[Intel-gfx] [RFC PATCH v3 1/7] drm/i915: setup bridge for HDMI LPE audio driver
Ville Syrjälä
ville.syrjala at linux.intel.com
Fri Nov 25 10:18:52 UTC 2016
On Fri, Nov 25, 2016 at 05:42:38AM +0000, Anand, Jerome wrote:
>
>
> > -----Original Message-----
> > From: Ville Syrjälä [mailto:ville.syrjala at linux.intel.com]
> > Sent: Thursday, November 24, 2016 7:02 PM
> > To: Anand, Jerome <jerome.anand at intel.com>
> > Cc: intel-gfx at lists.freedesktop.org; alsa-devel at alsa-project.org;
> > broonie at kernel.org; tiwai at suse.de; pierre-louis.bossart at linux.intel.com;
> > Ughreja, Rakesh A <rakesh.a.ughreja at intel.com>
> > Subject: Re: [RFC PATCH v3 1/7] drm/i915: setup bridge for HDMI LPE audio
> > driver
> >
> > On Fri, Nov 25, 2016 at 05:25:42AM +0530, Jerome Anand wrote:
> > > Enable support for HDMI LPE audio mode on Baytrail and Cherrytrail
> > > when HDaudio controller is not detected
> > >
> > > Setup minimum required resources during i915_driver_load:
> > > 1. Create a platform device to share MMIO/IRQ resources 2. Make the
> > > platform device child of i915 device for runtime PM.
> > > 3. Create IRQ chip to forward HDMI LPE audio irqs.
> > >
> > > HDMI LPE audio driver (a standalone sound driver) probes the LPE audio
> > > device and creates a new sound card.
> > >
> > > Signed-off-by: Pierre-Louis Bossart
> > > <pierre-louis.bossart at linux.intel.com>
> > > Signed-off-by: Jerome Anand <jerome.anand at intel.com>
> > > ---
> > > Documentation/gpu/i915.rst | 9 +
> > > drivers/gpu/drm/i915/Makefile | 3 +
> > > drivers/gpu/drm/i915/i915_drv.c | 8 +-
> > > drivers/gpu/drm/i915/i915_drv.h | 15 ++
> > > drivers/gpu/drm/i915/i915_irq.c | 29 +++
> > > drivers/gpu/drm/i915/i915_reg.h | 3 +
> > > drivers/gpu/drm/i915/intel_lpe_audio.c | 369
> > +++++++++++++++++++++++++++++++++
> > > include/drm/intel_lpe_audio.h | 45 ++++
> > > 8 files changed, 479 insertions(+), 2 deletions(-) create mode
> > > 100644 drivers/gpu/drm/i915/intel_lpe_audio.c
> > > create mode 100644 include/drm/intel_lpe_audio.h
> > >
> > > diff --git a/Documentation/gpu/i915.rst b/Documentation/gpu/i915.rst
> > > index 117d2ab..a671eee 100644
> > > --- a/Documentation/gpu/i915.rst
> > > +++ b/Documentation/gpu/i915.rst
> > > @@ -213,6 +213,15 @@ Video BIOS Table (VBT) .. kernel-doc::
> > > drivers/gpu/drm/i915/intel_vbt_defs.h
> > > :internal:
> > >
> > > +intel hdmi lpe audio support
> > > +----------------------------
> > > +
> > > +.. kernel-doc:: drivers/gpu/drm/i915/intel_lpe_audio.c
> > > + :doc: LPE Audio integration for HDMI or DP playback
> > > +
> > > +.. kernel-doc:: drivers/gpu/drm/i915/intel_lpe_audio.c
> > > + :internal:
> > > +
> > > Memory Management and Command Submission
> > > ========================================
> > >
> > > diff --git a/drivers/gpu/drm/i915/Makefile
> > > b/drivers/gpu/drm/i915/Makefile index 580602d..3a2369c 100644
> > > --- a/drivers/gpu/drm/i915/Makefile
> > > +++ b/drivers/gpu/drm/i915/Makefile
> > > @@ -126,6 +126,9 @@ i915-y += intel_gvt.o include $(src)/gvt/Makefile
> > > endif
> > >
> > > +# LPE Audio for VLV and CHT
> > > +i915-y += intel_lpe_audio.o
> > > +
> > > obj-$(CONFIG_DRM_I915) += i915.o
> > >
> > > CFLAGS_i915_trace_points.o := -I$(src) diff --git
> > > a/drivers/gpu/drm/i915/i915_drv.c b/drivers/gpu/drm/i915/i915_drv.c
> > > index b893e67..93811ed 100644
> > > --- a/drivers/gpu/drm/i915/i915_drv.c
