[Intel-gfx] [PATCH 1/4] drm/i915: read dpcd 0 - 12 & link_status always

[Daniel Vetter]

On Tue, Sep 01, 2015 at 01:16:49PM +0300, Jani Nikula wrote:
> On Thu, 27 Aug 2015, Sivakumar Thulasimani <sivakumar.thulasimani at intel.com> wrote:
> > From: "Thulasimani,Sivakumar" <sivakumar.thulasimani at intel.com>
> >
> > Compliance requires the driver to read dpcd register 0 to 12 and
> > registers 0x200 to 0x205 to be read always.
> > Current code performs dpcd read for short pulse interrupts only
> > if the sink is enabled. This patch forces read for link status
> > and registers 0 to 12.
> 
> While this seems a bit silly from the driver perspective, I don't see it
> doing much harm either.

I don't think this is silly, but fixing it like this might be - currently
we don't do _any_ detection of sink ports, so if you have a hub with two
outputs and then plug in another one and plug out the first userspace
won't reprobe. So probably what we should be doing is not just read the
dpcd, but actually look at it, figure out whether something has changed
and make sure we send out the uevent even if the hpd line stays unchanged
on short pulses to make userspace aware of the changes.

Punting on this for now since I suspect there's a bigger story to be had
here ...
-Daniel

> 
> Note that We do read dpcd 0 to 14 no matter what the spec says.
> 
> Reviewed-by: Jani Nikula <jani.nikula at intel.com>
> 
> >
> > Signed-off-by: Sivakumar Thulasimani <sivakumar.thulasimani at intel.com>
> > ---
> >  drivers/gpu/drm/i915/intel_dp.c |   12 ++++++------
> >  1 file changed, 6 insertions(+), 6 deletions(-)
> >
> > diff --git a/drivers/gpu/drm/i915/intel_dp.c b/drivers/gpu/drm/i915/intel_dp.c
> > index 8a66a44..76561e0 100644
> > --- a/drivers/gpu/drm/i915/intel_dp.c
> > +++ b/drivers/gpu/drm/i915/intel_dp.c
> > @@ -4374,12 +4374,6 @@ intel_dp_check_link_status(struct intel_dp *intel_dp)
> >  
> >  	WARN_ON(!drm_modeset_is_locked(&dev->mode_config.connection_mutex));
> >  
> > -	if (!intel_encoder->base.crtc)
> > -		return;
> > -
> > -	if (!to_intel_crtc(intel_encoder->base.crtc)->active)
> > -		return;
> > -
> >  	/* Try to read receiver status if the link appears to be up */
> >  	if (!intel_dp_get_link_status(intel_dp, link_status)) {
> >  		return;
> > @@ -4390,6 +4384,12 @@ intel_dp_check_link_status(struct intel_dp *intel_dp)
> >  		return;
> >  	}
> >  
> > +	if (!intel_encoder->base.crtc)
> > +		return;
> > +
> > +	if (!to_intel_crtc(intel_encoder->base.crtc)->active)
> > +		return;
> > +
> >  	/* Try to read the source of the interrupt */
> >  	if (intel_dp->dpcd[DP_DPCD_REV] >= 0x11 &&
> >  	    intel_dp_get_sink_irq(intel_dp, &sink_irq_vector)) {
> > -- 
> > 1.7.9.5
> >
> 
> -- 
> Jani Nikula, Intel Open Source Technology Center
> _______________________________________________
> Intel-gfx mailing list
> Intel-gfx at lists.freedesktop.org
> http://lists.freedesktop.org/mailman/listinfo/intel-gfx

-- 
Daniel Vetter
Software Engineer, Intel Corporation
http://blog.ffwll.ch