_ibx);
> > - } else if (HAS_PCH_SPT(dev)) {
> > - hotplug_irqs = SDE_HOTPLUG_MASK_SPT;
> > - enabled_irqs = intel_hpd_enabled_irqs(dev, hpd_spt);
> > } else {
> > hotplug_irqs = SDE_HOTPLUG_MASK_CPT;
> > enabled_irqs = intel_hpd_enabled_irqs(dev, hpd_cpt);
> > @@ -3044,9 +3073,8 @@ static void ibx_hpd_irq_setup(struct drm_device *dev)
> >
> > /*
> > * Enable digital hotplug on the PCH, and configure the DP short pulse
> > - * duration to 2ms (which is the minimum in the Display Port spec)
> > - *
> > - * This register is the same on all known PCH chips.
> > + * duration to 2ms (which is the minimum in the Display Port spec).
> > + * The pulse duration bits are reserved on LPT+.
> > */
> > hotplug = I915_READ(PCH_PORT_HOTPLUG);
> > hotplug &= ~(PORTD_PULSE_DURATION_MASK|PORTC_PULSE_DURATION_MASK|PORTB_PULSE_DURATION_MASK);
> > @@ -3054,13 +3082,27 @@ static void ibx_hpd_irq_setup(struct drm_device *dev)
> > hotplug |= PORTC_HOTPLUG_ENABLE | PORTC_PULSE_DURATION_2ms;
> > hotplug |= PORTB_HOTPLUG_ENABLE | PORTB_PULSE_DURATION_2ms;
> > I915_WRITE(PCH_PORT_HOTPLUG, hotplug);
> > +}
> >
> > - /* enable SPT PORTE hot plug */
> > - if (HAS_PCH_SPT(dev)) {
> > - hotplug = I915_READ(PCH_PORT_HOTPLUG2);
> > - hotplug |= PORTE_HOTPLUG_ENABLE;
> > - I915_WRITE(PCH_PORT_HOTPLUG2, hotplug);
> > - }
> > +static void spt_hpd_irq_setup(struct drm_device *dev)
> > +{
> > + struct drm_i915_private *dev_priv = dev->dev_private;
> > + u32 hotplug_irqs, hotplug, enabled_irqs;
> > +
> > + hotplug_irqs = SDE_HOTPLUG_MASK_SPT;
> > + enabled_irqs = intel_hpd_enabled_irqs(dev, hpd_spt);
> > +
> > + ibx_display_interrupt_update(dev_priv, hotplug_irqs, enabled_irqs);
> > +
> > + /* Enable digital hotplug on the PCH */
> > + hotplug = I915_READ(PCH_PORT_HOTPLUG);
> > + hotplug |= PORTD_HOTPLUG_ENABLE | PORTC_HOTPLUG_ENABLE |
> > + PORTB_HOTPLUG_ENABLE;
> > + I915_WRITE(PCH_PORT_HOTPLUG, hotplug);
> > +
> > + hotplug = I915_READ(PCH_PORT_HOTPLUG2);
> > + hotplug |= PORTE_HOTPLUG_ENABLE;
> > + I915_WRITE(PCH_PORT_HOTPLUG2, hotplug);
> > }
> >
> > static void bxt_hpd_irq_setup(struct drm_device *dev)
> > @@ -4165,10 +4207,12 @@ void intel_irq_init(struct drm_i915_private *dev_priv)
> > dev->driver->irq_uninstall = gen8_irq_uninstall;
> > dev->driver->enable_vblank = gen8_enable_vblank;
> > dev->driver->disable_vblank = gen8_disable_vblank;
> > - if (HAS_PCH_SPLIT(dev))
> > - dev_priv->display.hpd_irq_setup = ibx_hpd_irq_setup;
> > - else
> > + if (IS_BROXTON(dev))
> > dev_priv->display.hpd_irq_setup = bxt_hpd_irq_setup;
> > + else if (HAS_PCH_SPT(dev))
> > + dev_priv->display.hpd_irq_setup = spt_hpd_irq_setup;
> > + else
> > + dev_priv->display.hpd_irq_setup = ibx_hpd_irq_setup;
> > } else if (HAS_PCH_SPLIT(dev)) {
> > dev->driver->irq_handler = ironlake_irq_handler;
> > dev->driver->irq_preinstall = ironlake_irq_reset;
> > --
> > 2.4.6
> >
> > _______________________________________________
> > Intel-gfx mailing list
> > Intel-gfx at lists.freedesktop.org
> > http://lists.freedesktop.org/mailman/listinfo/intel-gfx
>
>
>
> --
> Paulo Zanoni
--
Ville Syrjälä
Intel OTC
More information about the Intel-gfx
mailing list