[Intel-gfx] [PATCH v2] drm/i915/ilk: Don't disable SSC source if it's in use
Lyude Paul
cpaul at redhat.com
Tue May 24 14:08:47 UTC 2016
Huh… so I'm going to have to take back what I said before about this. On further
observation, it looks like the "Don't disable SSC source if it's in use" patch
actually got rid of the underruns entirely, with or without the wait for a
vblank here.
On Tue, 2016-05-24 at 16:14 +0300, Ville Syrjälä wrote:
> On Mon, May 23, 2016 at 03:56:36PM -0400, Lyude wrote:
> >
> > Thanks to Ville Syrjälä for pointing me towards the cause of this issue.
> >
> > Unfortunately one of the sideaffects of having the refclk for a DPLL set
> > to SSC is that as long as it's set to SSC, the GPU will prevent us from
> > powering down any of the pipes or transcoders using it. A couple of
> > BIOSes enable SSC in both PCH_DREF_CONTROL and in the DPLL
> > configurations. This causes issues on the first modeset, since we don't
> > expect SSC to be left on and as a result, can't successfully power down
> > the pipes or the transcoders using it. Here's an example from this Dell
> > OptiPlex 990:
> >
> > [drm:intel_modeset_init] SSC enabled by BIOS, overriding VBT which says
> > disabled
> > [drm:intel_modeset_init] 2 display pipes available.
> > [drm:intel_update_cdclk] Current CD clock rate: 400000 kHz
> > [drm:intel_update_max_cdclk] Max CD clock rate: 400000 kHz
> > [drm:intel_update_max_cdclk] Max dotclock rate: 360000 kHz
> > vgaarb: device changed decodes:
> > PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
> > [drm:intel_crt_reset] crt adpa set to 0xf40000
> > [drm:intel_dp_init_connector] Adding DP connector on port C
> > [drm:intel_dp_aux_init] registering DPDDC-C bus for card0-DP-1
> > [drm:ironlake_init_pch_refclk] has_panel 0 has_lvds 0 has_ck505 0
> > [drm:ironlake_init_pch_refclk] Disabling SSC entirely
> > … later we try committing the first modeset …
> > [drm:intel_dump_pipe_config] [CRTC:26][modeset] config ffff88041b02e800 for
> > pipe A
> > [drm:intel_dump_pipe_config] cpu_transcoder: A
> > …
> > [drm:intel_dump_pipe_config] dpll_hw_state: dpll: 0xc4016001, dpll_md: 0x0,
> > fp0: 0x20e08, fp1: 0x30d07
> > [drm:intel_dump_pipe_config] planes on this crtc
> > [drm:intel_dump_pipe_config] STANDARD PLANE:23 plane: 0.0 idx: 0 enabled
> > [drm:intel_dump_pipe_config] FB:42, fb = 800x600 format = 0x34325258
> > [drm:intel_dump_pipe_config] scaler:0 src (0, 0) 800x600 dst (0, 0)
> > 800x600
> > [drm:intel_dump_pipe_config] CURSOR PLANE:25 plane: 0.1 idx: 1 disabled,
> > scaler_id = 0
> > [drm:intel_dump_pipe_config] STANDARD PLANE:27 plane: 0.1 idx: 2 disabled,
> > scaler_id = 0
> > [drm:intel_get_shared_dpll] CRTC:26 allocated PCH DPLL A
> > [drm:intel_get_shared_dpll] using PCH DPLL A for pipe A
> > [drm:ilk_audio_codec_disable] Disable audio codec on port C, pipe A
> > [drm:intel_disable_pipe] disabling pipe A
> > ------------[ cut here ]------------
> > WARNING: CPU: 1 PID: 130 at drivers/gpu/drm/i915/intel_display.c:1146
> > intel_disable_pipe+0x297/0x2d0 [i915]
> > pipe_off wait timed out
> > …
> > ---[ end trace 94fc8aa03ae139e8 ]---
> > [drm:intel_dp_link_down]
> > [drm:ironlake_crtc_disable [i915]] *ERROR* failed to disable transcoder A
> >
> > Later modesets succeed since they reset the DPLL's configuration anyway,
> > but this is enough to get stuck with a big fat warning in dmesg.
> >
> > A better solution would be to add refcounts for the SSC source, but for
> > now leaving the source clock on should suffice.
> >
> > Changes since v1:
> > - Leave the SSC source clock on instead of just shutting it off on all
> > of the DPLL configurations.
> >
> > Cc: stable at vger.kernel.org
> > Signed-off-by: Lyude <cpaul at redhat.com>
> > ---
> > Sorry about that! I misread danvet's suggestion as "disable the SSC" instead
> > of
> > "don't disable the SSC".
