[Intel-gfx] [PATCH v3 2/4] drm/i915/psr: Account for sink CRC raciness on some panels

Jani Nikula jani.nikula at intel.com
Fri Jul 14 09:46:08 UTC 2017


On Tue, 11 Jul 2017, Jim Bride <jim.bride at linux.intel.com> wrote:
> According to the eDP spec, when the count field in TEST_SINK_MISC
> increments then the six bytes of sink CRC information in the DPCD
> should be valid.  Unfortunately, this doesn't seem to be the case
> on some panels, and as a result we get some incorrect and inconsistent
> values from the sink CRC DPCD locations at times.  This problem exhibits
> itself more on faster processors (relative failure rates HSW < SKL < KBL.)
> In order to try and account for this, we try a lot harder to read the sink
> CRC until we get consistent values twice in a row before returning what we
> read and delay for a time before trying to read.  We still see some
> occasional failures, but reading the sink CRC is much more reliable,
> particularly on SKL and KBL, with these changes than without.
>
> v2: * Reduce number of retries when reading the sink CRC (Jani)
>     * Refactor to minimize changes to the code (Jani)
>     * Rebase
>
> Cc: Rodrigo Vivi <rodrigo.vivi at intel.com>
> Cc: Paulo Zanoni <paulo.r.zanoni at intel.com>
> Cc: Jani Nikula <jani.nikula at intel.com>
> Reviewed-by: Rodrigo Vivi <rodrigo.vivi at intel.com>
> Signed-off-by: Jim Bride <jim.bride at linux.intel.com>
> ---
>  drivers/gpu/drm/i915/intel_dp.c | 40 ++++++++++++++++++++++++++++++++++++----
>  1 file changed, 36 insertions(+), 4 deletions(-)
>
> diff --git a/drivers/gpu/drm/i915/intel_dp.c b/drivers/gpu/drm/i915/intel_dp.c
> index 2d42d09..69c8130c 100644
> --- a/drivers/gpu/drm/i915/intel_dp.c
> +++ b/drivers/gpu/drm/i915/intel_dp.c
> @@ -3906,6 +3906,14 @@ int intel_dp_sink_crc(struct intel_dp *intel_dp, u8 *crc)
>  	u8 buf;
>  	int count, ret;
>  	int attempts = 6;
> +	u8 old_crc[6];
> +
> +	if (crc != NULL) {

As DK said, please drop the check.

> +		memset(crc, 0, 6);
> +		memset(old_crc, 0xff, 6);

Both unnecessary, see below.

> +	} else {
> +		return -ENOMEM;
> +	}
>  
>  	ret = intel_dp_sink_crc_start(intel_dp);
>  	if (ret)
> @@ -3929,11 +3937,35 @@ int intel_dp_sink_crc(struct intel_dp *intel_dp, u8 *crc)
>  		goto stop;
>  	}
>  
> -	if (drm_dp_dpcd_read(&intel_dp->aux, DP_TEST_CRC_R_CR, crc, 6) < 0) {
> -		ret = -EIO;
> -		goto stop;
> -	}
> +	attempts = 6;
> +
> +	/*
> +	 * Sometimes it takes a while for the "real" CRC values to land in
> +	 * the DPCD, so try several times until we get two reads in a row
> +	 * that are the same.  If we're an eDP panel, delay between reads
> +	 * for a while since the values take a bit longer to propagate.
> +	 */
> +	do {

Never use a do-while when a for loop will do. for (i = 0; i < 6; i++)
gets interpreted in the spine, no need for further processing.

> +		intel_wait_for_vblank(dev_priv, intel_crtc->pipe);
> +		if (is_edp(intel_dp))
> +			usleep_range(20000, 25000);

Is the intention to do these *between* reads? If yes, then move this
*after* the memcmp to only do this between reads.

> +
> +		if (drm_dp_dpcd_read(&intel_dp->aux, DP_TEST_CRC_R_CR,
> +				     crc, 6) < 0) {
> +			ret = -EIO;
> +			goto stop;

break;

> +		}
> +
> +		if (memcmp(old_crc, crc, 6) == 0) {
> +			ret = 0;
> +			goto stop;
> +		} else {
> +			memcpy(old_crc, crc, 6);
> +		}

After you've switched this to the for loop, you can do:

	if (i && memcmp(old_crc, crc, sizeof(old_crc)) == 0)
        	break;
	memcpy(old_crc, crc, sizeof(old_crc));

> +	} while (--attempts);
>  

	if (i == 6) {

> +	DRM_DEBUG_KMS("Failed to get CRC after 6 attempts.\n");
> +	ret = -ETIMEDOUT;

	}

>  stop:
>  	intel_dp_sink_crc_stop(intel_dp);
>  	return ret;

-- 
Jani Nikula, Intel Open Source Technology Center


More information about the Intel-gfx mailing list