[Intel-gfx] [PATCH] drm/i915: Add MIPI_IO WA and program DSI regulators

[Mika Kahola]

On Thu, 2017-01-19 at 11:41 +0530, Vidya Srinivas wrote:
> From: Uma Shankar <uma.shankar at intel.com>
> 
> Enable MIPI IO WA for BXT DSI as per bspec and
> program the DSI regulators.
> 
> v2: Moved IO enable to pre-enable as per Mika's
> review comments. Also reused the existing register
> definition for BXT_P_CR_GT_DISP_PWRON.
> 
> v3: Added Programming the DSI regulators as per disable/enable
> sequences.
> 
> Signed-off-by: Uma Shankar <uma.shankar at intel.com>
> ---
>  drivers/gpu/drm/i915/i915_reg.h  |  7 +++++++
>  drivers/gpu/drm/i915/intel_dsi.c | 21 +++++++++++++++++++++
>  2 files changed, 28 insertions(+)
> 
> diff --git a/drivers/gpu/drm/i915/i915_reg.h
> b/drivers/gpu/drm/i915/i915_reg.h
> index 00970aa..0a9ad44 100644
> --- a/drivers/gpu/drm/i915/i915_reg.h
> +++ b/drivers/gpu/drm/i915/i915_reg.h
> @@ -1553,6 +1553,7 @@ enum skl_disp_power_wells {
>  	_MMIO(_BXT_PHY_CH(phy, ch, reg_ch0, reg_ch1))
>  
>  #define BXT_P_CR_GT_DISP_PWRON		_MMIO(0x138090)
> +#define  MIPIO_RST_CTRL				(1 << 2)
>  
>  #define _BXT_PHY_CTL_DDI_A		0x64C00
>  #define _BXT_PHY_CTL_DDI_B		0x64C10
> @@ -8301,6 +8302,12 @@ enum {
>  #define _BXT_MIPIC_PORT_CTRL				0x6B8C0
>  #define BXT_MIPI_PORT_CTRL(tc)	_MMIO_MIPI(tc,
> _BXT_MIPIA_PORT_CTRL, _BXT_MIPIC_PORT_CTRL)
>  
> +#define BXT_P_DSI_REGULATOR_CFG			_MMIO(0x16002
> 0)
> +#define  STAP_SELECT					(1 << 0)
> +
> +#define BXT_P_DSI_REGULATOR_TX_CTRL		_MMIO(0x160054)
> +#define  HS_IO_CTRL_SELECT				(1 << 0)
> +
>  #define  DPI_ENABLE					(1 << 31)
> /* A + C */
>  #define  MIPIA_MIPI4DPHY_DELAY_COUNT_SHIFT		27
>  #define  MIPIA_MIPI4DPHY_DELAY_COUNT_MASK		(0xf << 27)
> diff --git a/drivers/gpu/drm/i915/intel_dsi.c
> b/drivers/gpu/drm/i915/intel_dsi.c
> index 16732e7..043441e 100644
> --- a/drivers/gpu/drm/i915/intel_dsi.c
> +++ b/drivers/gpu/drm/i915/intel_dsi.c
> @@ -548,6 +548,7 @@ static void intel_dsi_pre_enable(struct
> intel_encoder *encoder,
>  	struct drm_i915_private *dev_priv = to_i915(encoder-
> >base.dev);
>  	struct intel_dsi *intel_dsi = enc_to_intel_dsi(&encoder-
> >base);
>  	enum port port;
> +	u32 val;
>  
>  	DRM_DEBUG_KMS("\n");
>  
> @@ -558,6 +559,11 @@ static void intel_dsi_pre_enable(struct
> intel_encoder *encoder,
>  	intel_disable_dsi_pll(encoder);
>  	intel_enable_dsi_pll(encoder, pipe_config);
>  
> +	/* Add MIPI IO reset programming for modeset */
> +	val = I915_READ(BXT_P_CR_GT_DISP_PWRON);
> +	I915_WRITE(BXT_P_CR_GT_DISP_PWRON,
> +				val | MIPIO_RST_CTRL);
> +
Looking good but overall we still need to address Jani's comment to
limit these changes only to Broxton platform.

>  	intel_dsi_prepare(encoder, pipe_config);
>  
>  	/* Panel Enable over CRC PMIC */
> @@ -575,6 +581,12 @@ static void intel_dsi_pre_enable(struct
> intel_encoder *encoder,
>  		I915_WRITE(DSPCLK_GATE_D, val);
>  	}
>  
> +	/* Power up DSI regulator */
> +	I915_WRITE(BXT_P_DSI_REGULATOR_CFG, STAP_SELECT);
> +	val = I915_READ(BXT_P_DSI_REGULATOR_TX_CTRL);
> +	val &= ~HS_IO_CTRL_SELECT;
> +	I915_WRITE(BXT_P_DSI_REGULATOR_TX_CTRL, val);
> + 	/* put device in ready state */
>  	intel_dsi_device_ready(encoder);
>  
> @@ -707,6 +719,7 @@ static void intel_dsi_post_disable(struct
> intel_encoder *encoder,
>  {
>  	struct drm_i915_private *dev_priv = to_i915(encoder-
> >base.dev);
>  	struct intel_dsi *intel_dsi = enc_to_intel_dsi(&encoder-
> >base);
> +	u32 val;
>  
>  	DRM_DEBUG_KMS("\n");
>  
> @@ -714,8 +727,16 @@ static void intel_dsi_post_disable(struct
> intel_encoder *encoder,
>  
>  	intel_dsi_clear_device_ready(encoder);
>  
> +	val = I915_READ(BXT_P_CR_GT_DISP_PWRON);
> +	I915_WRITE(BXT_P_CR_GT_DISP_PWRON,
> +				val & ~MIPIO_RST_CTRL);
> +
>  	intel_disable_dsi_pll(encoder);
>  
> +	/* Power down DSI regulator to save power */
> +	I915_WRITE(BXT_P_DSI_REGULATOR_CFG, STAP_SELECT);
> +	I915_WRITE(BXT_P_DSI_REGULATOR_TX_CTRL, HS_IO_CTRL_SELECT);
> +
>  	if (IS_VALLEYVIEW(dev_priv) || IS_CHERRYVIEW(dev_priv)) {
>  		u32 val;
>  
-- 
Mika Kahola - Intel OTC