[Intel-gfx] [PATCH 9/9] drm/i915: Add render decompression support
Ville Syrjälä
ville.syrjala at linux.intel.com
Thu Jan 5 15:12:59 UTC 2017
On Wed, Jan 04, 2017 at 05:14:04PM -0200, Paulo Zanoni wrote:
> Em Qua, 2017-01-04 às 20:42 +0200, ville.syrjala at linux.intel.com
> escreveu:
> > From: Ville Syrjälä <ville.syrjala at linux.intel.com>
> >
> > SKL+ display engine can scan out certain kinds of compressed surfaces
> > produced by the render engine. This involved telling the display
> > engine
> > the location of the color control surfae (CCS) which describes
> > which parts of the main surface are compressed and which are not. The
> > location of CCS is provided by userspace as just another plane with
> > its
> > own offset.
> >
> > Add the required stuff to validate the user provided AUX plane
> > metadata
> > and convert the user provided linear offset into something the
> > hardware
> > can consume.
> >
> > Due to hardware limitations we require that the main surface and
> > the AUX surface (CCS) be part of the same bo. The hardware also
> > makes life hard by not allowing you to provide separate x/y offsets
> > for the main and AUX surfaces (excpet with NV12), so finding suitable
> > offsets for both requires a bit of work. Assuming we still want keep
> > playing tricks with the offsets. I've just gone with a dumb "search
> > backward for suitable offsets" approach, which is far from optimal,
> > but it works.
> >
> > Also not all planes will be capable of scanning out compressed
> > surfaces,
> > and eg. 90/270 degree rotation is not supported in combination with
> > decompression either.
> >
> > This patch may contain work from at least the following people:
> > * Vandana Kannan <vandana.kannan at intel.com>
> > * Daniel Vetter <daniel at ffwll.ch>
> > * Ben Widawsky <ben at bwidawsk.net>
>
> As I mentioned to Ben in the other email, there are some points of
> BSpec that say "if render decompression is enabled, to this", which we
> largely ignored so far. I hope they are all marked as workarounds. From
> a quick look, it looks like we need at least Display WAs #0390, #0531
> and #1125, and maybe some other non-display WAs (please take a look at
> the BSpec list). I'll assume they were not implemented yet since I
> don't see WA comments on the patches. I think we need them, otherwise
> we may introduce more SKL flickering problems.
I went through the list and those three do seem like the likely things
we want. I'll post a revised patch with those included.
>
> Thanks,
> Paulo
>
> >
> > Cc: Vandana Kannan <vandana.kannan at intel.com>
> > Cc: Daniel Vetter <daniel at ffwll.ch>
> > Cc: Ben Widawsky <ben at bwidawsk.net>
> > Cc: Jason Ekstrand <jason at jlekstrand.net>
> > Signed-off-by: Ville Syrjälä <ville.syrjala at linux.intel.com>
> > ---
> > drivers/gpu/drm/i915/i915_reg.h | 22 ++++
> > drivers/gpu/drm/i915/intel_display.c | 219
> > +++++++++++++++++++++++++++++++++--
> > drivers/gpu/drm/i915/intel_pm.c | 8 +-
> > drivers/gpu/drm/i915/intel_sprite.c | 5 +
> > 4 files changed, 240 insertions(+), 14 deletions(-)
> >
> > diff --git a/drivers/gpu/drm/i915/i915_reg.h
> > b/drivers/gpu/drm/i915/i915_reg.h
> > index 00970aa77afa..05e18e742776 100644
> > --- a/drivers/gpu/drm/i915/i915_reg.h
> > +++ b/drivers/gpu/drm/i915/i915_reg.h
> > @@ -6209,6 +6209,28 @@ enum {
> > _ID(id, _PS_ECC_STAT_1A,
> > _PS_ECC_STAT_2A), \
