[Intel-gfx] [PATCH 02/21] drm/i915/skl: SKL CDCLK change on modeset tracking VCO
Ville Syrjälä
ville.syrjala at linux.intel.com
Thu May 19 09:18:07 UTC 2016
On Thu, May 19, 2016 at 12:08:42PM +0300, Imre Deak wrote:
> On pe, 2016-05-13 at 23:41 +0300, ville.syrjala at linux.intel.com wrote:
> > From: Clint Taylor <clinton.a.taylor at intel.com>
> >
> > WARNING: Using ChromeOS with an eDP panel and a 4K at 60 DP monitor connected
> > to DDI1 the system will hard hang during a cold boot. Occurs when DDI1
> > is enabled when the cdclk is less then required. DP connected to DDI2
> > and HPD on either port works correctly.
> >
> > Set cdclk based on the max required pixel clock based on VCO
> > selected. Track boot vco instead of boot cdclk.
> >
> > The vco is now tracked at the atomic level and all CRTCs updated if
> > the required vco is changed. Not tested with eDP v1.4 panels that
> > require 8640 vco due to availability.
> >
> > V1: initial version
> > V2: add vco tracking in intel_dp_compute_config(), rename
> > skl_boot_cdclk.
> > V3: rebase, V2 feedback not possible as encoders are not aware of
> > atomic.
> > V4: track target vco is atomic state. modeset all CRTCs if vco changes
> > V5: rename atomic variable, cleaner if/else logic, use existing vco if
> > encoder does not return a new vco value. check_patch.pl cleanup
> > V6: simplify logic in intel_modeset_checks.
> > V7: reorder an IF for readability and whitespace fix.
> > V8: use dev_cdclk for tracking new cdclk during atomic
> > V9: correctly handle vco 8640 when crtcs==0
> > V10: Clean up if else in crtcs==0
> > V11: Rebase for new intel_dpll_mgr.c
> >
> > Reviewed-by: Ville Syrjälä <ville.syrjala at linux.intel.com>
> > Signed-off-by: Clint Taylor <clinton.a.taylor at intel.com>
> > [vsyrjala: rebased due to churn]
> > Signed-off-by: Ville Syrjälä <ville.syrjala at linux.intel.com>
>
> It has R-b already, but since I went through it in any case:
> Reviewed-by: Imre Deak <imre.deak at intel.com>
>
> A few notes below, none of them are about actual problems.
>
> > ---
> > drivers/gpu/drm/i915/i915_drv.h | 2 +-
> > drivers/gpu/drm/i915/intel_display.c | 109 +++++++++++++++++++++++++++++-----
> > drivers/gpu/drm/i915/intel_dpll_mgr.c | 9 +--
> > drivers/gpu/drm/i915/intel_drv.h | 4 ++
> > 4 files changed, 104 insertions(+), 20 deletions(-)
> >
> > diff --git a/drivers/gpu/drm/i915/i915_drv.h b/drivers/gpu/drm/i915/i915_drv.h
> > index 1ba614193cc9..b319da970c8a 100644
> > --- a/drivers/gpu/drm/i915/i915_drv.h
> > +++ b/drivers/gpu/drm/i915/i915_drv.h
> > @@ -1820,7 +1820,7 @@ struct drm_i915_private {
> > int num_fence_regs; /* 8 on pre-965, 16 otherwise */
> >
> > unsigned int fsb_freq, mem_freq, is_ddr3;
> > - unsigned int skl_boot_cdclk;
> > + unsigned int skl_vco_freq;
> > unsigned int cdclk_freq, max_cdclk_freq, atomic_cdclk_freq;
> > unsigned int max_dotclk_freq;
> > unsigned int rawclk_freq;
> > diff --git a/drivers/gpu/drm/i915/intel_display.c b/drivers/gpu/drm/i915/intel_display.c
> > index cc9a8b42fbc6..41fe18c4b761 100644
> > --- a/drivers/gpu/drm/i915/intel_display.c
> > +++ b/drivers/gpu/drm/i915/intel_display.c
> > @@ -5540,7 +5540,7 @@ static const struct skl_cdclk_entry {
> > { .freq = 675000, .vco = 8100 },
> > };
> >
> > -static unsigned int skl_cdclk_get_vco(unsigned int freq)
> > +unsigned int skl_cdclk_get_vco(unsigned int freq)
> > {
> > unsigned int i;
> >
> > @@ -5698,17 +5698,21 @@ void skl_uninit_cdclk(struct drm_i915_private *dev_priv)
> >
> > void skl_init_cdclk(struct drm_i915_private *dev_priv)
> > {
> > - unsigned int vco;
> > + unsigned int cdclk;
> >
> > /* DPLL0 not enabled (happens on early BIOS versions) */
> > if (!(I915_READ(LCPLL1_CTL) & LCPLL_PLL_ENABLE)) {
> > /* enable DPLL0 */
> > - vco = skl_cdclk_get_vco(dev_priv->skl_boot_cdclk);
> > - skl_dpll0_enable(dev_priv, vco);
> > + if (dev_priv->skl_vco_freq != 8640)
> > + dev_priv->skl_vco_freq = 8100;
>
> This seems redundant, VCO can only be either of the above two, but you
> change/fix this later in the series, so it's ok.
