[Intel-gfx] [BXT MIPI PATCH v4 11/14] drm/i915/bxt: Modify BXT BLC according to VBT changes
Uma Shankar
uma.shankar at intel.com
Wed Sep 23 10:59:11 PDT 2015
From: Sunil Kamath <sunil.kamath at intel.com>
Latest VBT mentions which set of registers will be used for BLC,
as controller number field. Making use of this field in BXT
BLC implementation. Also, the registers are used in case control
pin indicates display DDI. Adding a check for this.
According to Bspec, BLC_PWM_*_2 uses the display utility pin for output.
To use backlight 2, enable the utility pin with mode = PWM
v2: Jani's review comments
addressed
- Add a prefix _ to BXT BLC registers definitions.
- Add "bxt only" comment for u8 controller
- Remove control_pin check for DDI controller
- Check for valid controller values
- Set pipe bits in UTIL_PIN_CTL
- Enable/Disable UTIL_PIN_CTL in enable/disable_backlight()
- If BLC 2 is used, read active_low_pwm from UTIL_PIN polarity
Satheesh's review comment addressed
- If UTIL PIN is already enabled, BIOS would have programmed it. No
need to disable and enable again.
v3: Jani's review comments
- add UTIL_PIN_PIPE_MASK and UTIL_PIN_MODE_MASK
- Disable UTIL_PIN if controller 1 is used
- Mask out UTIL_PIN_PIPE_MASK and UTIL_PIN_MODE_MASK before enabling
UTIL_PIN
- check valid controller value in intel_bios.c
- add backlight.util_pin_active_low
- disable util pin before enabling
v4: Change for BXT-PO branch:
Stubbed unwanted definition which was existing before
because of DC6 patch.
UTIL_PIN_MODE_PWM (0x1b << 24)
v2: Fixed Jani's review comment.
v3: Split the backight PWM frequency programming into separate patch,
in cases BIOS doesn't initializes it.
v4: Starting afresh and not modifying existing state for backlight, as
per Jani's recommendation.
Signed-off-by: Vandana Kannan <vandana.kannan at intel.com>
Signed-off-by: Sunil Kamath <sunil.kamath at intel.com>
Signed-off-by: Uma Shankar <uma.shankar at intel.com>
---
drivers/gpu/drm/i915/i915_reg.h | 28 +++++++++----
drivers/gpu/drm/i915/intel_drv.h | 2 +
drivers/gpu/drm/i915/intel_panel.c | 76 ++++++++++++++++++++++++++++--------
3 files changed, 81 insertions(+), 25 deletions(-)
diff --git a/drivers/gpu/drm/i915/i915_reg.h b/drivers/gpu/drm/i915/i915_reg.h
index 88a16e2..519f764 100644
--- a/drivers/gpu/drm/i915/i915_reg.h
+++ b/drivers/gpu/drm/i915/i915_reg.h
@@ -3512,17 +3512,29 @@ enum skl_disp_power_wells {
#define UTIL_PIN_CTL 0x48400
#define UTIL_PIN_ENABLE (1 << 31)
+#define UTIL_PIN_PIPE(x) ((x) << 29)
+#define UTIL_PIN_PIPE_MASK (3 << 29)
+#define UTIL_PIN_MODE_PWM (1 << 24)
+#define UTIL_PIN_MODE_MASK (0xf << 24)
+#define UTIL_PIN_POLARITY (1 << 22)
+
/* BXT backlight register definition. */
-#define BXT_BLC_PWM_CTL1 0xC8250
+#define _BXT_BLC_PWM_CTL1 0xC8250
#define BXT_BLC_PWM_ENABLE (1 << 31)
#define BXT_BLC_PWM_POLARITY (1 << 29)
-#define BXT_BLC_PWM_FREQ1 0xC8254
-#define BXT_BLC_PWM_DUTY1 0xC8258
-
-#define BXT_BLC_PWM_CTL2 0xC8350
-#define BXT_BLC_PWM_FREQ2 0xC8354
-#define BXT_BLC_PWM_DUTY2 0xC8358
-
+#define _BXT_BLC_PWM_FREQ1 0xC8254
+#define _BXT_BLC_PWM_DUTY1 0xC8258
+
+#define _BXT_BLC_PWM_CTL2 0xC8350
+#define _BXT_BLC_PWM_FREQ2 0xC8354