> > _ID(id, _PS_ECC_STAT_1B, _PS_ECC_STAT_2B))
> >
> > +#define PLANE_AUX_DIST_1_A 0x701c0
> > +#define PLANE_AUX_DIST_2_A 0x702c0
> > +#define PLANE_AUX_DIST_1_B 0x711c0
> > +#define PLANE_AUX_DIST_2_B 0x712c0
> > +#define _PLANE_AUX_DIST_1(pipe) \
> > + _PIPE(pipe, PLANE_AUX_DIST_1_A,
> > PLANE_AUX_DIST_1_B)
> > +#define _PLANE_AUX_DIST_2(pipe) \
> > + _PIPE(pipe, PLANE_AUX_DIST_2_A,
> > PLANE_AUX_DIST_2_B)
> > +#define PLANE_AUX_DIST(pipe, plane) \
> > + _MMIO_PLANE(plane, _PLANE_AUX_DIST_1(pipe),
> > _PLANE_AUX_DIST_2(pipe))
> > +
> > +#define PLANE_AUX_OFFSET_1_A 0x701c4
> > +#define PLANE_AUX_OFFSET_2_A 0x702c4
> > +#define PLANE_AUX_OFFSET_1_B 0x711c4
> > +#define PLANE_AUX_OFFSET_2_B 0x712c4
> > +#define _PLANE_AUX_OFFSET_1(pipe) \
> > + _PIPE(pipe, PLANE_AUX_OFFSET_1_A,
> > PLANE_AUX_OFFSET_1_B)
> > +#define _PLANE_AUX_OFFSET_2(pipe) \
> > + _PIPE(pipe, PLANE_AUX_OFFSET_2_A,
> > PLANE_AUX_OFFSET_2_B)
> > +#define PLANE_AUX_OFFSET(pipe, plane) \
> > + _MMIO_PLANE(plane, _PLANE_AUX_OFFSET_1(pipe),
> > _PLANE_AUX_OFFSET_2(pipe))
> > +
> > /* legacy palette */
> > #define _LGC_PALETTE_A 0x4a000
> > #define _LGC_PALETTE_B 0x4a800
> > diff --git a/drivers/gpu/drm/i915/intel_display.c
> > b/drivers/gpu/drm/i915/intel_display.c
> > index 38de9df0ec60..b547332eeda1 100644
> > --- a/drivers/gpu/drm/i915/intel_display.c
> > +++ b/drivers/gpu/drm/i915/intel_display.c
> > @@ -2064,11 +2064,19 @@ intel_tile_width_bytes(const struct
> > drm_framebuffer *fb, int plane)
> > return 128;
> > else
> > return 512;
> > + case I915_FORMAT_MOD_Y_TILED_CCS:
> > + if (plane == 1)
> > + return 64;
> > + /* fall through */
> > case I915_FORMAT_MOD_Y_TILED:
> > if (IS_GEN2(dev_priv) ||
> > HAS_128_BYTE_Y_TILING(dev_priv))
> > return 128;
> > else
> > return 512;
> > + case I915_FORMAT_MOD_Yf_TILED_CCS:
> > + if (plane == 1)
> > + return 64;
> > + /* fall through */
> > case I915_FORMAT_MOD_Yf_TILED:
> > /*
> > * Bspec seems to suggest that the Yf tile width
> > would
> > @@ -2156,7 +2164,7 @@ static unsigned int intel_surf_alignment(const
> > struct drm_framebuffer *fb,
> > struct drm_i915_private *dev_priv = to_i915(fb->dev);
> >
> > /* AUX_DIST needs only 4K alignment */
> > - if (fb->format->format == DRM_FORMAT_NV12 && plane == 1)
> > + if (plane == 1)
> > return 4096;
> >
> > switch (fb->modifier) {
> > @@ -2166,6 +2174,8 @@ static unsigned int intel_surf_alignment(const
> > struct drm_framebuffer *fb,
> > if (INTEL_GEN(dev_priv) >= 9)
> > return 256 * 1024;
> > return 0;
> > + case I915_FORMAT_MOD_Y_TILED_CCS:
> > + case I915_FORMAT_MOD_Yf_TILED_CCS:
> > case I915_FORMAT_MOD_Y_TILED:
> > case I915_FORMAT_MOD_Yf_TILED:
> > return 1 * 1024 * 1024;
> > @@ -2472,6 +2482,7 @@ static unsigned int
> > intel_fb_modifier_to_tiling(uint64_t fb_modifier)
> > case I915_FORMAT_MOD_X_TILED:
> > return I915_TILING_X;
> > case I915_FORMAT_MOD_Y_TILED:
> > + case I915_FORMAT_MOD_Y_TILED_CCS:
> > return I915_TILING_Y;
> > default:
> > return I915_TILING_NONE;
> > @@ -2536,6 +2547,35 @@ intel_fill_fb_info(struct drm_i915_private
> > *dev_priv,
> >
> > intel_fb_offset_to_xy(&x, &y, fb, i);
> >
> > + if ((fb->modifier == I915_FORMAT_MOD_Y_TILED_CCS ||
> > + fb->modifier == I915_FORMAT_MOD_Yf_TILED_CCS)
> > && i == 1) {
> > + int main_x, main_y;
> > + int ccs_x, ccs_y;
> > +
> > + /*
> > + * Each byte of CCS corresponds to a 16x8
> > area of the main surface, and
> > + * each CCS tile is 64x64 bytes.