It can also be 0 initially. And so we just flip a coin and pick one.
>
> > + skl_dpll0_enable(dev_priv, dev_priv->skl_vco_freq);
> > + cdclk = ((dev_priv->skl_vco_freq == 8100) ? 337500 : 308570);
> > + } else {
> > + cdclk = dev_priv->cdclk_freq;
> > }
> >
> > - /* set CDCLK to the frequency the BIOS chose */
> > - skl_set_cdclk(dev_priv, dev_priv->skl_boot_cdclk);
> > + /* set CDCLK to the lowest frequency, Modeset follows */
> > + skl_set_cdclk(dev_priv, cdclk);
> >
> > /* enable DBUF power */
> > I915_WRITE(DBUF_CTL, I915_READ(DBUF_CTL) | DBUF_POWER_REQUEST);
> > @@ -5724,7 +5728,7 @@ int skl_sanitize_cdclk(struct drm_i915_private *dev_priv)
> > {
> > uint32_t lcpll1 = I915_READ(LCPLL1_CTL);
> > uint32_t cdctl = I915_READ(CDCLK_CTL);
> > - int freq = dev_priv->skl_boot_cdclk;
> > + int freq = dev_priv->cdclk_freq;
> >
> > /*
> > * check if the pre-os intialized the display
> > @@ -5748,11 +5752,7 @@ int skl_sanitize_cdclk(struct drm_i915_private *dev_priv)
> > /* All well; nothing to sanitize */
> > return false;
> > sanitize:
> > - /*
> > - * As of now initialize with max cdclk till
> > - * we get dynamic cdclk support
> > - * */
> > - dev_priv->skl_boot_cdclk = dev_priv->max_cdclk_freq;
> > +
> > skl_init_cdclk(dev_priv);
> >
> > /* we did have to sanitize */
> > @@ -9719,6 +9719,73 @@ static void broadwell_modeset_commit_cdclk(struct drm_atomic_state *old_state)
> > broadwell_set_cdclk(dev, req_cdclk);
> > }
> >
> > +static int skl_modeset_calc_cdclk(struct drm_atomic_state *state)
> > +{
> > + struct intel_atomic_state *intel_state = to_intel_atomic_state(state);
> > + struct drm_i915_private *dev_priv = to_i915(state->dev);
> > + const int max_pixclk = ilk_max_pixel_rate(state);
> > + int cdclk;
> > +
> > + /*
> > + * FIXME should also account for plane ratio
> > + * once 64bpp pixel formats are supported.
> > + */
> > +
> > + if (intel_state->cdclk_pll_vco == 8640) {
> > + /* vco 8640 */
> > + if (max_pixclk > 540000)
> > + cdclk = 617140;
> > + else if (max_pixclk > 432000)
> > + cdclk = 540000;
> > + else if (max_pixclk > 308570)
> > + cdclk = 432000;
> > + else
> > + cdclk = 308570;
> > + } else {
> > + /* VCO 8100 */
> > + if (max_pixclk > 540000)
> > + cdclk = 675000;
> > + else if (max_pixclk > 450000)
> > + cdclk = 540000;
> > + else if (max_pixclk > 337500)
> > + cdclk = 450000;
> > + else
> > + cdclk = 337500;
> > + }
> > +
> > + /*
> > + * FIXME move the cdclk caclulation to
> > + * compute_config() so we can fail gracegully.
