[Intel-gfx] [PATCH 4/6] drm/i915: drm/i915: Check live status before reading edid

[Sonika Jindal]

The Bspec is very clear that Live status must be checked about before
trying to read EDID over DDC channel. This patch makes sure that HDMI
EDID is read only when live status us up.

The live status doesn't seem to perform very consistent across various
platforms when tested with different monitors. The reason behind that is
some monitors are late to provide right voltage to set live_status up.
So, after getting the interrupt, for a small duration, live status reg
fluctuates, and then settles down showing the correct staus.

This is explained here in, in a rough way:
HPD line  ________________
			 |\ T1 = Monitor Hotplug causing IRQ
			 | \______________________________________
			 | |
                         | |
			 | |   T2 = Live status is stable 
			 | |  _____________________________________
			 | | /|
Live status _____________|_|/ |
			 | |  |
			 | |  |
			 | |  |
			T0 T1  T2

(Between T1 and T2 Live status fluctuates or can be even low, depending on
 the monitor)

After several experiments, we have concluded that a max delay
of 30ms is enough to allow the live status to settle down with
most of the monitors. This total delay of 30ms has been split into
a resolution of 3 retries of 10ms each, for the better cases.

This delay is kept at 30ms, keeping in consideration that, HDCP compliance
expect the HPD handler to respond a plug out in 100ms, by disabling the port.

v2: Adding checks for VLV/CHV as well. Reusing old ibx and g4x functions
to check digital port status. Adding a separate function to get bxt live
status (Daniel)
v3: Using intel_encoder->hpd_pin to check the live status (Siva)
Moving the live status read to intel_hdmi_probe and passing parameter
to read/not to read the edid. (me)
v4:
* Added live status check for all platforms using
intel_digital_port_connected.
* Rebased on top of Jani's DP cleanup series
* Some monitors take time in setting the live status. So retry for few
times if this is a connect HPD

Signed-off-by: Sonika Jindal <sonika.jindal at intel.com>
---
 drivers/gpu/drm/i915/intel_hdmi.c |   35 ++++++++++++++++++++++++++++-------
 1 file changed, 28 insertions(+), 7 deletions(-)

diff --git a/drivers/gpu/drm/i915/intel_hdmi.c b/drivers/gpu/drm/i915/intel_hdmi.c
index 1eda71a..d82887b 100644
--- a/drivers/gpu/drm/i915/intel_hdmi.c
+++ b/drivers/gpu/drm/i915/intel_hdmi.c
@@ -1329,22 +1329,23 @@ intel_hdmi_unset_edid(struct drm_connector *connector)
 }
 
 static bool
-intel_hdmi_set_edid(struct drm_connector *connector)
+intel_hdmi_set_edid(struct drm_connector *connector, bool force)
 {
 	struct drm_i915_private *dev_priv = to_i915(connector->dev);
 	struct intel_hdmi *intel_hdmi = intel_attached_hdmi(connector);
 	struct intel_encoder *intel_encoder =
 		&hdmi_to_dig_port(intel_hdmi)->base;
 	enum intel_display_power_domain power_domain;
-	struct edid *edid;
+	struct edid *edid = NULL;
 	bool connected = false;
 
 	power_domain = intel_display_port_power_domain(intel_encoder);
 	intel_display_power_get(dev_priv, power_domain);
 
-	edid = drm_get_edid(connector,
-			    intel_gmbus_get_adapter(dev_priv,
-						    intel_hdmi->ddc_bus));
+	if (force)
+		edid = drm_get_edid(connector,
+				    intel_gmbus_get_adapter(dev_priv,
+				    intel_hdmi->ddc_bus));
 
 	intel_display_power_put(dev_priv, power_domain);
 
@@ -1374,6 +1375,26 @@ void intel_hdmi_probe(struct intel_encoder *intel_encoder)
 			enc_to_intel_hdmi(&intel_encoder->base);
 	struct intel_connector *intel_connector =
 				intel_hdmi->attached_connector;
+	struct drm_i915_private *dev_priv = to_i915(intel_encoder->base.dev);
+	bool live_status = false;
+	unsigned int retry = 3;
+
+	live_status = intel_digital_port_connected(dev_priv,
+						   hdmi_to_dig_port(intel_hdmi));
+	if (!intel_connector->detect_edid && live_status == false) {
+		/*
+		 * Hotplug had occurred and old status was disconnected,
+		 * so it might be possible that live status is not set,
+		 * so retry for few times
+		 */
+		do {
+			mdelay(10);
+			live_status = intel_digital_port_connected(dev_priv,
+						hdmi_to_dig_port(intel_hdmi));
+			if (live_status)
+				break;
+		} while (retry--);
+	}
 
 	/*
 	 * We are here, means there is a hotplug or a force
@@ -1381,7 +1402,7 @@ void intel_hdmi_probe(struct intel_encoder *intel_encoder)
 	 * DDC bus to check the current status of HDMI.
 	 */
 	intel_hdmi_unset_edid(&intel_connector->base);
-	if (intel_hdmi_set_edid(&intel_connector->base))
+	if (intel_hdmi_set_edid(&intel_connector->base, live_status))
 		DRM_DEBUG_DRIVER("DDC probe: got EDID\n");
 	else
 		DRM_DEBUG_DRIVER("DDC probe: no EDID\n");
@@ -1432,7 +1453,7 @@ intel_hdmi_force(struct drm_connector *connector)
 	if (connector->status != connector_status_connected)
 		return;
 
-	intel_hdmi_set_edid(connector);
+	intel_hdmi_set_edid(connector, true);
 	hdmi_to_dig_port(intel_hdmi)->base.type = INTEL_OUTPUT_HDMI;
 }
 
-- 
1.7.10.4