+#define _BXT_BLC_PWM_DUTY2 0xC8358
+
+#define BXT_BLC_PWM_CTL(controller) _PIPE(controller, \
+ _BXT_BLC_PWM_CTL1, _BXT_BLC_PWM_CTL2)
+#define BXT_BLC_PWM_FREQ(controller) _PIPE(controller, \
+ _BXT_BLC_PWM_FREQ1, _BXT_BLC_PWM_FREQ2)
+#define BXT_BLC_PWM_DUTY(controller) _PIPE(controller, \
+ _BXT_BLC_PWM_DUTY1, _BXT_BLC_PWM_DUTY2)
#define PCH_GTC_CTL 0xe7000
#define PCH_GTC_ENABLE (1 << 31)
diff --git a/drivers/gpu/drm/i915/intel_drv.h b/drivers/gpu/drm/i915/intel_drv.h
index 1059283..d8ca075 100644
--- a/drivers/gpu/drm/i915/intel_drv.h
+++ b/drivers/gpu/drm/i915/intel_drv.h
@@ -182,7 +182,9 @@ struct intel_panel {
bool enabled;
bool combination_mode; /* gen 2/4 only */
bool active_low_pwm;
+ bool util_pin_active_low; /* bxt+ */
struct backlight_device *device;
+ u8 controller; /* bxt+ only */
} backlight;
void (*backlight_power)(struct intel_connector *, bool enable);
diff --git a/drivers/gpu/drm/i915/intel_panel.c b/drivers/gpu/drm/i915/intel_panel.c
index 55aad23..fafbccc 100644
--- a/drivers/gpu/drm/i915/intel_panel.c
+++ b/drivers/gpu/drm/i915/intel_panel.c
@@ -539,9 +539,10 @@ static u32 vlv_get_backlight(struct intel_connector *connector)
static u32 bxt_get_backlight(struct intel_connector *connector)
{
struct drm_device *dev = connector->base.dev;
+ struct intel_panel *panel = &connector->panel;
struct drm_i915_private *dev_priv = dev->dev_private;
- return I915_READ(BXT_BLC_PWM_DUTY1);
+ return I915_READ(BXT_BLC_PWM_DUTY(panel->backlight.controller));
}
static u32 intel_panel_get_backlight(struct intel_connector *connector)
@@ -628,8 +629,9 @@ static void bxt_set_backlight(struct intel_connector *connector, u32 level)
{
struct drm_device *dev = connector->base.dev;
struct drm_i915_private *dev_priv = dev->dev_private;
+ struct intel_panel *panel = &connector->panel;
- I915_WRITE(BXT_BLC_PWM_DUTY1, level);
+ I915_WRITE(BXT_BLC_PWM_DUTY(panel->backlight.controller), level);
}
static void
@@ -761,12 +763,20 @@ static void bxt_disable_backlight(struct intel_connector *connector)
{
struct drm_device *dev = connector->base.dev;
struct drm_i915_private *dev_priv = dev->dev_private;
- u32 tmp;
+ struct intel_panel *panel = &connector->panel;
+ u32 tmp, val;
intel_panel_actually_set_backlight(connector, 0);
- tmp = I915_READ(BXT_BLC_PWM_CTL1);
- I915_WRITE(BXT_BLC_PWM_CTL1, tmp & ~BXT_BLC_PWM_ENABLE);
+ tmp = I915_READ(BXT_BLC_PWM_CTL(panel->backlight.controller));
+ I915_WRITE(BXT_BLC_PWM_CTL(panel->backlight.controller),
+ tmp & ~BXT_BLC_PWM_ENABLE);
+
+ if (panel->backlight.controller == 1) {
+ val = I915_READ(UTIL_PIN_CTL);
+ val &= ~UTIL_PIN_ENABLE;
+ I915_WRITE(UTIL_PIN_CTL, val);
+ }
}
void intel_panel_disable_backlight(struct intel_connector *connector)
@@ -988,16 +998,31 @@ static void bxt_enable_backlight(struct intel_connector *connector)
struct drm_device *dev = connector->base.dev;
struct drm_i915_private *dev_priv = dev->dev_private;
struct intel_panel *panel = &connector->panel;
- u32 pwm_ctl;
+ enum pipe pipe = intel_get_pipe_from_connector(connector);
+ u32 pwm_ctl, val;
+
+ /* To use 2nd set of backlight registers, utility pin has to be
+ * enabled with PWM mode.