> > > +++ b/drivers/gpu/drm/i915/i915_drv.c
> > > @@ -1144,7 +1144,8 @@ static void i915_driver_register(struct
> > drm_i915_private *dev_priv)
> > > if (IS_GEN5(dev_priv))
> > > intel_gpu_ips_init(dev_priv);
> > >
> > > - i915_audio_component_init(dev_priv);
> > > + if (intel_lpe_audio_init(dev_priv) < 0)
> > > + i915_audio_component_init(dev_priv);
> > >
> > > /*
> > > * Some ports require correctly set-up hpd registers for detection
> > > to @@ -1162,7 +1163,10 @@ static void i915_driver_register(struct
> > drm_i915_private *dev_priv)
> > > */
> > > static void i915_driver_unregister(struct drm_i915_private *dev_priv)
> > > {
> > > - i915_audio_component_cleanup(dev_priv);
> > > + if (HAS_LPE_AUDIO(dev_priv))
> > > + intel_lpe_audio_teardown(dev_priv);
> > > + else
> > > + i915_audio_component_cleanup(dev_priv);
> > >
> > > intel_gpu_ips_teardown();
> > > acpi_video_unregister();
> > > diff --git a/drivers/gpu/drm/i915/i915_drv.h
> > > b/drivers/gpu/drm/i915/i915_drv.h index 970e50b..2a79048 100644
> > > --- a/drivers/gpu/drm/i915/i915_drv.h
> > > +++ b/drivers/gpu/drm/i915/i915_drv.h
> > > @@ -2284,6 +2284,12 @@ struct drm_i915_private {
> > > /* Used to save the pipe-to-encoder mapping for audio */
> > > struct intel_encoder *av_enc_map[I915_MAX_PIPES];
> > >
> > > + /* necessary resource sharing with HDMI LPE audio driver. */
> > > + struct {
> > > + struct platform_device *platdev;
> > > + int irq;
> > > + } lpe_audio;
> > > +
> > > /*
> > > * NOTE: This is the dri1/ums dungeon, don't add stuff here. Your
> > patch
> > > * will be rejected. Instead look for a better place.
> > > @@ -2773,6 +2779,8 @@ intel_info(const struct drm_i915_private
> > > *dev_priv)
> > >
> > > #define HAS_POOLED_EU(dev_priv) ((dev_priv)->info.has_pooled_eu)
> > >
> > > +#define HAS_LPE_AUDIO(dev_priv) ((dev_priv)->lpe_audio.platdev !=
> > > +NULL)
> > > +
> > > #define INTEL_PCH_DEVICE_ID_MASK 0xff00
> > > #define INTEL_PCH_IBX_DEVICE_ID_TYPE 0x3b00
> > > #define INTEL_PCH_CPT_DEVICE_ID_TYPE 0x1c00
> > > @@ -3547,6 +3555,13 @@ extern int i915_restore_state(struct drm_device
> > > *dev); void i915_setup_sysfs(struct drm_i915_private *dev_priv);
> > > void i915_teardown_sysfs(struct drm_i915_private *dev_priv);
> > >
> > > +/* i915_lpe_audio.c */
> > > +int intel_lpe_audio_init(struct drm_i915_private *dev_priv); int
> > > +intel_lpe_audio_setup(struct drm_i915_private *dev_priv); void
> > > +intel_lpe_audio_teardown(struct drm_i915_private *dev_priv); void
> > > +intel_lpe_audio_irq_handler(struct drm_i915_private *dev_priv); bool
> > > +intel_lpe_audio_detect(struct drm_i915_private *dev_priv);
> > > +
> > > /* intel_i2c.c */
> > > extern int intel_setup_gmbus(struct drm_device *dev); extern void
> > > intel_teardown_gmbus(struct drm_device *dev); diff --git
> > > a/drivers/gpu/drm/i915/i915_irq.c b/drivers/gpu/drm/i915/i915_irq.c
> > > index 07ca71c..6c98b28 100644
> > > --- a/drivers/gpu/drm/i915/i915_irq.c
> > > +++ b/drivers/gpu/drm/i915/i915_irq.c
> > > @@ -1894,6 +1894,15 @@ static irqreturn_t valleyview_irq_handler(int irq,
> > void *arg)
> > > valleyview_pipestat_irq_ack(dev_priv, iir, pipe_stats);
> > >
> > > /*
> > > + * LPE audio interrupts are only enabled on Baytrail and
> > > + * CherryView platforms without HDaudio
> > > + */
> > > + if (iir & (I915_LPE_PIPE_A_INTERRUPT |
> > > + I915_LPE_PIPE_B_INTERRUPT |
> > > + I915_LPE_PIPE_C_INTERRUPT))
> >
> > No pipe C on vlv.
