[Intel-gfx] [GLK MIPI DSI V2 3/9] drm/i915/glk: Add MIPIIO Enable/disable sequence
Chauhan, Madhav
madhav.chauhan at intel.com
Tue Dec 27 13:32:07 UTC 2016
> -----Original Message-----
> From: Nikula, Jani
> Sent: Tuesday, December 27, 2016 6:04 PM
> To: Chauhan, Madhav <madhav.chauhan at intel.com>; intel-
> gfx at lists.freedesktop.org
> Cc: Conselvan De Oliveira, Ander <ander.conselvan.de.oliveira at intel.com>;
> Saarinen, Jani <jani.saarinen at intel.com>; Konduru, Chandra
> <chandra.konduru at intel.com>; Shankar, Uma <uma.shankar at intel.com>;
> Mukherjee, Indranil <indranil.mukherjee at intel.com>; Kumar, Shobhit
> <shobhit.kumar at intel.com>; Deepak M <m.deepak at intel.com>
> Subject: RE: [GLK MIPI DSI V2 3/9] drm/i915/glk: Add MIPIIO Enable/disable
> sequence
>
> On Mon, 26 Dec 2016, "Chauhan, Madhav" <madhav.chauhan at intel.com>
> wrote:
> >> -----Original Message-----
> >> From: Nikula, Jani
> >> Sent: Friday, December 23, 2016 7:40 PM
> >> To: Chauhan, Madhav <madhav.chauhan at intel.com>; intel-
> >> gfx at lists.freedesktop.org
> >> Cc: Conselvan De Oliveira, Ander
> >> <ander.conselvan.de.oliveira at intel.com>;
> >> Saarinen, Jani <jani.saarinen at intel.com>; Konduru, Chandra
> >> <chandra.konduru at intel.com>; Shankar, Uma
> <uma.shankar at intel.com>;
> >> Mukherjee, Indranil <indranil.mukherjee at intel.com>; Kumar, Shobhit
> >> <shobhit.kumar at intel.com>; Deepak M <m.deepak at intel.com>;
> Chauhan,
> >> Madhav <madhav.chauhan at intel.com>
> >> Subject: Re: [GLK MIPI DSI V2 3/9] drm/i915/glk: Add MIPIIO
> >> Enable/disable sequence
> >>
> >> On Thu, 15 Dec 2016, Madhav Chauhan <madhav.chauhan at intel.com>
> >> wrote:
> >> > From: Deepak M <m.deepak at intel.com>
> >> >
> >> > v2: Addressed Jani's Review comments(renamed bit field macros)
> >> >
> >> > Signed-off-by: Deepak M <m.deepak at intel.com>
> >> > Signed-off-by: Madhav Chauhan <madhav.chauhan at intel.com>
> >> > ---
> >> > drivers/gpu/drm/i915/intel_dsi.c | 134
> >> > +++++++++++++++++++++++++++++++++++++++
> >> > 1 file changed, 134 insertions(+)
> >> >
> >> > diff --git a/drivers/gpu/drm/i915/intel_dsi.c
> >> > b/drivers/gpu/drm/i915/intel_dsi.c
> >> > index b78c686..c0697e9 100644
> >> > --- a/drivers/gpu/drm/i915/intel_dsi.c
> >> > +++ b/drivers/gpu/drm/i915/intel_dsi.c
> >> > @@ -357,6 +357,134 @@ static bool intel_dsi_compute_config(struct
> >> intel_encoder *encoder,
> >> > return true;
> >> > }
> >> >
> >> > +static void intel_dsi_disable_mipiio(struct intel_encoder *encoder) {
> >> > + struct drm_i915_private *dev_priv = to_i915(encoder->base.dev);
> >> > + struct intel_dsi *intel_dsi = enc_to_intel_dsi(&encoder->base);
> >> > + enum port port;
> >> > + u32 tmp;
> >> > +
> >> > + /* Put the IO into reset */
> >> > + tmp = I915_READ(MIPI_CTRL(PORT_A));
> >> > + tmp &= ~GLK_MIPIIO_RESET_RELEASED;
> >> > + I915_WRITE(MIPI_CTRL(PORT_A), tmp);
> >> > +
> >> > + /* Wait for MIPI PHY status bit to unset */
> >> > + for_each_dsi_port(port, intel_dsi->ports) {
> >> > + if (intel_wait_for_register(dev_priv,
> >> > + MIPI_CTRL(port),
> >> > + GLK_PHY_STATUS_PORT_READY, 0, 20))
> >> > + DRM_ERROR("PHY is not turning OFF\n");
> >> > + }
> >> > +
> >> > + /* Clear MIPI mode */
> >> > + for_each_dsi_port(port, intel_dsi->ports) {