> > + */
> > + ccs_x = (x * 16) % (64 * 16);
> > + ccs_y = (y * 8) % (64 * 8);
> > + main_x = intel_fb->normal[0].x % (64 * 16);
> > + main_y = intel_fb->normal[0].y % (64 * 8);
> > +
> > + /*
> > + * CCS doesn't have its own x/y offset
> > register, so the intra CCS tile
> > + * x/y offsets must match between CCS and
> > the main surface.
> > + */
> > + if (main_x != ccs_x || main_y != ccs_y) {
> > + DRM_DEBUG_KMS("Bad CCS x/y (main
> > %d,%d ccs %d,%d) full (main %d,%d ccs %d,%d)\n",
> > + main_x, main_y,
> > + ccs_x, ccs_y,
> > + intel_fb->normal[0].x,
> > + intel_fb->normal[0].y,
> > + x, y);
> > + return -EINVAL;
> > + }
> > + }
> > +
> > /*
> > * The fence (if used) is aligned to the start of
> > the object
> > * so having the framebuffer wrap around across the
> > edge of the
> > @@ -2873,6 +2913,9 @@ static int skl_max_plane_width(const struct
> > drm_framebuffer *fb, int plane,
> > break;
> > }
> > break;
> > + case I915_FORMAT_MOD_Y_TILED_CCS:
> > + case I915_FORMAT_MOD_Yf_TILED_CCS:
> > + /* FIXME AUX plane? */
> > case I915_FORMAT_MOD_Y_TILED:
> > case I915_FORMAT_MOD_Yf_TILED:
> > switch (cpp) {
> > @@ -2895,6 +2938,42 @@ static int skl_max_plane_width(const struct
> > drm_framebuffer *fb, int plane,
> > return 2048;
> > }
> >
> > +static bool skl_check_main_ccs_coordinates(struct intel_plane_state
> > *plane_state,
> > + int main_x, int main_y,
> > u32 main_offset)
> > +{
> > + const struct drm_framebuffer *fb = plane_state->base.fb;
> > + int aux_x = plane_state->aux.x;
> > + int aux_y = plane_state->aux.y;
> > + u32 aux_offset = plane_state->aux.offset;
> > + u32 alignment = intel_surf_alignment(fb, 1);
> > +
> > + while (aux_offset >= main_offset && aux_y <= main_y) {
> > + int x, y;
> > +
> > + if (aux_x == main_x && aux_y == main_y)
> > + break;
> > +
> > + if (aux_offset == 0)
> > + break;
> > +
> > + x = aux_x / 16;
> > + y = aux_y / 8;
> > + aux_offset = intel_adjust_tile_offset(&x, &y,
> > plane_state, 1,
> > + aux_offset,
> > aux_offset - alignment);
> > + aux_x = x * 16 + aux_x % 16;
> > + aux_y = y * 8 + aux_y % 8;
> > + }
> > +
> > + if (aux_x != main_x || aux_y != main_y)
> > + return false;
> > +
> > + plane_state->aux.offset = aux_offset;
> > + plane_state->aux.x = aux_x;
> > + plane_state->aux.y = aux_y;
> > +
> > + return true;
> > +}
> > +
> > static int skl_check_main_surface(struct intel_plane_state
> > *plane_state)
> > {
> > const struct drm_framebuffer *fb = plane_state->base.fb;
> > @@ -2937,7 +3016,7 @@ static int skl_check_main_surface(struct
> > intel_plane_state *plane_state)
> >
> > while ((x + w) * cpp > fb->pitches[0]) {
> > if (offset == 0) {
> > - DRM_DEBUG_KMS("Unable to find
> > suitable display surface offset\n");
> > + DRM_DEBUG_KMS("Unable to find
> > suitable display surface offset due to X-tiling\n");
> > return -EINVAL;
> > }
> >
> > @@ -2946,6 +3025,26 @@ static int skl_check_main_surface(struct
> > intel_plane_state *plane_state)
> > }
> > }
> >
> > + /*
> > + * CCS AUX surface doesn't have its own x/y offsets, we must
> > make sure
> > + * they match with the main surface x/y offsets.