> >
>
> OK
>
> > > + intel_lpe_audio_irq_handler(dev_priv);
> > > +
> > > + /*
> > > * VLV_IIR is single buffered, and reflects the level
> > > * from PIPESTAT/PORT_HOTPLUG_STAT, hence clear it last.
> > > */
> > > @@ -1974,6 +1983,15 @@ static irqreturn_t cherryview_irq_handler(int irq,
> > void *arg)
> > > valleyview_pipestat_irq_ack(dev_priv, iir, pipe_stats);
> > >
> > > /*
> > > + * LPE audio interrupts are only enabled on Baytrail and
> > > + * CherryView platforms without HDaudio
> > > + */
> > > + if (iir & (I915_LPE_PIPE_A_INTERRUPT |
> > > + I915_LPE_PIPE_B_INTERRUPT |
> > > + I915_LPE_PIPE_C_INTERRUPT))
> > > + intel_lpe_audio_irq_handler(dev_priv);
> > > +
> > > + /*
> > > * VLV_IIR is single buffered, and reflects the level
> > > * from PIPESTAT/PORT_HOTPLUG_STAT, hence clear it last.
> > > */
> > > @@ -2930,6 +2948,17 @@ static void vlv_display_irq_postinstall(struct
> > > drm_i915_private *dev_priv)
> > >
> > > WARN_ON(dev_priv->irq_mask != ~0);
> > >
> > > + if (IS_VALLEYVIEW(dev_priv) || IS_CHERRYVIEW(dev_priv)) {
> >
> > This is vlv/chv specific code, so no need to check for it.
> >
>
> OK
>
> > > + /* add interrupt masks unconditially here, the actual unmask
> > > + * will take place only if the LPE_AUDIO mode is detected
> > > + */
> > > + u32 val = (I915_LPE_PIPE_A_INTERRUPT |
> > > + I915_LPE_PIPE_B_INTERRUPT |
> > > + I915_LPE_PIPE_C_INTERRUPT);
> > > +
> > > + enable_mask |= val;
> > > + }
> > > +
> > > dev_priv->irq_mask = ~enable_mask;
> > >
> > > GEN5_IRQ_INIT(VLV_, dev_priv->irq_mask, enable_mask); diff --git
> > > a/drivers/gpu/drm/i915/i915_reg.h b/drivers/gpu/drm/i915/i915_reg.h
> > > index fcad8fa..6b16ed0 100644
> > > --- a/drivers/gpu/drm/i915/i915_reg.h
> > > +++ b/drivers/gpu/drm/i915/i915_reg.h
> > > @@ -2395,6 +2395,9 @@ enum skl_disp_power_wells {
> > > #define I915_ASLE_INTERRUPT (1<<0)
> > > #define I915_BSD_USER_INTERRUPT
> > (1<<25)
> > >
> > > +#define I915_HDMI_LPE_AUDIO_BASE (VLV_DISPLAY_BASE +
> > 0x65000)
> > > +#define I915_HDMI_LPE_AUDIO_SIZE 0x1000
> > > +
> > > #define GEN6_BSD_RNCID _MMIO(0x12198)
> > >
> > > #define GEN7_FF_THREAD_MODE _MMIO(0x20a0)
> > > diff --git a/drivers/gpu/drm/i915/intel_lpe_audio.c
> > > b/drivers/gpu/drm/i915/intel_lpe_audio.c
> > > new file mode 100644
> > > index 0000000..5335fc6
> > > --- /dev/null
> > > +++ b/drivers/gpu/drm/i915/intel_lpe_audio.c
> > > @@ -0,0 +1,369 @@
> > > +/*
> > > + * Copyright © 2016 Intel Corporation
> > > + *
> > > + * Permission is hereby granted, free of charge, to any person
> > > +obtaining a
> > > + * copy of this software and associated documentation files (the
> > > +"Software"),
> > > + * to deal in the Software without restriction, including without
> > > +limitation
> > > + * the rights to use, copy, modify, merge, publish, distribute,
> > > +sublicense,
> > > + * and/or sell copies of the Software, and to permit persons to whom
> > > +the
> > > + * Software is furnished to do so, subject to the following conditions:
> > > + *
> > > + * The above copyright notice and this permission notice (including
> > > +the next
> > > + * paragraph) shall be included in all copies or substantial portions
> > > +of the
> > > + * Software.
