[Intel-gfx] [PATCH 3/7] drm/i915: Spin opportunistically in wait_for

[Ville Syrjälä]

On Tue, May 17, 2016 at 06:43:24PM +0300, Mika Kuoppala wrote:
> Usually the condition we are after appears within very short time.
> Spin few times before going into sleep. With this approximately
> half of the wait_for in init path will take the fast path without
> sleeping.
> 
> Signed-off-by: Mika Kuoppala <mika.kuoppala at intel.com>
> ---
>  drivers/gpu/drm/i915/intel_drv.h | 14 ++++++++++----
>  1 file changed, 10 insertions(+), 4 deletions(-)
> 
> diff --git a/drivers/gpu/drm/i915/intel_drv.h b/drivers/gpu/drm/i915/intel_drv.h
> index 488141929a7a..c225605c727c 100644
> --- a/drivers/gpu/drm/i915/intel_drv.h
> +++ b/drivers/gpu/drm/i915/intel_drv.h
> @@ -39,7 +39,7 @@
>  #include <drm/drm_atomic.h>
>  
>  /**
> - * _wait_for_ms - magic (register) wait macro
> + * __wait_for_ms - magic (register) wait macro
>   *
>   * Does the right thing for modeset paths when run under kdgb or similar atomic
>   * contexts. Note that it's important that we check the condition again after
> @@ -50,17 +50,22 @@
>   * drm_can_sleep() can be removed and in_atomic()/!in_atomic() asserts
>   * added.
>   */
> -#define _wait_for_ms(COND, TIMEOUT_MS, SLEEP_US) ({ \
> +#define __wait_for_ms(COND, TIMEOUT_MS, SLEEP_US, SPIN_COUNT) ({	\
>  	const unsigned long timeout__ =					\
>  		jiffies + msecs_to_jiffies(TIMEOUT_MS) + 1;		\
> +	unsigned int c__ = 0;						\
>  	int ret__ = 0;							\
> +									\
>  	while (!(COND)) {						\
>  		if (time_after(jiffies, timeout__)) {			\
>  			if (!(COND))					\
>  				ret__ = -ETIMEDOUT;			\
>  			break;						\
>  		}							\
> -		if ((SLEEP_US) && drm_can_sleep()) {			\
> +									\
> +		if (++c__ > (SPIN_COUNT) &&				\
> +		    (SLEEP_US) &&					\
> +		    drm_can_sleep()) {					\
>  			usleep_range((SLEEP_US), (SLEEP_US) * 2);	\
>  		} else {						\
>  			cpu_relax();					\
> @@ -69,7 +74,8 @@
>  	ret__;								\
>  })
>  
> -#define wait_for(COND, MS)	 _wait_for_ms((COND), (MS), 1 * USEC_PER_MSEC)
> +#define wait_for(COND, MS)  __wait_for_ms((COND), (MS), 1 * USEC_PER_MSEC, 5)
> +#define _wait_for_ms(COND, MS, US)  __wait_for_ms((COND), (MS), (US), 5)

Why 5? I did some histrograms on wait_for() on my BSW (just looking
at modeset paths really), and that showed ~66% of the time we got it
right on the first check, and ~33% was completed after one sleep
iteration. The sleep duration didn't make much of a difference here,
so the current 1-2 msec is probably not at all optimal. I also tested
doing a double check intially, and IIRC that reduced the second bin
by about half. I didn't check whether further spinnign would have
helped more.

>  
>  /* If CONFIG_PREEMPT_COUNT is disabled, in_atomic() always reports false. */
>  #if defined(CONFIG_DRM_I915_DEBUG) && defined(CONFIG_PREEMPT_COUNT)
> -- 
> 2.5.0
> 
> _______________________________________________
> Intel-gfx mailing list
> Intel-gfx at lists.freedesktop.org
> https://lists.freedesktop.org/mailman/listinfo/intel-gfx

-- 
Ville Syrjälä
Intel OTC