> > + */
> > + if (cdclk > dev_priv->max_cdclk_freq) {
> > + DRM_ERROR("requested cdclk (%d kHz) exceeds max (%d kHz)\n",
> > + cdclk, dev_priv->max_cdclk_freq);
> > + cdclk = dev_priv->max_cdclk_freq;
> > + }
> > +
> > + intel_state->cdclk = intel_state->dev_cdclk = cdclk;
> > + if (!intel_state->active_crtcs)
> > + intel_state->dev_cdclk = ((intel_state->cdclk_pll_vco == 8640) ?
> > + 308570 : 337500);
> > +
> > +
> > + return 0;
> > +}
> > +
> > +static void skl_modeset_commit_cdclk(struct drm_atomic_state *old_state)
> > +{
> > + struct drm_device *dev = old_state->dev;
> > + struct drm_i915_private *dev_priv = dev->dev_private;
> > + unsigned int req_cdclk = to_intel_atomic_state(old_state)->dev_cdclk;
> > +
> > + /*
> > + * FIXME disable/enable PLL should wrap set_cdclk()
> > + */
> > + skl_set_cdclk(dev_priv, req_cdclk);
> > +
> > + dev_priv->skl_vco_freq = to_intel_atomic_state(old_state)->cdclk_pll_vco;
> > +}
> > +
> > static int haswell_crtc_compute_clock(struct intel_crtc *crtc,
> > struct intel_crtc_state *crtc_state)
> > {
> > @@ -13283,9 +13350,15 @@ static int intel_modeset_checks(struct drm_atomic_state *state)
> > * adjusted_mode bits in the crtc directly.
> > */
> > if (dev_priv->display.modeset_calc_cdclk) {
> > + if (!intel_state->cdclk_pll_vco)
> > + intel_state->cdclk_pll_vco = dev_priv->skl_vco_freq;
> > +
> > ret = dev_priv->display.modeset_calc_cdclk(state);
> > + if (ret < 0)
> > + return ret;
> >
> > - if (!ret && intel_state->dev_cdclk != dev_priv->cdclk_freq)
> > + if (intel_state->dev_cdclk != dev_priv->cdclk_freq ||
> > + intel_state->cdclk_pll_vco != dev_priv->skl_vco_freq)
> > ret = intel_modeset_all_pipes(state);
> >
> > if (ret < 0)
> > @@ -13626,7 +13699,8 @@ static int intel_atomic_commit(struct drm_device *dev,
> > drm_atomic_helper_update_legacy_modeset_state(state->dev, state);
> >
> > if (dev_priv->display.modeset_commit_cdclk &&
> > - intel_state->dev_cdclk != dev_priv->cdclk_freq)
> > + (intel_state->dev_cdclk != dev_priv->cdclk_freq ||
> > + intel_state->cdclk_pll_vco != dev_priv->skl_vco_freq))
> > dev_priv->display.modeset_commit_cdclk(state);
> >
> > intel_modeset_verify_disabled(dev);
> > @@ -15041,6 +15115,11 @@ void intel_init_display_hooks(struct drm_i915_private *dev_priv)
> > broxton_modeset_commit_cdclk;
> > dev_priv->display.modeset_calc_cdclk =
> > broxton_modeset_calc_cdclk;
> > + } else if (IS_SKYLAKE(dev_priv) || IS_KABYLAKE(dev_priv)) {
> > + dev_priv->display.modeset_commit_cdclk =
> > + skl_modeset_commit_cdclk;
> > + dev_priv->display.modeset_calc_cdclk =
> > + skl_modeset_calc_cdclk;
> > }
> >
> > switch (INTEL_INFO(dev_priv)->gen) {
> > @@ -15748,7 +15827,7 @@ static void intel_modeset_readout_hw_state(struct drm_device *dev)
> > if (crtc_state->base.active) {
> > dev_priv->active_crtcs |= 1 << crtc->pipe;
> >
> > - if (IS_BROXTON(dev_priv) || IS_BROADWELL(dev_priv))
> > + if (INTEL_GEN(dev_priv) >= 9 || IS_BROADWELL(dev_priv))
> > pixclk = ilk_pipe_pixel_rate(crtc_state);
> > else if (IS_VALLEYVIEW(dev_priv) || IS_CHERRYVIEW(dev_priv))
> > pixclk = crtc_state->base.adjusted_mode.crtc_clock;