> > + */
> > + if (fb->modifier == I915_FORMAT_MOD_Y_TILED_CCS ||
> > + fb->modifier == I915_FORMAT_MOD_Yf_TILED_CCS) {
> > + while (!skl_check_main_ccs_coordinates(plane_state,
> > x, y, offset)) {
> > + if (offset == 0)
> > + break;
> > +
> > + offset = intel_adjust_tile_offset(&x, &y,
> > plane_state, 0,
> > + offset,
> > offset - alignment);
> > + }
> > +
> > + if (x != plane_state->aux.x || y != plane_state-
> > >aux.y) {
> > + DRM_DEBUG_KMS("Unable to find suitable
> > display surface offset due to CCS\n");
> > + return -EINVAL;
> > + }
> > + }
> > +
> > plane_state->main.offset = offset;
> > plane_state->main.x = x;
> > plane_state->main.y = y;
> > @@ -2982,6 +3081,53 @@ static int skl_check_nv12_aux_surface(struct
> > intel_plane_state *plane_state)
> > return 0;
> > }
> >
> > +static int skl_check_ccs_aux_surface(struct intel_plane_state
> > *plane_state)
> > +{
> > + struct intel_plane *plane = to_intel_plane(plane_state-
> > >base.plane);
> > + struct intel_crtc *crtc = to_intel_crtc(plane_state-
> > >base.crtc);
> > + int src_x = plane_state->base.src.x1 >> 16;
> > + int src_y = plane_state->base.src.y1 >> 16;
> > + int x = src_x / 16;
> > + int y = src_y / 8;
> > + u32 offset;
> > +
> > + switch (plane->id) {
> > + case PLANE_PRIMARY:
> > + case PLANE_SPRITE0:
> > + break;
> > + default:
> > + DRM_DEBUG_KMS("RC support only on plane 1 and 2\n");
> > + return -EINVAL;
> > + }
> > +
> > + if (crtc->pipe == PIPE_C) {
> > + DRM_DEBUG_KMS("No RC support on pipe C\n");
> > + return -EINVAL;
> > + }
> > + /*
> > + * TODO:
> > + * 1. Disable stereo 3D when render decomp is enabled (bit
> > 7:6)
> > + * 2. Render decompression must not be used in VTd pass-
> > through mode
> > + * 3. Program hashing select CHICKEN_MISC1 bit 15
> > + */
> > +
> > + if (plane_state->base.rotation &&
> > + plane_state->base.rotation & ~(DRM_ROTATE_0 |
> > DRM_ROTATE_180)) {
> > + DRM_DEBUG_KMS("RC support only with 0/180 degree
> > rotation %x\n",
> > + plane_state->base.rotation);
> > + return -EINVAL;
> > + }
> > +
> > + intel_add_fb_offsets(&x, &y, plane_state, 1);
> > + offset = intel_compute_tile_offset(&x, &y, plane_state, 1);
> > +
> > + plane_state->aux.offset = offset;
> > + plane_state->aux.x = x * 16 + src_x % 16;
> > + plane_state->aux.y = y * 8 + src_y % 8;
> > +
> > + return 0;
> > +}
> > +
> > int skl_check_plane_surface(struct intel_plane_state *plane_state)
> > {
> > const struct drm_framebuffer *fb = plane_state->base.fb;
> > @@ -3002,6 +3148,11 @@ int skl_check_plane_surface(struct
> > intel_plane_state *plane_state)
> > ret = skl_check_nv12_aux_surface(plane_state);
> > if (ret)