> > > + *
> > > + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY
> > KIND,
> > > +EXPRESS OR
> > > + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF
> > > +MERCHANTABILITY,
> > > + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN
> > NO EVENT
> > > +SHALL
> > > + * THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM,
> > DAMAGES
> > > +OR OTHER
> > > + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR
> > OTHERWISE,
> > > +ARISING
> > > + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE
> > OR
> > > +OTHER DEALINGS
> > > + * IN THE SOFTWARE.
> > > + *
> > > + * Authors:
> > > + * Pierre-Louis Bossart <pierre-louis.bossart at linux.intel.com>
> > > + * Jerome Anand <jerome.anand at intel.com>
> > > + * based on VED patches
> > > + *
> > > + */
> > > +
> > > +/**
> > > + * DOC: LPE Audio integration for HDMI or DP playback
> > > + *
> > > + * Motivation:
> > > + * Atom platforms (e.g. valleyview and cherryTrail) integrates a
> > > +DMA-based
> > > + * interface as an alternative to the traditional HDaudio path. While
> > > +this
> > > + * mode is unrelated to the LPE aka SST audio engine, the
> > > +documentation refers
> > > + * to this mode as LPE so we keep this notation for the sake of
> > consistency.
> > > + *
> > > + * The interface is handled by a separate standalone driver
> > > +maintained in the
> > > + * ALSA subsystem for simplicity. To minimize the interaction between
> > > +the two
> > > + * subsystems, a bridge is setup between the hdmi-lpe-audio and i915:
> > > + * 1. Create a platform device to share MMIO/IRQ resources
> > > + * 2. Make the platform device child of i915 device for runtime PM.
> > > + * 3. Create IRQ chip to forward the LPE audio irqs.
> > > + * the hdmi-lpe-audio driver probes the lpe audio device and creates
> > > +a new
> > > + * sound card
> > > + *
> > > + * Threats:
> > > + * Due to the restriction in Linux platform device model, user need
> > > +manually
> > > + * uninstall the hdmi-lpe-audio driver before uninstalling i915
> > > +module,
> > > + * otherwise we might run into use-after-free issues after i915
> > > +removes the
> > > + * platform device: even though hdmi-lpe-audio driver is released,
> > > +the modules
> > > + * is still in "installed" status.
> > > + *
> > > + * Implementation:
> > > + * The MMIO/REG platform resources are created according to the
> > > +registers
> > > + * specification.
> > > + * When forwarding LPE audio irqs, the flow control handler selection
> > > +depends
> > > + * on the platform, for example on valleyview handle_simple_irq is
> > enough.