> >> > + tmp = I915_READ(MIPI_CTRL(port));
> >> > + tmp &= ~GLK_MIPIIO_ENABLE;
> >> > + I915_WRITE(MIPI_CTRL(port), tmp);
> >> > + }
> >> > +}
> >> > +
> >> > +static void intel_dsi_enable_mipiio(struct intel_encoder *encoder) {
> >> > + struct drm_i915_private *dev_priv = to_i915(encoder->base.dev);
> >> > + struct intel_dsi *intel_dsi = enc_to_intel_dsi(&encoder->base);
> >> > + enum port port;
> >> > + u32 tmp, val;
> >> > +
> >> > + /* Put the IO into reset */
> >> > + tmp = I915_READ(MIPI_CTRL(PORT_A));
> >> > + tmp &= ~GLK_MIPIIO_RESET_RELEASED;
> >> > + I915_WRITE(MIPI_CTRL(PORT_A), tmp);
> >> > +
> >> > + /* Program LP Wake */
> >> > + for_each_dsi_port(port, intel_dsi->ports) {
> >> > + tmp = I915_READ(MIPI_CTRL(port));
> >> > + tmp &= ~GLK_LP_WAKE;
> >> > + I915_WRITE(MIPI_CTRL(port), tmp);
> >> > + }
> >> > +
> >> > + /* Set the MIPI mode */
> >> > + for_each_dsi_port(port, intel_dsi->ports) {
> >> > + tmp = I915_READ(MIPI_CTRL(port));
> >> > + I915_WRITE(MIPI_CTRL(port), tmp | GLK_MIPIIO_ENABLE);
> >> > + }
> >> > +
> >> > + /* Wait for Pwr ACK */
> >> > + for_each_dsi_port(port, intel_dsi->ports) {
> >> > + if (intel_wait_for_register(dev_priv,
> >> > + MIPI_CTRL(port),
> >> GLK_MIPIIO_PORT_POWERED,
> >> > + GLK_MIPIIO_PORT_POWERED, 20))
> >> > + DRM_ERROR("Power ACK not received\n");
> >> > + }
> >> > +
> >> > + /* Wait for MIPI PHY status bit to set */
> >> > + for_each_dsi_port(port, intel_dsi->ports) {
> >> > + if (intel_wait_for_register(dev_priv,
> >> > + MIPI_CTRL(port),
> >> GLK_MIPIIO_PORT_POWERED,
> >> > + GLK_MIPIIO_PORT_POWERED, 20))
> >> > + DRM_ERROR("PHY is not ON\n");
> >> > + }
> >> > +
> >> > + /* Get IO out of reset */
> >> > + tmp = I915_READ(MIPI_CTRL(PORT_A));
> >> > + I915_WRITE(MIPI_CTRL(PORT_A), tmp |
> >> GLK_MIPIIO_RESET_RELEASED);
> >> > +
> >> > + /* Get IO out of Low power state*/
> >> > + for_each_dsi_port(port, intel_dsi->ports) {
> >> > + if (!(I915_READ(MIPI_DEVICE_READY(port)) &
> >> DEVICE_READY)) {
> >> > + val = I915_READ(MIPI_DEVICE_READY(port));
> >> > + val &= ~ULPS_STATE_MASK;
> >> > + val |= DEVICE_READY;
> >> > + I915_WRITE(MIPI_DEVICE_READY(port), val);
> >> > + usleep_range(10, 15);
> >> > + }
> >> > +
> >> > + /* Enter ULPS */
> >> > + val = I915_READ(MIPI_DEVICE_READY(port));
> >> > + val &= ~ULPS_STATE_MASK;
> >> > + val |= (ULPS_STATE_ENTER | DEVICE_READY);
> >> > + I915_WRITE(MIPI_DEVICE_READY(port), val);
> >> > +
> >> > + /* Wait for ULPS Not active */
> >> > + if (intel_wait_for_register(dev_priv,
> >> > + MIPI_CTRL(port), GLK_ULPS_NOT_ACTIVE,
> >> > + GLK_ULPS_NOT_ACTIVE, 20))
> >> > +
> >> > + /* Exit ULPS */
> >> > + val = I915_READ(MIPI_DEVICE_READY(port));
> >> > + val &= ~ULPS_STATE_MASK;
> >> > + val |= (ULPS_STATE_EXIT | DEVICE_READY);
> >> > + I915_WRITE(MIPI_DEVICE_READY(port), val);
> >> > +
> >> > + /* Enter Normal Mode */
> >> > + val = I915_READ(MIPI_DEVICE_READY(port));
> >> > + val &= ~ULPS_STATE_MASK;
> >> > + val |= (ULPS_STATE_NORMAL_OPERATION | DEVICE_READY);
> >> > + I915_WRITE(MIPI_DEVICE_READY(port), val);
> >> > +
> >> > + tmp = I915_READ(MIPI_CTRL(port));
> >> > + tmp &= ~GLK_LP_WAKE;
> >> > + I915_WRITE(MIPI_CTRL(port), tmp);
> >> > + }
> >> > +
> >> > + /* Wait for Stop state */