> > return ret;
> > + } else if (fb->modifier == I915_FORMAT_MOD_Y_TILED_CCS ||
> > + fb->modifier == I915_FORMAT_MOD_Yf_TILED_CCS) {
> > + ret = skl_check_ccs_aux_surface(plane_state);
> > + if (ret)
> > + return ret;
> > } else {
> > plane_state->aux.offset = ~0xfff;
> > plane_state->aux.x = 0;
> > @@ -3357,8 +3508,12 @@ u32 skl_plane_ctl_tiling(uint64_t fb_modifier)
> > return PLANE_CTL_TILED_X;
> > case I915_FORMAT_MOD_Y_TILED:
> > return PLANE_CTL_TILED_Y;
> > + case I915_FORMAT_MOD_Y_TILED_CCS:
> > + return PLANE_CTL_TILED_Y |
> > PLANE_CTL_DECOMPRESSION_ENABLE;
> > case I915_FORMAT_MOD_Yf_TILED:
> > return PLANE_CTL_TILED_YF;
> > + case I915_FORMAT_MOD_Yf_TILED_CCS:
> > + return PLANE_CTL_TILED_YF |
> > PLANE_CTL_DECOMPRESSION_ENABLE;
> > default:
> > MISSING_CASE(fb_modifier);
> > }
> > @@ -3401,6 +3556,7 @@ static void skylake_update_primary_plane(struct
> > drm_plane *plane,
> > u32 plane_ctl;
> > unsigned int rotation = plane_state->base.rotation;
> > u32 stride = skl_plane_stride(fb, 0, rotation);
> > + u32 aux_stride = skl_plane_stride(fb, 1, rotation);
> > u32 surf_addr = plane_state->main.offset;
> > int scaler_id = plane_state->scaler_id;
> > int src_x = plane_state->main.x;
> > @@ -3436,6 +3592,10 @@ static void
> > skylake_update_primary_plane(struct drm_plane *plane,
> > I915_WRITE(PLANE_OFFSET(pipe, plane_id), (src_y << 16) |
> > src_x);
> > I915_WRITE(PLANE_STRIDE(pipe, plane_id), stride);
> > I915_WRITE(PLANE_SIZE(pipe, plane_id), (src_h << 16) |
> > src_w);
> > + I915_WRITE(PLANE_AUX_DIST(pipe, plane_id),
> > + (plane_state->aux.offset - surf_addr) |
> > aux_stride);
> > + I915_WRITE(PLANE_AUX_OFFSET(pipe, plane_id),
> > + (plane_state->aux.y << 16) | plane_state->aux.x);
> >
> > if (scaler_id >= 0) {
> > uint32_t ps_ctrl = 0;
> > @@ -9807,10 +9967,16 @@ skylake_get_initial_plane_config(struct
> > intel_crtc *crtc,
> > fb->modifier = I915_FORMAT_MOD_X_TILED;
> > break;
> > case PLANE_CTL_TILED_Y:
> > - fb->modifier = I915_FORMAT_MOD_Y_TILED;
> > + if (val & PLANE_CTL_DECOMPRESSION_ENABLE)
> > + fb->modifier = I915_FORMAT_MOD_Y_TILED_CCS;
> > + else
> > + fb->modifier = I915_FORMAT_MOD_Y_TILED;
> > break;
> > case PLANE_CTL_TILED_YF:
> > - fb->modifier = I915_FORMAT_MOD_Yf_TILED;
> > + if (val & PLANE_CTL_DECOMPRESSION_ENABLE)
> > + fb->modifier = I915_FORMAT_MOD_Yf_TILED_CCS;
> > + else
> > + fb->modifier = I915_FORMAT_MOD_Yf_TILED;
> > break;
> > default:
> > MISSING_CASE(tiling);
> > @@ -12014,7 +12180,7 @@ static void skl_do_mmio_flip(struct
> > intel_crtc *intel_crtc,
> > u32 ctl, stride = skl_plane_stride(fb, 0, rotation);
> >
> > ctl = I915_READ(PLANE_CTL(pipe, 0));