> > > + *
> > > + */
> > > +
> > > +#include <linux/acpi.h>
> > > +#include <linux/device.h>
> > > +#include <linux/pci.h>
> > > +
> > > +#include "i915_drv.h"
> > > +#include <linux/delay.h>
> > > +#include <drm/intel_lpe_audio.h>
> > > +
> > > +static struct platform_device*
> > > +lpe_audio_platdev_create(struct drm_i915_private *dev_priv) {
> > > + struct drm_device *dev = &dev_priv->drm;
> > > + int ret;
> > > + struct resource rsc[2] = {};
> > > + struct platform_device *platdev;
> > > + u64 *dma_mask;
> > > + struct intel_hdmi_lpe_audio_pdata *pdata;
> > > +
> > > + if (dev_priv->lpe_audio.irq < 0)
> > > + return ERR_PTR(-EINVAL);
> > > +
> > > + platdev = platform_device_alloc("hdmi-lpe-audio", -1);
> > > + if (!platdev) {
> > > + ret = -ENOMEM;
> > > + DRM_ERROR("Failed to allocate LPE audio platform
> > device\n");
> > > + goto err;
> > > + }
> > > +
> > > + /* to work-around check_addr in nommu_map_sg() */
> > > + dma_mask = kmalloc(sizeof(*platdev->dev.dma_mask),
> > GFP_KERNEL);
> > > + if (!dma_mask) {
> > > + ret = -ENOMEM;
> > > + DRM_ERROR("Failed to allocate dma_mask\n");
> > > + goto err_put_dev;
> > > + }
> > > + *dma_mask = DMA_BIT_MASK(32);
> > > + platdev->dev.dma_mask = dma_mask;
> > > + platdev->dev.coherent_dma_mask = *dma_mask;
> > > +
> > > + rsc[0].start = rsc[0].end = dev_priv->lpe_audio.irq;
> > > + rsc[0].flags = IORESOURCE_IRQ;
> > > + rsc[0].name = "hdmi-lpe-audio-irq";
> > > +
> > > + rsc[1].start = pci_resource_start(dev->pdev, 0) +
> > > + I915_HDMI_LPE_AUDIO_BASE;
> > > + rsc[1].end = pci_resource_start(dev->pdev, 0) +
> > > + I915_HDMI_LPE_AUDIO_BASE +
> > I915_HDMI_LPE_AUDIO_SIZE - 1;
> > > + rsc[1].flags = IORESOURCE_MEM;
> > > + rsc[1].name = "hdmi-lpe-audio-mmio";
> > > +
> > > + ret = platform_device_add_resources(platdev, rsc, 2);
> > > + if (ret) {
> > > + DRM_ERROR("Failed to add resource for platform device:
> > %d\n",
> > > + ret);
> > > + goto err_put_dev;
> > > + }
> > > +
> > > + pdata = kzalloc(sizeof(*pdata), GFP_KERNEL);
> > > +
> > > + if (pdata == NULL) {
> > > + ret = -ENOMEM;
> > > + goto err_put_dev;
> > > + }
> > > + platdev->dev.platform_data = pdata;
> > > + spin_lock_init(&pdata->lpe_audio_slock);
> > > +
> > > + /* for LPE audio driver's runtime-PM */
> > > + platdev->dev.parent = dev->dev;
> > > + ret = platform_device_add(platdev);
> > > + if (ret) {
> > > + DRM_ERROR("Failed to add LPE audio platform device:
> > %d\n",
> > > + ret);
> > > + goto err_put_dev;
> > > + }
> > > +
> > > + return platdev;
> > > +err_put_dev:
> > > + platform_device_put(platdev);
> > > + kfree(dma_mask);
> > > +err:
> > > + return ERR_PTR(ret);
> > > +}
> > > +
> > > +static void lpe_audio_platdev_destroy(struct drm_i915_private
> > > +*dev_priv) {
> > > + if (!HAS_LPE_AUDIO(dev_priv))
> > > + return;
> > > + platform_device_unregister(dev_priv->lpe_audio.platdev);
> > > + kfree(dev_priv->lpe_audio.platdev->dev.dma_mask);
> > > +}
> > > +
> > > +static void lpe_audio_irq_unmask(struct irq_data *d) {
> > > + struct drm_device *dev = d->chip_data;
> > > + struct drm_i915_private *dev_priv = to_i915(dev);
> > > + unsigned long irqflags;
> > > + u32 val = (I915_LPE_PIPE_A_INTERRUPT |
> > > + I915_LPE_PIPE_B_INTERRUPT |
> > > + I915_LPE_PIPE_C_INTERRUPT);
> >
> > No pipe C on vlv.
