[Intel-gfx] [PATCH 12/15] drm/i915: Convert intel_lvds to use atomic state

Maarten Lankhorst maarten.lankhorst at linux.intel.com
Tue Aug 9 15:04:11 UTC 2016


Signed-off-by: Maarten Lankhorst <maarten.lankhorst at linux.intel.com>
---
 drivers/gpu/drm/i915/intel_lvds.c | 22 ++++++++++------------
 1 file changed, 10 insertions(+), 12 deletions(-)

diff --git a/drivers/gpu/drm/i915/intel_lvds.c b/drivers/gpu/drm/i915/intel_lvds.c
index bfeec045579e..f5747a901ecc 100644
--- a/drivers/gpu/drm/i915/intel_lvds.c
+++ b/drivers/gpu/drm/i915/intel_lvds.c
@@ -141,17 +141,16 @@ static void intel_pre_enable_lvds(struct intel_encoder *encoder,
 				  struct drm_connector_state *conn_state)
 {
 	struct intel_lvds_encoder *lvds_encoder = to_lvds_encoder(&encoder->base);
-	struct drm_device *dev = encoder->base.dev;
-	struct drm_i915_private *dev_priv = to_i915(dev);
-	struct intel_crtc *crtc = to_intel_crtc(encoder->base.crtc);
-	const struct drm_display_mode *adjusted_mode = &crtc->config->base.adjusted_mode;
+	struct drm_i915_private *dev_priv = to_i915(encoder->base.dev);
+	struct intel_crtc *crtc = to_intel_crtc(pipe_config->base.crtc);
+	const struct drm_display_mode *adjusted_mode = &pipe_config->base.adjusted_mode;
 	int pipe = crtc->pipe;
 	u32 temp;
 
-	if (HAS_PCH_SPLIT(dev)) {
+	if (HAS_PCH_SPLIT(dev_priv)) {
 		assert_fdi_rx_pll_disabled(dev_priv, pipe);
 		assert_shared_dpll_disabled(dev_priv,
-					    crtc->config->shared_dpll);
+					    pipe_config->shared_dpll);
 	} else {
 		assert_pll_disabled(dev_priv, pipe);
 	}
@@ -159,7 +158,7 @@ static void intel_pre_enable_lvds(struct intel_encoder *encoder,
 	temp = I915_READ(lvds_encoder->reg);
 	temp |= LVDS_PORT_EN | LVDS_A0A2_CLKA_POWER_UP;
 
-	if (HAS_PCH_CPT(dev)) {
+	if (HAS_PCH_CPT(dev_priv)) {
 		temp &= ~PORT_TRANS_SEL_MASK;
 		temp |= PORT_TRANS_SEL_CPT(pipe);
 	} else {
@@ -172,7 +171,7 @@ static void intel_pre_enable_lvds(struct intel_encoder *encoder,
 
 	/* set the corresponsding LVDS_BORDER bit */
 	temp &= ~LVDS_BORDER_ENABLE;
-	temp |= crtc->config->gmch_pfit.lvds_border_bits;
+	temp |= pipe_config->gmch_pfit.lvds_border_bits;
 	/* Set the B0-B3 data pairs corresponding to whether we're going to
 	 * set the DPLLs for dual-channel mode or not.
 	 */
@@ -195,7 +194,7 @@ static void intel_pre_enable_lvds(struct intel_encoder *encoder,
 	if (IS_GEN4(dev_priv)) {
 		/* Bspec wording suggests that LVDS port dithering only exists
 		 * for 18bpp panels. */
-		if (crtc->config->dither && crtc->config->pipe_bpp == 18)
+		if (pipe_config->dither && pipe_config->pipe_bpp == 18)
 			temp |= LVDS_ENABLE_DITHER;
 		else
 			temp &= ~LVDS_ENABLE_DITHER;
@@ -245,12 +244,11 @@ static void intel_disable_lvds(struct intel_encoder *encoder,
 			       struct intel_crtc_state *old_crtc_state,
 			       struct drm_connector_state *old_conn_state)
 {
-	struct drm_device *dev = encoder->base.dev;
 	struct intel_lvds_encoder *lvds_encoder = to_lvds_encoder(&encoder->base);
-	struct drm_i915_private *dev_priv = to_i915(dev);
+	struct drm_i915_private *dev_priv = to_i915(encoder->base.dev);
 	i915_reg_t ctl_reg, stat_reg;
 
-	if (HAS_PCH_SPLIT(dev)) {
+	if (HAS_PCH_SPLIT(dev_priv)) {
 		ctl_reg = PCH_PP_CONTROL;
 		stat_reg = PCH_PP_STATUS;
 	} else {
-- 
2.7.4



More information about the Intel-gfx mailing list