[Intel-gfx] [PATCH] drm/i915: Remove PIPE_CONF_CHECK_I_ALT

[Daniel Vetter]

On Wed, Mar 30, 2016 at 02:09:11PM +0300, Jani Nikula wrote:
> On Wed, 30 Mar 2016, Daniel Vetter <daniel.vetter at ffwll.ch> wrote:
> > And move the comment to the right macro. This was mixed up in
> >
> > commit cfb23ed622d040619abb91e625fcba74d356b8a8
> > Author: Maarten Lankhorst <maarten.lankhorst at linux.intel.com>
> > Date:   Tue Jul 14 12:17:40 2015 +0200
> >
> >     drm/i915: Allow fuzzy matching in pipe_config_compare, v2
> >
> > v2: Rebase.
> >
> > Cc: Maarten Lankhorst <maarten.lankhorst at linux.intel.com>
> > Cc: Daniel Stone <daniels at collabora.com>
> > Acked-by: Maarten Lankhorst <maarten.lankhorst at linux.intel.com>
> > Signed-off-by: Daniel Vetter <daniel.vetter at intel.com>
> 
> Didn't read the history, but the change is sane.
> 
> Reviewed-by: Jani Nikula <jani.nikula at intel.com>

Queued for -next, thanks for the patch.
-Daniel

> 
> > ---
> >  drivers/gpu/drm/i915/intel_display.c | 22 +++++-----------------
> >  1 file changed, 5 insertions(+), 17 deletions(-)
> >
> > diff --git a/drivers/gpu/drm/i915/intel_display.c b/drivers/gpu/drm/i915/intel_display.c
> > index 29aa64be1f03..fec6392dfc02 100644
> > --- a/drivers/gpu/drm/i915/intel_display.c
> > +++ b/drivers/gpu/drm/i915/intel_display.c
> > @@ -12569,6 +12569,11 @@ intel_pipe_config_compare(struct drm_device *dev,
> >  		ret = false; \
> >  	}
> >  
> > +/* This is required for BDW+ where there is only one set of registers for
> > + * switching between high and low RR.
> > + * This macro can be used whenever a comparison has to be made between one
> > + * hw state and multiple sw state variables.
> > + */
> >  #define PIPE_CONF_CHECK_M_N_ALT(name, alt_name) \
> >  	if (!intel_compare_link_m_n(&current_config->name, \
> >  				    &pipe_config->name, adjust) && \
> > @@ -12596,22 +12601,6 @@ intel_pipe_config_compare(struct drm_device *dev,
> >  		ret = false; \
> >  	}
> >  
> > -/* This is required for BDW+ where there is only one set of registers for
> > - * switching between high and low RR.
> > - * This macro can be used whenever a comparison has to be made between one
> > - * hw state and multiple sw state variables.
> > - */
> > -#define PIPE_CONF_CHECK_I_ALT(name, alt_name) \
> > -	if ((current_config->name != pipe_config->name) && \
> > -		(current_config->alt_name != pipe_config->name)) { \
> > -			INTEL_ERR_OR_DBG_KMS("mismatch in " #name " " \
> > -				  "(expected %i or %i, found %i)\n", \
> > -				  current_config->name, \
> > -				  current_config->alt_name, \
> > -				  pipe_config->name); \
> > -			ret = false; \
> > -	}
> > -
> >  #define PIPE_CONF_CHECK_FLAGS(name, mask)	\
> >  	if ((current_config->name ^ pipe_config->name) & (mask)) { \
> >  		INTEL_ERR_OR_DBG_KMS("mismatch in " #name "(" #mask ") " \
> > @@ -12736,7 +12725,6 @@ intel_pipe_config_compare(struct drm_device *dev,
> >  #undef PIPE_CONF_CHECK_X
> >  #undef PIPE_CONF_CHECK_I
> >  #undef PIPE_CONF_CHECK_P
> > -#undef PIPE_CONF_CHECK_I_ALT
> >  #undef PIPE_CONF_CHECK_FLAGS
> >  #undef PIPE_CONF_CHECK_CLOCK_FUZZY
> >  #undef PIPE_CONF_QUIRK
> 
> -- 
> Jani Nikula, Intel Open Source Technology Center
> _______________________________________________
> Intel-gfx mailing list
> Intel-gfx at lists.freedesktop.org
> https://lists.freedesktop.org/mailman/listinfo/intel-gfx

-- 
Daniel Vetter
Software Engineer, Intel Corporation
http://blog.ffwll.ch