> >
>
> OK
>
> > > +
> > > + spin_lock_irqsave(&dev_priv->irq_lock, irqflags);
> > > +
> > > + /*
> > > + * VLV_IER is already set in the vlv_display_postinstall(),
> > > + * we only change VLV_IIR and VLV_IMR
> > > + */
> > > + dev_priv->irq_mask &= ~val;
> > > + I915_WRITE(VLV_IIR, val);
> > > + I915_WRITE(VLV_IIR, val);
> > > + I915_WRITE(VLV_IMR, dev_priv->irq_mask);
> > > + POSTING_READ(VLV_IMR);
> > > +
> > > + spin_unlock_irqrestore(&dev_priv->irq_lock, irqflags); }
> > > +
> > > +static void lpe_audio_irq_mask(struct irq_data *d) {
> > > + struct drm_device *dev = d->chip_data;
> > > + struct drm_i915_private *dev_priv = to_i915(dev);
> > > + unsigned long irqflags;
> > > + u32 val = (I915_LPE_PIPE_A_INTERRUPT |
> > > + I915_LPE_PIPE_B_INTERRUPT |
> > > + I915_LPE_PIPE_C_INTERRUPT);
> >
> > ditto
> >
>
> OK
>
> > > +
> > > + spin_lock_irqsave(&dev_priv->irq_lock, irqflags);
> > > +
> > > + /*
> > > + * VLV_IER is already set in the vlv_display_postinstall(),
> > > + * we only change VLV_IIR and VLV_IMR
> > > + */
> > > + dev_priv->irq_mask |= val;
> > > + I915_WRITE(VLV_IMR, dev_priv->irq_mask);
> > > + I915_WRITE(VLV_IIR, val);
> > > + I915_WRITE(VLV_IIR, val);
> > > + POSTING_READ(VLV_IIR);
> > > +
> > > + spin_unlock_irqrestore(&dev_priv->irq_lock, irqflags); }
> > > +
> > > +static struct irq_chip lpe_audio_irqchip = {
> > > + .name = "hdmi_lpe_audio_irqchip",
> > > + .irq_mask = lpe_audio_irq_mask,
> > > + .irq_unmask = lpe_audio_irq_unmask,
> > > +};
> > > +
> > > +static int lpe_audio_irq_init(struct drm_i915_private *dev_priv) {
> > > + int irq = dev_priv->lpe_audio.irq;
> > > +
> > > + WARN_ON(!intel_irqs_enabled(dev_priv));
> > > + irq_set_chip_and_handler_name(irq,
> > > + &lpe_audio_irqchip,
> > > + handle_simple_irq,
> > > + "hdmi_lpe_audio_irq_handler");
> > > +
> > > + return irq_set_chip_data(irq, &dev_priv->drm);
> >
> > Just pass dev_priv as the chip data.
> >
>
> OK
>
> > > +}
> > > +
> > > +/**
> > > + * intel_lpe_audio_irq_handler() - forwards the LPE audio irq
> > > + * @dev_priv: the i915 drm device private data
> > > + *
> > > + * the LPE Audio irq is forwarded to the irq handler registered by
> > > +LPE audio
> > > + * driver.
> > > + */
> > > +void intel_lpe_audio_irq_handler(struct drm_i915_private *dev_priv) {
> > > + int ret;
> > > +
> > > + ret = generic_handle_irq(dev_priv->lpe_audio.irq);
> > > + if (ret)
> > > + DRM_ERROR_RATELIMITED("error handling LPE audio irq:
> > %d\n",
> > > + ret);
> > > +}
> > > +
> > > +/**
> > > + * intel_lpe_audio_detect() - check & setup lpe audio if present
> > > + * @dev_priv: the i915 drm device private data
> > > + *
> > > + * Detect if lpe audio is present
> > > + *
> > > + * Return: true if lpe audio present else Return = false */ bool
> > > +intel_lpe_audio_detect(struct drm_i915_private *dev_priv) {
> > > + int lpe_present = false;
> > > +
> > > + if (IS_VALLEYVIEW(dev_priv) || IS_CHERRYVIEW(dev_priv)) {
> >
> > Could avoid indenting the whole thig by reversing this test and doing an early
> > return.