+ * The field should only be changed when the utility pin is disabled
+ */
+ if (panel->backlight.controller == 1) {
+ val = 0;
+ if (panel->backlight.util_pin_active_low)
+ val |= UTIL_PIN_POLARITY;
+ I915_WRITE(UTIL_PIN_CTL, val | UTIL_PIN_PIPE(pipe) |
+ UTIL_PIN_MODE_PWM | UTIL_PIN_ENABLE);
+ }
- pwm_ctl = I915_READ(BXT_BLC_PWM_CTL1);
+ pwm_ctl = I915_READ(BXT_BLC_PWM_CTL(panel->backlight.controller));
if (pwm_ctl & BXT_BLC_PWM_ENABLE) {
DRM_DEBUG_KMS("backlight already enabled\n");
pwm_ctl &= ~BXT_BLC_PWM_ENABLE;
- I915_WRITE(BXT_BLC_PWM_CTL1, pwm_ctl);
+ I915_WRITE(BXT_BLC_PWM_CTL(panel->backlight.controller),
+ pwm_ctl);
}
- I915_WRITE(BXT_BLC_PWM_FREQ1, panel->backlight.max);
+ I915_WRITE(BXT_BLC_PWM_FREQ(panel->backlight.controller),
+ panel->backlight.max);
intel_panel_actually_set_backlight(connector, panel->backlight.level);
@@ -1005,9 +1030,10 @@ static void bxt_enable_backlight(struct intel_connector *connector)
if (panel->backlight.active_low_pwm)
pwm_ctl |= BXT_BLC_PWM_POLARITY;
- I915_WRITE(BXT_BLC_PWM_CTL1, pwm_ctl);
- POSTING_READ(BXT_BLC_PWM_CTL1);
- I915_WRITE(BXT_BLC_PWM_CTL1, pwm_ctl | BXT_BLC_PWM_ENABLE);
+ I915_WRITE(BXT_BLC_PWM_CTL(panel->backlight.controller), pwm_ctl);
+ POSTING_READ(BXT_BLC_PWM_CTL(panel->backlight.controller));
+ I915_WRITE(BXT_BLC_PWM_CTL(panel->backlight.controller),
+ pwm_ctl | BXT_BLC_PWM_ENABLE);
}
void intel_panel_enable_backlight(struct intel_connector *connector)
@@ -1370,12 +1396,28 @@ bxt_setup_backlight(struct intel_connector *connector, enum pipe unused)
struct intel_panel *panel = &connector->panel;
u32 pwm_ctl, val;
- pwm_ctl = I915_READ(BXT_BLC_PWM_CTL1);
- panel->backlight.active_low_pwm = pwm_ctl & BXT_BLC_PWM_POLARITY;
+ /*
+ * For BXT hard coding the Backlight controller to 0.
+ * TODO : Read the controller value from VBT and generalize
+ */
+ panel->backlight.controller = 0;
- panel->backlight.max = I915_READ(BXT_BLC_PWM_FREQ1);
- if (!panel->backlight.max)
- return -ENODEV;
+ pwm_ctl = I915_READ(BXT_BLC_PWM_CTL(panel->backlight.controller));
+
+ /* Keeping the check if controller 1 is to be programmed.
+ * This will come into affect once the VBT parsing
+ * is fixed for controller selection, and controller 1 is used
+ * for a prticular display configuration.
+ */
+ if (panel->backlight.controller == 1) {
+ val = I915_READ(UTIL_PIN_CTL);
+ panel->backlight.util_pin_active_low =
+ val & UTIL_PIN_POLARITY;
+ }
+
+ panel->backlight.active_low_pwm = pwm_ctl & BXT_BLC_PWM_POLARITY;
+ panel->backlight.max = I915_READ(
+ BXT_BLC_PWM_FREQ(panel->backlight.controller));
val = bxt_get_backlight(connector);
panel->backlight.level = intel_panel_compute_brightness(connector, val);
--
1.7.9.5
More information about the Intel-gfx
mailing list