[Intel-gfx] [PATCH 3/4] snd: add support for displayport multi-stream to hda codec.

[Liam Girdwood]

On Mon, 2015-06-22 at 15:23 +0200, Takashi Iwai wrote:
> At Mon, 22 Jun 2015 14:54:29 +0200,
> Daniel Vetter wrote:
> > 
> > On Fri, Jun 19, 2015 at 01:15:57PM +0200, Takashi Iwai wrote:
> > > At Fri, 19 Jun 2015 20:33:39 +1000,
> > > Dave Airlie wrote:
> > > > 
> > > > On 19 June 2015 at 19:54, Lin, Mengdong <mengdong.lin at intel.com> wrote:
> > > > > Hi Takashi/Dave,
> > > > >
> > > > > Shall we move or cc this discussion on audio driver side to ALSA ML?
> > > > 
> > > > Oops I thought I had cc'ed these patches to alsa-devel as well when I sent them.
> > > > 
> > > > > I think we also need to decide how to manage PCM devices for DP MST.
> > > > > Now the HD-A driver create a PCM device for each pin, and the substream
> > > > > number is 1 for each PCM. Now with DP MST enabled, each pin can support
> > > > > multiple streams (e.g. 3 on Intel HSW/BDW/SKL).
> > > > >
> > > > > There may be 2 options:
> > > > > -#1: Let an HDMI codec specify number of substreams, same as the number
> > > > > of device entries on a pin. We can specify 3 for HSW/BDW/SKL. Other
> > > > > vendors can also specify a value according to actual HW capabilities.
> > > > >
> > > > > So for HSW, we have 3x3 subtreams totally. But we only have 3 convertors
> > > > > (for 3 display pipelines), so we can open up to 3 substreams at the same
> > > > > time. When the audio driver finds all 3 convertors are used when opening
> > > > > a new substream, it will fail.
> > > > 
> > > > One thing I noticed is the number of devices on a PIN is only updated when
> > > > the MST device is plugged in so normally pins 5,6,7 have 0 devices, and when
> > > > I plug in MST device, I get the 3 devices on port 6. So it seems dynamic
> > > > enough at this point, though I guess it'll always be 0 or 3.
> > > > >
> > > > > - #2: Create PCM device dynamically. Only create a PCM devices for a device
> > > > > entry which connects to monitor with audio support. When the monitor
> > > > > is removed, the PCM device will be disconnected, closed and removed,
> > > > > similar to the USB case.
> > > > >
> > > > > This will change ALSA core. But there will be less PCM devices and
> > > > > substreams, since the number of connected monitors Is decided by the
> > > > > actual GPU display pipeline.
> > > > 
> > > > I like this option more, since I think it should be more like USB, but I've
> > > > no idea how much work it would be from the alsa side, this patch was
> > > > probably as deep into alsa as I've gone.
> > > 
> > > Two things have to be considered for compatibility:
> > > - ELD, channel map and jack detection: these are created per PCM
> > >   device, and extending to substream would confuse user space a lot.
> > >   In theory, it can be extended using subdevice number, but in anyway
> > >   this won't work with PulseAudio as is.
> > > 
> > > - The per-pin assignment provides a more or less persistent route to a
> > >   certain device.  Changing the assignment method may break the
> > >   previous setup.
> > > 
> > > Also, the dynamic PCM creation / removal is an issue that has been
> > > discussed many times.  Unfortunately it won't work as is, at lest for
> > > PA.  Currently PA does probing of devices only at the card probe time.
> > > The hotplug of USB-audio works because it's always tied with the
> > > card.  But in this case, the card remains while only the PCM devices
> > > will be created / removed, thus the probe in PA won't be triggered.
> > 
> > I guess that means we either have to hotplug entire (fake) cards or fix up
> > userspace to support mst audio properly?
> 
> It would work for HSW/BDW.  But BYT/BSW and SKL share the same
> controller for both HDMI and analog codecs, thus the card can't be
> handled as hotplugged.
> 
> > We had to do some minimal changes
> > to the ddx drivers too to make sure they're rescanning the connector list
> > properly. Imo since this is all new I think we could require PA to rescan
> > the PCM dev list on hotplug events too to support DP MST. And we kinda do
> > need hotplug at that level since if we'd hotplug the entire card we'd kill
> > a stream that's running on some other display.
> > 
> > And always registering all of them feels like a very bad hack too.
> 
> Yeah, I personally am for the PCM hotplug, too.  It's a cleaner way.
> 
> (The current static assignment comes from the chips where they had no
>  ELD communication -- the hardware before the recent onboard Intel and
>  AMD gfx but connected somehow externally.  For such hardware, we
>  still need the static assignment.)
> 
> OTOH, we have to keep some compatibility.  And moving to the hotplug
> would break certainly some existing configuration that assumes the
> static port / device assignment.
> 
> So, a compromise would be:
> - change the behavior via either Kconfig or module option.
> - create many PCM devices statically as much as possible
> 
> The latter can be a problem in the case of AMD or Nvidia where 8 (or
> more?) ports may exist.  The former is, of course, messy and confusing
> for users, too.

Fwiw, Mengdong has some patches that are work in progress for the
dynamic PCM creation/removal as part of the topology work. The topology
has to support DSP FW that can load/unload different services that may
also include a dynamically registered PCM/compressed PCM device.

Tanu, what's your take on the effort for dynamically created PCMs
support for pulseaudio ? Btw, the topology core now also dynamically
creates/removes mixer controls, can PA handle this atm ?

Thanks

Liam

---------------------------------------------------------------------
Intel Corporation (UK) Limited
Registered No. 1134945 (England)
Registered Office: Pipers Way, Swindon SN3 1RJ
VAT No: 860 2173 47

This e-mail and any attachments may contain confidential material for
the sole use of the intended recipient(s). Any review or distribution
by others is strictly prohibited. If you are not the intended
recipient, please contact the sender and delete all copies.