> >
>
> Will prefer the existing method
>
> > > + static const struct pci_device_id atom_hdaudio_ids[] = {
> > > + /* Baytrail */
> > > + {PCI_DEVICE(PCI_VENDOR_ID_INTEL, 0x0f04)},
> > > + /* Braswell */
> > > + {PCI_DEVICE(PCI_VENDOR_ID_INTEL, 0x2284)},
> > > + {}
> > > + };
> >
> > IIRC I asked if we could use a HDA class match instead. But I forget what the
> > answer was. No presumably?
> >
>
> The previous reply was " we are not aware of any such class that exists at present"
Hmm. 0x0403 would be audio device. I guess we can't really use that
unless we combine it with the devfn (assuming the hda controller is
alwauys device 3. So yeah, specific device IDs seem better.
>
> > > +
> > > + if (!pci_dev_present(atom_hdaudio_ids)) {
> > > + DRM_INFO("%s%s\n", "HDaudio controller not
> > detected,",
> > > + "using LPE audio instead\n");
> > > + lpe_present = true;
> > > + }
> > > + }
> > > + return lpe_present;
> > > +}
> > > +
> > > +/**
> > > + * intel_lpe_audio_setup() - setup the bridge between HDMI LPE Audio
> > > + * driver and i915
> > > + * @dev_priv: the i915 drm device private data
> > > + *
> > > + * set up the minimum required resources for the bridge: irq chip,
> > > + * platform resource and platform device. i915 device is set as
> > > +parent
> > > + * of the new platform device.
> > > + *
> > > + * Return: 0 if successful. non-zero if allocation/initialization
> > > +fails */ int intel_lpe_audio_setup(struct drm_i915_private
> > > +*dev_priv) {
> > > + int ret;
> > > +
> > > + dev_priv->lpe_audio.irq = irq_alloc_desc(0);
> > > + if (dev_priv->lpe_audio.irq < 0) {
> > > + DRM_ERROR("Failed to allocate IRQ desc: %d\n",
> > > + dev_priv->lpe_audio.irq);
> > > + ret = dev_priv->lpe_audio.irq;
> > > + goto err;
> > > + }
> > > +
> > > + DRM_DEBUG("irq = %d\n", dev_priv->lpe_audio.irq);
> > > +
> > > + ret = lpe_audio_irq_init(dev_priv);
> > > +
> > > + if (ret) {
> > > + DRM_ERROR("Failed to initialize irqchip for lpe audio: %d\n",
> > > + ret);
> > > + goto err_free_irq;
> > > + }
> > > +
> > > + dev_priv->lpe_audio.platdev = lpe_audio_platdev_create(dev_priv);
> > > +
> > > + if (IS_ERR(dev_priv->lpe_audio.platdev)) {
> > > + ret = PTR_ERR(dev_priv->lpe_audio.platdev);
> > > + DRM_ERROR("Failed to create lpe audio platform device:
> > %d\n",
> > > + ret);
> > > + goto err_free_irq;
> > > + }
> > > +
> > > + return 0;
> > > +err_free_irq:
> > > + irq_free_desc(dev_priv->lpe_audio.irq);
> > > +err:
> > > + dev_priv->lpe_audio.irq = -1;
> > > + dev_priv->lpe_audio.platdev = NULL;
> > > + return ret;
> > > +}
> > > +
> > > +
> > > +/**
> > > + * intel_lpe_audio_init() - detect and setup the bridge between HDMI
> > > +LPE Audio
> > > + * driver and i915
> > > + * @dev_priv: the i915 drm device private data
> > > + *
> > > + * Return: 0 if successful. non-zero if detection or
> > > + * llocation/initialization fails
> > > + */
> > > +int intel_lpe_audio_init(struct drm_i915_private *dev_priv) {
> > > + int ret = -ENODEV;
> > > +
> > > + if (intel_lpe_audio_detect(dev_priv)) {
> > > + ret = intel_lpe_audio_setup(dev_priv);
> > > + if (ret < 0)
> > > + DRM_ERROR("failed to setup LPE Audio bridge\n");
> > > + }
> > > + return ret;
> > > +}
> > > +
> > > +/**
> > > + * intel_lpe_audio_teardown() - destroy the bridge between HDMI LPE
> > > + * audio driver and i915
> > > + * @dev_priv: the i915 drm device private data
> > > + *
> > > + * release all the resources for LPE audio <-> i915 bridge.