> >
> > drivers/gpu/drm/i915/intel_display.c | 47 +++++++++++++++++++++++++++----
> > -----
> > 1 file changed, 35 insertions(+), 12 deletions(-)
> >
> > diff --git a/drivers/gpu/drm/i915/intel_display.c
> > b/drivers/gpu/drm/i915/intel_display.c
> > index d500e6f..dff8511 100644
> > --- a/drivers/gpu/drm/i915/intel_display.c
> > +++ b/drivers/gpu/drm/i915/intel_display.c
> > @@ -8230,12 +8230,14 @@ static void ironlake_init_pch_refclk(struct
> > drm_device *dev)
> > {
> > struct drm_i915_private *dev_priv = dev->dev_private;
> > struct intel_encoder *encoder;
> > - u32 val, final;
> > + int i;
> > + u32 val, temp, final;
> > bool has_lvds = false;
> > bool has_cpu_edp = false;
> > bool has_panel = false;
> > bool has_ck505 = false;
> > bool can_ssc = false;
> > + bool using_ssc_source = false;
> >
> > /* We need to take the global config into account */
> > for_each_intel_encoder(dev, encoder) {
> > @@ -8283,9 +8285,26 @@ static void ironlake_init_pch_refclk(struct
> > drm_device *dev)
> > else
> > final |= DREF_NONSPREAD_SOURCE_ENABLE;
> >
> > - final &= ~DREF_SSC_SOURCE_MASK;
> > final &= ~DREF_CPU_SOURCE_OUTPUT_MASK;
> > - final &= ~DREF_SSC1_ENABLE;
> > +
> > + /* Check if any DPLLs are using the SSC source */
> > + for (i = 0; i < dev_priv->num_shared_dpll; i++) {
> > + temp = I915_READ(PCH_DPLL(i));
> > +
> > + if (!(temp & DPLL_VCO_ENABLE))
> > + continue;
> > +
> > + if ((temp & PLL_REF_INPUT_MASK) ==
> > + PLLB_REF_INPUT_SPREADSPECTRUMIN) {
> > + using_ssc_source = true;
> > + break;
> > + }
> > + }
> > +
> > + if (!using_ssc_source) {
> > + final &= ~DREF_SSC_SOURCE_MASK;
> > + final &= ~DREF_SSC1_ENABLE;
> > + }
> >
> > if (has_panel) {
> > final |= DREF_SSC_SOURCE_ENABLE;
> > @@ -8348,7 +8367,7 @@ static void ironlake_init_pch_refclk(struct drm_device
> > *dev)
> > POSTING_READ(PCH_DREF_CONTROL);
> > udelay(200);
> > } else {
> > - DRM_DEBUG_KMS("Disabling SSC entirely\n");
> > + DRM_DEBUG_KMS("Disabling SSC CPU output\n");
> The CPU source isn't necessarily SSC. It can come from SSC1 or from
> the non-spread source.
>
> IIRC the clock tree looks something like this:
>
> integrated
> \
> -> non-spread -> dpll non-spread
> / \
> ck505 -> cpu source -> edp pll
> /
> integrated -> ssc -> ssc1 -> dpll ssc
>
> integrated -> super ssc -> ssc4 -> dpll super ssc
>
> Maybe we should slap that diagram somewhere as a comment?
>
>
> Anyways, othewise the patch looks OK I think.
>
> As far as the original code goes, I don't actually understand it. For
> LVDS it can enable the SSC source but leave SSC1 modulator disabled.
> Not sure what's the point in using the SSC source w/ SSC1 disabled.
> I'm not sure that's even legal TBH.
>
> For eDP it can select the non-spread source but still leave the SSC
> source enabled for some reason.
>
> Also I don't understand why the has_ssc depends on ck505 on IBX. We
> only use ck505 as the non-spread source, so not really sure why
> has_ssc depends on the presence of ck505. Maybe you can only get
> ssc+non-spread sources enabled at the same time if one of them
> comes from ck505?
>
> >
> > val &= ~DREF_CPU_SOURCE_OUTPUT_MASK;
> >
> > @@ -8359,16 +8378,20 @@ static void ironlake_init_pch_refclk(struct
> > drm_device *dev)
> > POSTING_READ(PCH_DREF_CONTROL);
> > udelay(200);
> >
> > - /* Turn off the SSC source */
> > - val &= ~DREF_SSC_SOURCE_MASK;
> > - val |= DREF_SSC_SOURCE_DISABLE;
> > + if (!using_ssc_source) {
> > + DRM_DEBUG_KMS("Disabling SSC source\n");
> >
> > - /* Turn off SSC1 */
> > - val &= ~DREF_SSC1_ENABLE;
> > + /* Turn off the SSC source */
> > + val &= ~DREF_SSC_SOURCE_MASK;
> > + val |= DREF_SSC_SOURCE_DISABLE;
> >
> > - I915_WRITE(PCH_DREF_CONTROL, val);
> > - POSTING_READ(PCH_DREF_CONTROL);
> > - udelay(200);
> > + /* Turn off SSC1 */
> > + val &= ~DREF_SSC1_ENABLE;
> > +
> > + I915_WRITE(PCH_DREF_CONTROL, val);
> > + POSTING_READ(PCH_DREF_CONTROL);
> > + udelay(200);
> > + }
> > }
> >
> > BUG_ON(val != final);
> > --
> > 2.5.5
More information about the Intel-gfx
mailing list