[Intel-gfx] [PATCH 01/11] drm/i915: Decouple GuC log setup from verbosity parameter

[Goel, Akash]

On 6/27/2016 8:30 PM, Tvrtko Ursulin wrote:
>
> On 27/06/16 13:16, akash.goel at intel.com wrote:
>> From: Sagar Arun Kamble <sagar.a.kamble at intel.com>
>>
>> GuC Log buffer allocation was tied up with verbosity level kernel
>> parameter
>> i915.guc_log_level. User could be given a provision to enable logging at
>> runtime and not necessarily during load time only. This patch will
>> perform
>> allocation of shared log buffer always but will initially enable
>> logging on
>> GuC side through init params based on i915.guc_log_level.
>>
>> Signed-off-by: Sagar Arun Kamble <sagar.a.kamble at intel.com>
>> Signed-off-by: Akash Goel <akash.goel at intel.com>
>> ---
>>   drivers/gpu/drm/i915/i915_guc_submission.c | 3 ---
>>   drivers/gpu/drm/i915/intel_guc_loader.c    | 8 +++++---
>>   2 files changed, 5 insertions(+), 6 deletions(-)
>>
>> diff --git a/drivers/gpu/drm/i915/i915_guc_submission.c
>> b/drivers/gpu/drm/i915/i915_guc_submission.c
>> index 355b647..28a810f 100644
>> --- a/drivers/gpu/drm/i915/i915_guc_submission.c
>> +++ b/drivers/gpu/drm/i915/i915_guc_submission.c
>> @@ -826,9 +826,6 @@ static void guc_create_log(struct intel_guc *guc)
>>       unsigned long offset;
>>       uint32_t size, flags;
>>
>> -    if (i915.guc_log_level < GUC_LOG_VERBOSITY_MIN)
>> -        return;
>> -
>>       if (i915.guc_log_level > GUC_LOG_VERBOSITY_MAX)
>>           i915.guc_log_level = GUC_LOG_VERBOSITY_MAX;
>>
>> diff --git a/drivers/gpu/drm/i915/intel_guc_loader.c
>> b/drivers/gpu/drm/i915/intel_guc_loader.c
>> index 8fe96a2..db3c897 100644
>> --- a/drivers/gpu/drm/i915/intel_guc_loader.c
>> +++ b/drivers/gpu/drm/i915/intel_guc_loader.c
>> @@ -173,11 +173,13 @@ static void set_guc_init_params(struct
>> drm_i915_private *dev_priv)
>>       params[GUC_CTL_FEATURE] |= GUC_CTL_DISABLE_SCHEDULER |
>>               GUC_CTL_VCS2_ENABLED;
>>
>> -    if (i915.guc_log_level >= 0) {
>> -        params[GUC_CTL_LOG_PARAMS] = guc->log_flags;
>> +    params[GUC_CTL_LOG_PARAMS] = guc->log_flags;
>> +
>> +    if (i915.guc_log_level >= 0)
>>           params[GUC_CTL_DEBUG] =
>>               i915.guc_log_level << GUC_LOG_VERBOSITY_SHIFT;
>> -    }
>> +    else
>> +        params[GUC_CTL_DEBUG] = GUC_LOG_DISABLED;
>>
>>       if (guc->ads_obj) {
>>           u32 ads = (u32)i915_gem_obj_ggtt_offset(guc->ads_obj)
>>
>
> I did not manage to understand what is the benefit of always allocating
> the log buffer? If the user never enables logging it just wasted 11
> pages of memory, correct?
>
Yes if User never enables the logging at runtime, 11 RAM pages will be 
wasted.

Currently the pages are permanently pinned in GGTT also.
The GGTT address of log buffer is passed in the GuC firmware init 
params, at firmware loading time.

Probably this can be circumvented, if pages can be pinned right before
enabling logging (but using the same GGTT address).

> Looking at the later patches in the series, could you instead create the
> log buffer when logging is enabled via debugfs or implicitly via the
> relayfs access?
>
> Or is the problem then that you would then have to reset the GuC to
> activate it?

Yes GuC would have to be reset & firmware needs to be reloaded to pass 
the log buffer address.

Best regards
Akash

>
> Regards,
>
> Tvrtko