> > > + */
> > > +void intel_lpe_audio_teardown(struct drm_i915_private *dev_priv) {
> > > + unsigned long irqflags;
> > > + struct irq_desc *desc;
> > > +
> > > + desc = (dev_priv->lpe_audio.irq >= 0) ?
> > > + irq_to_desc(dev_priv->lpe_audio.irq) : NULL;
> >
> > Why not just "if (lpe not initialized) return;" ?
> >
>
> Need to perform cleaning in spite of it
Why? Partial initialization doesn't sounds good.
>
> > > +
> > > + /**
> > > + * mask LPE audio irq before destroying
> > > + */
> > > + if (desc)
> > > + lpe_audio_irq_mask(&desc->irq_data);
> >
> > This seems racy. Should unregister the platdev first I think,
> >
>
> OK
>
> > > +
> > > + spin_lock_irqsave(&dev_priv->irq_lock, irqflags);
> > > +
> > > + lpe_audio_platdev_destroy(dev_priv);
> > > +
> > > + if (desc)
> > > + irq_free_desc(dev_priv->lpe_audio.irq);
> > > +
> > > + spin_unlock_irqrestore(&dev_priv->irq_lock, irqflags); }
> > > diff --git a/include/drm/intel_lpe_audio.h
> > > b/include/drm/intel_lpe_audio.h new file mode 100644 index
> > > 0000000..a64c449
> > > --- /dev/null
> > > +++ b/include/drm/intel_lpe_audio.h
> > > @@ -0,0 +1,45 @@
> > > +/*
> > > + * Copyright © 2016 Intel Corporation
> > > + *
> > > + * Permission is hereby granted, free of charge, to any person
> > > +obtaining a
> > > + * copy of this software and associated documentation files (the
> > > +"Software"),
> > > + * to deal in the Software without restriction, including without
> > > +limitation
> > > + * the rights to use, copy, modify, merge, publish, distribute,
> > > +sublicense,
> > > + * and/or sell copies of the Software, and to permit persons to whom
> > > +the
> > > + * Software is furnished to do so, subject to the following conditions:
> > > + *
> > > + * The above copyright notice and this permission notice (including
> > > +the next
> > > + * paragraph) shall be included in all copies or substantial portions
> > > +of the
> > > + * Software.
> > > + *
> > > + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY
> > KIND,
> > > +EXPRESS OR
> > > + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF
> > > +MERCHANTABILITY,
> > > + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN
> > NO EVENT
> > > +SHALL
> > > + * THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM,
> > DAMAGES
> > > +OR OTHER
> > > + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR
> > OTHERWISE,
> > > +ARISING
> > > + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE
> > OR
> > > +OTHER DEALINGS
> > > + * IN THE SOFTWARE.
> > > + */
> > > +
> > > +#ifndef _INTEL_LPE_AUDIO_H_
> > > +#define _INTEL_LPE_AUDIO_H_
> > > +
> > > +#include <linux/types.h>
> > > +
> > > +#define HDMI_MAX_ELD_BYTES 128
> > > +
> > > +struct intel_hdmi_lpe_audio_eld {
> > > + int port_id;
> > > + unsigned char eld_data[HDMI_MAX_ELD_BYTES]; };
> > > +
> > > +struct intel_hdmi_lpe_audio_pdata {
> > > + bool notify_pending;
> > > + int tmds_clock_speed;
> > > + bool hdmi_connected;
> > > + struct intel_hdmi_lpe_audio_eld eld;
> > > + void (*notify_audio_lpe)(void *audio_ptr);
> > > + spinlock_t lpe_audio_slock;
> > > +};
> > > +
> > > +#endif /* _I915_LPE_AUDIO_H_ */
> > > --
> > > 2.9.3
> >
> > --
> > Ville Syrjälä
> > Intel OTC
--
Ville Syrjälä
Intel OTC
More information about the Intel-gfx
mailing list