[Intel-gfx] [GLK MIPI DSI V2 2/9] drm/i915/glk: Program new MIPI DSI PHY registers for GLK
Jani Nikula
jani.nikula at intel.com
Fri Dec 23 13:57:17 UTC 2016
On Thu, 15 Dec 2016, Madhav Chauhan <madhav.chauhan at intel.com> wrote:
> From: Deepak M <m.deepak at intel.com>
>
> Program the clk lane and tlpx time count registers
> to configure DSI PHY.
>
> v2: Addressed Jani's Review comments(renamed bit field macros)
>
> Signed-off-by: Deepak M <m.deepak at intel.com>
> Signed-off-by: Madhav Chauhan <madhav.chauhan at intel.com>
> ---
> drivers/gpu/drm/i915/i915_reg.h | 18 ++++++++++++++++++
> drivers/gpu/drm/i915/intel_dsi.c | 15 +++++++++++++++
> 2 files changed, 33 insertions(+)
>
> diff --git a/drivers/gpu/drm/i915/i915_reg.h b/drivers/gpu/drm/i915/i915_reg.h
> index 8e47b59..03858f9 100644
> --- a/drivers/gpu/drm/i915/i915_reg.h
> +++ b/drivers/gpu/drm/i915/i915_reg.h
> @@ -8550,6 +8550,24 @@ enum {
> #define LP_BYTECLK_SHIFT 0
> #define LP_BYTECLK_MASK (0xffff << 0)
>
> +#define _MIPIA_TLPX_TIME_COUNT (dev_priv->mipi_mmio_base + 0xb0a4)
> +#define _MIPIC_TLPX_TIME_COUNT (dev_priv->mipi_mmio_base + 0xb8a4)
> +#define MIPI_TLPX_TIME_COUNT(port) _MMIO_MIPI(port, _MIPIA_TLPX_TIME_COUNT, _MIPIC_TLPX_TIME_COUNT)
> +#define GLK_DPHY_TLPX_TIME_CNT_SHIFT 0
> +#define GLK_DPHY_TLPX_TIME_CNT_MASK (0xff << 0)
> +
> +#define _MIPIA_CLK_LANE_TIMING (dev_priv->mipi_mmio_base + 0xb098)
> +#define _MIPIC_CLK_LANE_TIMING (dev_priv->mipi_mmio_base + 0xb898)
> +#define MIPI_CLK_LANE_TIMING(port) _MMIO_MIPI(port, _MIPIA_CLK_LANE_TIMING, _MIPIC_CLK_LANE_TIMING)
> +#define GLK_MIPI_CLK_LANE_HS_PREP_SHIFT 0
> +#define GLK_MIPI_CLK_LANE_HS_PREP_MASK (0xff << 0)
> +#define GLK_MIPI_CLK_LANE_HS_ZERO_SHIFT 8
> +#define GLK_MIPI_CLK_LANE_HS_ZERO_MASK (0xff00 << 0)
0xff << 8
> +#define GLK_MIPI_CLK_LANE_HS_TRAIL_SHIFT 16
> +#define GLK_MIPI_CLK_LANE_HS_TRAIL_MASK (0xff0000 << 0)
0xff << 16
> +#define GLK_MIPI_CLK_LANE_HS_EXIT_SHIFT 24
> +#define GLK_MIPI_CLK_LANE_HS_EXIT_MASK (0xff000000 << 0)
0xff << 24
> +
> /* bits 31:0 */
> #define _MIPIA_LP_GEN_DATA (dev_priv->mipi_mmio_base + 0xb064)
> #define _MIPIC_LP_GEN_DATA (dev_priv->mipi_mmio_base + 0xb864)
> diff --git a/drivers/gpu/drm/i915/intel_dsi.c b/drivers/gpu/drm/i915/intel_dsi.c
> index 6b63355..b78c686 100644
> --- a/drivers/gpu/drm/i915/intel_dsi.c
> +++ b/drivers/gpu/drm/i915/intel_dsi.c
> @@ -1123,6 +1123,7 @@ static void intel_dsi_prepare(struct intel_encoder *intel_encoder,
> struct drm_i915_private *dev_priv = to_i915(dev);
> struct intel_crtc *intel_crtc = to_intel_crtc(pipe_config->base.crtc);
> struct intel_dsi *intel_dsi = enc_to_intel_dsi(encoder);
> + struct mipi_config *mipi_config = dev_priv->vbt.dsi.config;
> const struct drm_display_mode *adjusted_mode = &pipe_config->base.adjusted_mode;
> enum port port;
> unsigned int bpp = mipi_dsi_pixel_format_to_bpp(intel_dsi->pixel_format);
> @@ -1278,6 +1279,20 @@ static void intel_dsi_prepare(struct intel_encoder *intel_encoder,
> */
> I915_WRITE(MIPI_LP_BYTECLK(port), intel_dsi->lp_byte_clk);
>
> + if (IS_GEMINILAKE(dev_priv)) {
> + I915_WRITE(MIPI_TLPX_TIME_COUNT(port),
> + intel_dsi->lp_byte_clk);
> + val = ((mipi_config->ths_prepare <<
> + GLK_MIPI_CLK_LANE_HS_PREP_SHIFT) |
> + (mipi_config->ths_prepare_hszero <<
> + GLK_MIPI_CLK_LANE_HS_ZERO_SHIFT) |
> + (mipi_config->ths_trail <<
> + GLK_MIPI_CLK_LANE_HS_TRAIL_SHIFT) |
> + (mipi_config->ths_exit <<
> + GLK_MIPI_CLK_LANE_HS_EXIT_SHIFT));
> + I915_WRITE(MIPI_CLK_LANE_TIMING(port), val);
> + }
Please fix this as Ville suggested, i.e. don't look at mipi_config
directly in intel_dsi.c. See what gets done with dphy_reg.
We may change this later, but for now I think this is the right thing to
do.
BR,
Jani.
> +
> /* the bw essential for transmitting 16 long packets containing
> * 252 bytes meant for dcs write memory command is programmed in
> * this register in terms of byte clocks. based on dsi transfer
--
Jani Nikula, Intel Open Source Technology Center
More information about the Intel-gfx
mailing list