> > diff --git a/drivers/gpu/drm/i915/intel_dpll_mgr.c b/drivers/gpu/drm/i915/intel_dpll_mgr.c
> > index c283ba4babe8..e99e306e8743 100644
> > --- a/drivers/gpu/drm/i915/intel_dpll_mgr.c
> > +++ b/drivers/gpu/drm/i915/intel_dpll_mgr.c
> > @@ -1194,6 +1194,7 @@ skl_get_dpll(struct intel_crtc *crtc, struct intel_crtc_state *crtc_state,
> > struct intel_shared_dpll *pll;
> > uint32_t ctrl1, cfgcr1, cfgcr2;
> > int clock = crtc_state->port_clock;
> > + uint32_t vco = 8100;
> >
> > /*
> > * See comment in intel_dpll_hw_state to understand why we always use 0
> > @@ -1236,17 +1237,17 @@ skl_get_dpll(struct intel_crtc *crtc, struct intel_crtc_state *crtc_state,
> > case 162000:
> > ctrl1 |= DPLL_CTRL1_LINK_RATE(DPLL_CTRL1_LINK_RATE_1620, 0);
> > break;
> > - /* TBD: For DP link rates 2.16 GHz and 4.32 GHz, VCO is 8640 which
> > - results in CDCLK change. Need to handle the change of CDCLK by
> > - disabling pipes and re-enabling them */
> > case 108000:
> > ctrl1 |= DPLL_CTRL1_LINK_RATE(DPLL_CTRL1_LINK_RATE_1080, 0);
> > + vco = 8640;
> > break;
> > case 216000:
> > ctrl1 |= DPLL_CTRL1_LINK_RATE(DPLL_CTRL1_LINK_RATE_2160, 0);
> > + vco = 8640;
> > break;
> > }
> >
> > + to_intel_atomic_state(crtc_state->base.state)->cdclk_pll_vco = vco;
>
> If VCO was previously set to 8640 (for DPLL0) and later we'd set here
> the rate for another DPLL with VCO 8100 this would incorrectly change
> the CDCLK VCO to 8100. VCO isn't actually changed at this point in the
> code though and you later fix this, so it's ok.
>
> > cfgcr1 = cfgcr2 = 0;
> > } else {
> > return NULL;
> > @@ -1639,7 +1640,7 @@ static void intel_ddi_pll_init(struct drm_device *dev)
> > int cdclk_freq;
> >
> > cdclk_freq = dev_priv->display.get_display_clock_speed(dev);
> > - dev_priv->skl_boot_cdclk = cdclk_freq;
> > + dev_priv->skl_vco_freq = skl_cdclk_get_vco(cdclk_freq);
> > if (skl_sanitize_cdclk(dev_priv))
> > DRM_DEBUG_KMS("Sanitized cdclk programmed by pre-os\n");
> > if (!(I915_READ(LCPLL1_CTL) & LCPLL_PLL_ENABLE))
> > diff --git a/drivers/gpu/drm/i915/intel_drv.h b/drivers/gpu/drm/i915/intel_drv.h
> > index 0dc2bc9c65cf..c7cb9829547e 100644
> > --- a/drivers/gpu/drm/i915/intel_drv.h
> > +++ b/drivers/gpu/drm/i915/intel_drv.h
> > @@ -304,6 +304,9 @@ struct intel_atomic_state {
> > unsigned int active_crtcs;
> > unsigned int min_pixclk[I915_MAX_PIPES];
> >
> > + /* SKL/KBL Only */
> > + unsigned int cdclk_pll_vco;
> > +
> > struct intel_shared_dpll_config shared_dpll[I915_NUM_PLLS];
> >
> > /*
> > @@ -1277,6 +1280,7 @@ void gen9_enable_dc5(struct drm_i915_private *dev_priv);
> > void skl_init_cdclk(struct drm_i915_private *dev_priv);
> > int skl_sanitize_cdclk(struct drm_i915_private *dev_priv);
> > void skl_uninit_cdclk(struct drm_i915_private *dev_priv);
> > +unsigned int skl_cdclk_get_vco(unsigned int freq);
> > void skl_enable_dc6(struct drm_i915_private *dev_priv);
> > void skl_disable_dc6(struct drm_i915_private *dev_priv);
> > void intel_dp_get_m_n(struct intel_crtc *crtc,
--
Ville Syrjälä
Intel OTC
More information about the Intel-gfx
mailing list