> > - ctl &= ~PLANE_CTL_TILED_MASK;
> > + ctl &= ~(PLANE_CTL_TILED_MASK |
> > PLANE_CTL_DECOMPRESSION_ENABLE);
> > switch (fb->modifier) {
> > case DRM_FORMAT_MOD_NONE:
> > break;
> > @@ -12024,9 +12190,15 @@ static void skl_do_mmio_flip(struct
> > intel_crtc *intel_crtc,
> > case I915_FORMAT_MOD_Y_TILED:
> > ctl |= PLANE_CTL_TILED_Y;
> > break;
> > + case I915_FORMAT_MOD_Y_TILED_CCS:
> > + ctl |= PLANE_CTL_TILED_Y |
> > PLANE_CTL_DECOMPRESSION_ENABLE;
> > + break;
> > case I915_FORMAT_MOD_Yf_TILED:
> > ctl |= PLANE_CTL_TILED_YF;
> > break;
> > + case I915_FORMAT_MOD_Yf_TILED_CCS:
> > + ctl |= PLANE_CTL_TILED_YF |
> > PLANE_CTL_DECOMPRESSION_ENABLE;
> > + break;
> > default:
> > MISSING_CASE(fb->modifier);
> > }
> > @@ -15926,8 +16098,8 @@ static int intel_framebuffer_init(struct
> > drm_device *dev,
> > {
> > struct drm_i915_private *dev_priv = to_i915(dev);
> > unsigned int tiling = i915_gem_object_get_tiling(obj);
> > - int ret;
> > - u32 pitch_limit, stride_alignment;
> > + int ret, i;
> > + u32 pitch_limit;
> > struct drm_format_name_buf format_name;
> >
> > WARN_ON(!mutex_is_locked(&dev->struct_mutex));
> > @@ -15953,6 +16125,19 @@ static int intel_framebuffer_init(struct
> > drm_device *dev,
> >
> > /* Passed in modifier sanity checking. */
> > switch (mode_cmd->modifier[0]) {
> > + case I915_FORMAT_MOD_Y_TILED_CCS:
> > + case I915_FORMAT_MOD_Yf_TILED_CCS:
> > + switch (mode_cmd->pixel_format) {
> > + case DRM_FORMAT_XBGR8888:
> > + case DRM_FORMAT_ABGR8888:
> > + case DRM_FORMAT_XRGB8888:
> > + case DRM_FORMAT_ARGB8888:
> > + break;
> > + default:
> > + DRM_DEBUG_KMS("RC supported only with
> > RGB8888 formats\n");
> > + return -EINVAL;
> > + }
> > + /* fall through */
> > case I915_FORMAT_MOD_Y_TILED:
> > case I915_FORMAT_MOD_Yf_TILED:
> > if (INTEL_GEN(dev_priv) < 9) {
> > @@ -16061,11 +16246,21 @@ static int intel_framebuffer_init(struct
> > drm_device *dev,
> >
> > drm_helper_mode_fill_fb_struct(dev, &intel_fb->base,
> > mode_cmd);
> >
> > - stride_alignment = intel_fb_stride_alignment(&intel_fb-
> > >base, 0);
> > - if (mode_cmd->pitches[0] & (stride_alignment - 1)) {
> > - DRM_DEBUG_KMS("pitch (%d) must be at least %u byte
> > aligned\n",
> > - mode_cmd->pitches[0],
> > stride_alignment);
> > - return -EINVAL;
> > + for (i = 0; i < intel_fb->base.format->num_planes; i++) {
> > + u32 stride_alignment;
> > +
> > + if (mode_cmd->handles[i] != mode_cmd->handles[0]) {
> > + DRM_DEBUG_KMS("bad plane %d handle\n", i);
> > + return -EINVAL;
> > + }
> > +
> > + stride_alignment =
> > intel_fb_stride_alignment(&intel_fb->base, i);
> > +
> > + if (mode_cmd->pitches[i] & (stride_alignment - 1)) {