> >> > + for_each_dsi_port(port, intel_dsi->ports) {
> >> > + if (intel_wait_for_register(dev_priv,
> >> > + MIPI_CTRL(port),
> >> GLK_DATA_LANE_STOP_STATE,
> >> > + GLK_DATA_LANE_STOP_STATE, 20))
> >> > + DRM_ERROR("Date lane not in STOP state\n");
> >> > + }
> >> > +
> >> > + /* Wait for AFE LATCH */
> >> > + for_each_dsi_port(port, intel_dsi->ports) {
> >> > + if (intel_wait_for_register(dev_priv,
> >> > + BXT_MIPI_PORT_CTRL(port), AFE_LATCHOUT,
> >> > + AFE_LATCHOUT, 20))
> >> > + DRM_ERROR("D-PHY not entering LP-11 state\n");
> >> > + }
> >> > +}
> >> > +
> >>
> >> I'm wondering if these should just be GLK versions of
> >> intel_dsi_device_ready and intel_dsi_clear_device_ready. It seems
> >> totally wrong that you're doing device ready stuff twice on GLK...
> >
> > Agree. Don't need to call intel_dsi_device_ready for GLK, as device ready is
> already done inside enable_io.
> > Will do following :
> > If(!IS_GEMINILAKE(dev_priv)
> > intel_dsi_device_ready(encoder);
> >
> >>
> >>
> >> > static void bxt_dsi_device_ready(struct intel_encoder *encoder) {
> >> > struct drm_i915_private *dev_priv = to_i915(encoder->base.dev);
> >> @@
> >> > -559,6 +687,9 @@ static void intel_dsi_pre_enable(struct
> >> > intel_encoder *encoder,
> >> >
> >> > intel_dsi_prepare(encoder, pipe_config);
> >> >
> >> > + if (IS_GEMINILAKE(dev_priv))
> >> > + intel_dsi_enable_mipiio(encoder);
> >> > +
> >> > /* Panel Enable over CRC PMIC */
> >> > if (intel_dsi->gpio_panel)
> >> > gpiod_set_value_cansleep(intel_dsi->gpio_panel, 1); @@ -
> >> 699,6
> >> > +830,9 @@ static void intel_dsi_clear_device_ready(struct
> >> > +intel_encoder
> >> *encoder)
> >> > usleep_range(2000, 2500);
> >> > }
> >> >
> >> > + if (IS_GEMINILAKE(dev_priv))
> >> > + intel_dsi_disable_mipiio(encoder);
> >> > +
> >>
> >> When you're doing enable/disable of something, they should be called
> >> from the corresponding functions in the enable/disable paths. But
> >> this is just a general remark, if we conclude that these should be
> >> alternative device ready/unready calls instead.
> >
> > Yes agree, intel_dsi_disable_mipiio should be called from
> > intel_dsi_post_disable after intel_dsi_clear_device_ready and before
> intel_disable_dsi_pll Will do these changes in next series.
>
> I meant, how about renaming intel_dsi_enable_mipiio to
> glk_dsi_device_ready, and making intel_dsi_device_ready call
> glk_dsi_device_ready for GLK.
>
> Then rename intel_dsi_clear_device_ready to vlv_dsi_clear_device_ready
> and intel_dsi_disable_mipiio to glk_dsi_clear_device_ready, and add a new
> intel_dsi_clear_device_ready wrapper to call vlv_dsi_clear_device_ready for
> VLV/CHV/BXT, and glk_dsi_clear_device_ready for GLK.
>
> How does that sound?
That's good input. It will align the code to the platforms.
For glk_dsi_clear_device_ready, we need to 1. Disable MIPI IO, 2. Enter LP
Shouldn't we add 2 separate functions for 1,2 and call them inside glk_dsi_clear_device_ready, it will make code readable/modularize as per BSPEC??
>
>
> BR,
> Jani.
>
> >>
> >> BR,
> >> Jani.
> >>
> >>
> >> > intel_disable_dsi_pll(encoder);
> >> > }
> >>
> >> --
> >> Jani Nikula, Intel Open Source Technology Center
>
> --
> Jani Nikula, Intel Open Source Technology Center
More information about the Intel-gfx
mailing list