> > + DRM_DEBUG_KMS("plane %d pitch (%d) must be
> > at least %u byte aligned\n",
> > + i, mode_cmd->pitches[i],
> > stride_alignment);
> > + return -EINVAL;
> > + }
> > }
> >
> > intel_fb->obj = obj;
> > diff --git a/drivers/gpu/drm/i915/intel_pm.c
> > b/drivers/gpu/drm/i915/intel_pm.c
> > index 249623d45be0..add359022c96 100644
> > --- a/drivers/gpu/drm/i915/intel_pm.c
> > +++ b/drivers/gpu/drm/i915/intel_pm.c
> > @@ -3314,7 +3314,9 @@ skl_ddb_min_alloc(const struct drm_plane_state
> > *pstate,
> >
> > /* For Non Y-tile return 8-blocks */
> > if (fb->modifier != I915_FORMAT_MOD_Y_TILED &&
> > - fb->modifier != I915_FORMAT_MOD_Yf_TILED)
> > + fb->modifier != I915_FORMAT_MOD_Yf_TILED &&
> > + fb->modifier != I915_FORMAT_MOD_Y_TILED_CCS &&
> > + fb->modifier != I915_FORMAT_MOD_Yf_TILED_CCS)
> > return 8;
> >
> > src_w = drm_rect_width(&intel_pstate->base.src) >> 16;
> > @@ -3590,7 +3592,9 @@ static int skl_compute_plane_wm(const struct
> > drm_i915_private *dev_priv,
> > }
> >
> > y_tiled = fb->modifier == I915_FORMAT_MOD_Y_TILED ||
> > - fb->modifier == I915_FORMAT_MOD_Yf_TILED;
> > + fb->modifier == I915_FORMAT_MOD_Yf_TILED ||
> > + fb->modifier == I915_FORMAT_MOD_Y_TILED_CCS ||
> > + fb->modifier == I915_FORMAT_MOD_Yf_TILED_CCS;
> > x_tiled = fb->modifier == I915_FORMAT_MOD_X_TILED;
> >
> > /* Display WA #1141: kbl. */
> > diff --git a/drivers/gpu/drm/i915/intel_sprite.c
> > b/drivers/gpu/drm/i915/intel_sprite.c
> > index 7031bc733d97..063a994815d0 100644
> > --- a/drivers/gpu/drm/i915/intel_sprite.c
> > +++ b/drivers/gpu/drm/i915/intel_sprite.c
> > @@ -210,6 +210,7 @@ skl_update_plane(struct drm_plane *drm_plane,
> > u32 surf_addr = plane_state->main.offset;
> > unsigned int rotation = plane_state->base.rotation;
> > u32 stride = skl_plane_stride(fb, 0, rotation);
> > + u32 aux_stride = skl_plane_stride(fb, 1, rotation);
> > int crtc_x = plane_state->base.dst.x1;
> > int crtc_y = plane_state->base.dst.y1;
> > uint32_t crtc_w = drm_rect_width(&plane_state->base.dst);
> > @@ -248,6 +249,10 @@ skl_update_plane(struct drm_plane *drm_plane,
> > I915_WRITE(PLANE_OFFSET(pipe, plane_id), (y << 16) | x);
> > I915_WRITE(PLANE_STRIDE(pipe, plane_id), stride);
> > I915_WRITE(PLANE_SIZE(pipe, plane_id), (src_h << 16) |
> > src_w);
> > + I915_WRITE(PLANE_AUX_DIST(pipe, plane_id),
> > + (plane_state->aux.offset - surf_addr) |
> > aux_stride);
> > + I915_WRITE(PLANE_AUX_OFFSET(pipe, plane_id),
> > + (plane_state->aux.y << 16) | plane_state->aux.x);
> >
> > /* program plane scaler */
> > if (plane_state->scaler_id >= 0) {
--
Ville Syrjälä
Intel OTC
More information about the Intel-gfx
mailing list